hwRsvpTeSenderLabelRequestAtmMinVpi
HUAWEI-RSVPTE-MIB ·
.1.3.6.1.4.1.2011.5.25.148.1.2.1.50
Object
column
SNMPv2-SMIInteger32
This 12 bit field specifies the lower bound of a block of Virtual Path Identifiers that is supported on the originating switch. If the VPI is less than 12-bits it must be right justified in this field and preceding bits must be set to zero.
Context
- MIB
- HUAWEI-RSVPTE-MIB
- OID
.1.3.6.1.4.1.2011.5.25.148.1.2.1.50- Type
- column
- Access
- readonly
- Status
- current
- Parent
- hwRsvpTeSenderEntry
- Table
- hwRsvpTeSenderTable
- Siblings
- 72
Syntax
SNMPv2-SMIInteger32
- Source
- SNMPv2-SMIInteger32
- Base type
Integer32
Values & Constraints
Type Constraints
range: -2147483648..2147483647
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| hwRsvpTeSenderNumber The number of this sender. This is for SNMP
Indexing purposes only and has no relation to
any protocol value. | column | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.2011.5.25.148.1.2.1.1 |
| hwRsvpTeSenderTSpecRate The Average Bit Rate of the sender's data
stream. Within a transmission burst, the ar-
rival rate may be as fast as hwRsvpTeSenderTSpec-
PeakRate (if supported by the … | column | bits per second INTEGRATED-SERVICES-MIBBitRate | .1.3.6.1.4.1.2011.5.25.148.1.2.1.10 |
| hwRsvpTeSenderTSpecPeakRate The Peak Bit Rate of the sender's data stream.
Traffic arrival is not expected to exceed this
rate at any time, apart from the effects of
jitter in the network. If not speci… | column | bits per second INTEGRATED-SERVICES-MIBBitRate | .1.3.6.1.4.1.2011.5.25.148.1.2.1.11 |
| hwRsvpTeSenderTSpecBurst The size of the largest burst expected from
the sender at a time. | column | bytes INTEGRATED-SERVICES-MIBBurstSize | .1.3.6.1.4.1.2011.5.25.148.1.2.1.12 |
| hwRsvpTeSenderTSpecMinTu The minimum message size for this flow. The
policing algorithm will treat smaller messages
as though they are this size. | column | INTEGRATED-SERVICES-MIBMessageSize | .1.3.6.1.4.1.2011.5.25.148.1.2.1.13 |
| hwRsvpTeSenderTSpecMaxTu The maximum message size for this flow. The
admission algorithm will reject TSpecs whose
Maximum Transmission Unit, plus the interface
headers, exceed the interface MTU. | column | INTEGRATED-SERVICES-MIBMessageSize | .1.3.6.1.4.1.2011.5.25.148.1.2.1.14 |
| hwRsvpTeSenderInterval The interval between refresh messages as ad-
vertised by the previous hop. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.25.148.1.2.1.15 |
| hwRsvpTeSenderRsvpHop If TRUE, the node believes that the previous
IP hop is an RSVP hop. If FALSE, the node be-
lieves that the previous IP hop may not be an
RSVP hop. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2011.5.25.148.1.2.1.16 |
| hwRsvpTeSenderPolicy The contents of the policy object, displayed
as an uninterpreted string of octets, including
the object header. In the absence of such an
object, this should be of zero lengt… | column | OctetString | .1.3.6.1.4.1.2011.5.25.148.1.2.1.17 |
| hwRsvpTeSenderAdspecBreak The global break bit general characterization
parameter from the ADSPEC. If TRUE, at least
one non-IS hop was detected in the path. If
FALSE, no non-IS hops were detected. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2011.5.25.148.1.2.1.18 |
| hwRsvpTeSenderAdspecHopCount The hop count general characterization parame-
ter from the ADSPEC. A return of zero or
noSuchValue indicates one of the following con-
ditions:
the inval… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.25.148.1.2.1.19 |
| hwRsvpTeSenderType The type of session (IP4, IP6, IP6 with flow
information, etc). | column | INTEGRATED-SERVICES-MIBSessionType | .1.3.6.1.4.1.2011.5.25.148.1.2.1.2 |
| hwRsvpTeSenderAdspecPathBw The path bandwidth estimate general character-
ization parameter from the ADSPEC. A return of
zero or noSuchValue indicates one of the fol-
lowing conditions:
… | column | bits per second INTEGRATED-SERVICES-MIBBitRate | .1.3.6.1.4.1.2011.5.25.148.1.2.1.20 |
| hwRsvpTeSenderAdspecMinLatency The minimum path latency general characteriza-
tion parameter from the ADSPEC. A return of
zero or noSuchValue indicates one of the fol-
lowing conditions:
… | column | microseconds SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.25.148.1.2.1.21 |
| hwRsvpTeSenderAdspecMtu The composed Maximum Transmission Unit general
characterization parameter from the ADSPEC. A
