hwvdsl2SeltTestParaVarUerC
HUAWEI-VDSL2-PRIV-MIB ·
.1.3.6.1.4.1.2011.6.115.1.7.1.1.1.65551
Object
column
OctetString
The relative variance of the uncalibrated echo response REL_VAR_UER(i* UER_G *Df) shall be represented as an 8-bit unsigned integer v(i), where i is the subcarrier index i = 0 to NSC-1. The value of REL_VAR_UER(i* UER_G *Df) shall be defined as REL_VAR_UER(i* UER_G *Df) = 3 - v(i)/2 dB. The number v(i) is an 8-bit unsigned integer in the range 0 to 254. This data format supports a REL_VAR_UER(i) over a range from -124 dB to +3 dB for each carrier with a granularity from 0.5 dB. Out of range values shall be clamped to the closest range bound. The special value v(i) = 255 indicates that no measurement is available for that carrier. Unit: 0.5dB
Context
- MIB
- HUAWEI-VDSL2-PRIV-MIB
- OID
.1.3.6.1.4.1.2011.6.115.1.7.1.1.1.65551- Type
- column
- Access
- readonly
- Status
- current
- Parent
- vdsl2SeltTestEntry
- Table
- vdsl2SeltTestTable
- Siblings
- 32
Syntax
OctetString
Values & Constraints
Object Constraints
range: 0-8192
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| vdsl2SeltTestOperType This object is used to start the VDSL SELT. Only the start of the SELT is supported current. The stop of the SELT is not supported. | column | VSDLSELTOPERTYPE | .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.1 |
| vdsl2SeltTestParamDwnShnCap Selt test parameter Downstream Shannon Capacity. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.10 |
| vdsl2SeltTestParamInbandNoise Selt test parameter Inband Noise
4096 values that indicate inband noise in DB/Hz,
covering VDSL bands, from 0 to 30 MHz. | column | OctetString | .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.11 |
| vdsl2SeltTestParamTerminResp Selt test parameter Termination Response
180 values that indicate termination response magnitude from 0 to 18 kft. | column | OctetString | .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.12 |
| vdsl2SeltTestParamUpMgnAtRate Selt test parameter Upstream Rate vs. Margin
This value is a measure of the quality of your upstream data
signal relative to the noise on the line. Hundreds of val… | column | OctetString | .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.13 |
| vdsl2SeltTestParamDwnMgnAtRate Selt test parameter Downstream Rate vs. Margin
This value is a measure of the quality of your downstream data
signal relative to the noise on the line. Hundreds o… | column | OctetString | .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.14 |
| vdsl2SeltTestParamUpRateAtMgn Selt test parameter Upstream Margin vs. Rate | column | OctetString | .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.15 |
| vdsl2SeltTestParamDwnRateAtMgn Selt test parameter Downstream Margin vs. Rate | column | OctetString | .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.16 |
| vdsl2SeltTestOperResult Selt test operation result. | column | VSDLSELTOPERRESULT | .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.2 |
| vdsl2SeltTestResultNo Selt test result serial number. | column | Integer32 | .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.3 |
| vdsl2SeltTestResultLastFlag Last package flag for test result. | column | VSDLSELTRESULTLASTFLAG | .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.4 |
| vdsl2SeltTestResult Selt test result data. | column | OctetString | .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.5 |
| vdsl2SeltTestParamLoopLength Selt test parameter Loop Length. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.6 |
| hwvdsl2SeltTestParamAttnAt180KHZ Selt test parameter AttnAt180KHZ.
It ranges from -950 to 0 (physical values are -95 to 0 dB).
The invalid value is -1. If no SELT is performed, no SELT data is generated
because… | column | 0.1 dB SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.65535 |
| hwvdsl2SeltTestParamAttnAt300KHZ Selt test parameter AttnAt300KHZ.
It ranges from -950 to 0 (physical values are -95 to 0 dB).
The invalid value is -1. If no SELT is performed, no SELT data is generated
because… | column | 0.1 dB SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.65536 |
| hwvdsl2SeltTestParamQSPsdValue Selt test parameter QuietSignal PSD.
An array of 4096 16-bits values,
designed for supporting up to 4096 (downstream) sub-carriers.
It ranges from -150 to -40 units of 1dBm/Hz. | column | OctetString | .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.65537 |
| hwvdsl2SeltTestParamUnCalibLineScale The scale factor of uncalibrated echo response shall be coded as a 32 bit unsigned integer. | column | Unsigned32 | .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.65538 |
| hwvdsl2SeltTestParamUnCalibEchoRespRealSegment1 The uncalibrated echo response, UER(i* UER_G*Df), shall be represented in linear format by a
scale factor and a normalized complex number a(i)+j*b(i), where i is a frequency index… | column | OctetString | .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.65539 |
| hwvdsl2SeltTestParamUnCalibEchoRespRealSegment2 The uncalibrated echo response, UER(i* UER_G*Df), shall be represented in linear format by a
scale factor and a normalized complex number a(i)+j*b(i), where i is a frequency index… | column | OctetString | .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.65540 |
| hwvdsl2SeltTestParamUnCalibEchoRespImgSegment1 The uncalibrated echo response, UER(i* UER_G*Df), shall be represented in linear format by a
scale factor and a normalized complex number a(i)+j*b(i), where i is a frequency index… | column | OctetString | .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.65541 |
| hwvdsl2SeltTestParamUnCalibEchoRespImgSegment2 The uncalibrated echo response, UER(i* UER_G*Df), shall be represented in linear format by a
scale factor and a normalized complex number a(i)+j*b(i), where i is a frequency index… | column | OctetString | .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.65542 |
| hwvdsl2SeltTestParamQlnGroupSize Number of QLN(quiet line noise) per group.
The scale value is 1 or 4294967295.4294967295 is invalid value. | column | Unsigned32 | .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.65548 |
| hwvdsl2SeltTestParamQmeC The status of QLN capture switch.
Options:
1. enable(1) - Enable QLN capture switch
2. disable(2) - Disable QLN capture switch
3. invalid(-1) - Invalid value | column | Enumeration | .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.65549 |
| hwvdsl2SeltTestParamUmeC The status of UER capture switch.
Options:
1. enable(1) - Enable UER capture switch
2. disable(2) - Disable UER capture switch
3. invalid(-1) - Invalid value | column | Enumeration | .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.65550 |
| hwvdsl2SeltTestParaUerMmdC This parameter is the maximum allowed time for SELT uncalibrated echo response measurement,
between the time of the start command written by the SELT-PMD-ME, and the time the resu… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.65552 |
| hwvdsl2SeltTestParaQlnMmdC This parameter is the maximum allowed time for SELT quiet line noise measurement, between the
time of the start command written by the SELT-PMD-ME, and the time the result is avai… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.65553 |
| hwvdsl2SeltTestParaUerStatus UerStatus.
Options:
1.off(1) - The status is off.
2.running(2) - The status is running.
3.completed(3) - The status is completed.
4.failed(4) - … | column | Enumeration | .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.65554 |
| hwvdsl2SeltTestParaQlnStatus QlnStatus.
Options:
1.off(1) - The status is off.
2.running(2) - The status is running.
3.completed(3) - The status is completed.
4.failed(4) - … | column | Enumeration | .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.65555 |
| hwvdsl2SeltTestParamCalcEnable The status of calculation switch.
Options:
1. enable(1) - Enable calculation switch
2. disable(2) - Disable calculation switch
3. invalid(-1) - Invalid value
Def… | column | Enumeration | .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.65556 |
| vdsl2SeltTestParamLoopTermin Selt test parameter Loop Termination. | column | VSDLSELTPARAMLOOPTERMIN | .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.7 |
| vdsl2SeltTestParamLoopGauge Selt test parameter Loop Gauge. | column | VSDLSELTPARAMLOOPGAUGE | .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.8 |
| vdsl2SeltTestParamUpShnCap Selt test parameter Upstream Shannon Capacity. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.9 |