return of zero or noSuchValue indicates one of
the following conditions:
… | column | bytes SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.25.148.1.2.1.22 |
| hwRsvpTeSenderAdspecGuaranteedSvc If TRUE, the ADSPEC contains a Guaranteed Ser-
vice fragment. If FALSE, the ADSPEC does not
contain a Guaranteed Service fragment. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2011.5.25.148.1.2.1.23 |
| hwRsvpTeSenderAdspecGuaranteedBreak If TRUE, the Guaranteed Service fragment has
its 'break' bit set, indicating that one or
more nodes along the path do not support the
guaranteed service. If FALSE, a… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2011.5.25.148.1.2.1.24 |
| hwRsvpTeSenderAdspecGuaranteedCtot If hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this
is the end-to-end composed value for the
guaranteed service 'C' parameter. A return of
zero or noSuchValue indicates … | column | bytes SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.25.148.1.2.1.25 |
| hwRsvpTeSenderAdspecGuaranteedDtot If hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this
is the end-to-end composed value for the
guaranteed service 'D' parameter. A return of
zero or noSuchValue indicates … | column | microseconds SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.25.148.1.2.1.26 |
| hwRsvpTeSenderAdspecGuaranteedCsum If hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this
is the composed value for the guaranteed ser-
vice 'C' parameter since the last reshaping
point. A return of zero or no… | column | bytes SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.25.148.1.2.1.27 |
| hwRsvpTeSenderAdspecGuaranteedDsum If hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this
is the composed value for the guaranteed ser-
vice 'D' parameter since the last reshaping
point. A return of zero or no… | column | microseconds SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.25.148.1.2.1.28 |
| hwRsvpTeSenderAdspecGuaranteedHopCount If hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this
is the service-specific override of the hop
count general characterization parameter from
the ADSPEC. A return of zero… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.25.148.1.2.1.29 |
| hwRsvpTeSenderDestAddr The destination address used by all senders in
this session. | column | OctetString | .1.3.6.1.4.1.2011.5.25.148.1.2.1.3 |
| hwRsvpTeSenderAdspecGuaranteedPathBw If hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this
is the service-specific override of the path
bandwidth estimate general characterization
parameter from the ADSPEC. A re… | column | bits per second INTEGRATED-SERVICES-MIBBitRate | .1.3.6.1.4.1.2011.5.25.148.1.2.1.30 |
| hwRsvpTeSenderAdspecGuaranteedMinLatency If hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this
is the service-specific override of the minimum
path latency general characterization parameter
from the ADSPEC. A return of … | column | microseconds SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.25.148.1.2.1.31 |
| hwRsvpTeSenderAdspecGuaranteedMtu If hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this
is the service-specific override of the com-
posed Maximum Transmission Unit general charac-
terization parameter from the AD… | column | bytes SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.25.148.1.2.1.32 |
| hwRsvpTeSenderAdspecCtrlLoadSvc If TRUE, the ADSPEC contains a Controlled Load
Service fragment. If FALSE, the ADSPEC does
not contain a Controlled Load Service frag-
ment. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2011.5.25.148.1.2.1.33 |
| hwRsvpTeSenderAdspecCtrlLoadBreak If TRUE, the Controlled Load Service fragment
has its 'break' bit set, indicating that one or
more nodes along the path do not support the
controlled load service. If … | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2011.5.25.148.1.2.1.34 |
| hwRsvpTeSenderAdspecCtrlLoadHopCount If hwRsvpTeSenderAdspecCtrlLoadSvc is TRUE, this
is the service-specific override of the hop
count general characterization parameter from
the ADSPEC. A return of zero… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.25.148.1.2.1.35 |
| hwRsvpTeSenderAdspecCtrlLoadPathBw If hwRsvpTeSenderAdspecCtrlLoadSvc is TRUE, this
is the service-specific override of the path
bandwidth estimate general characterization
parameter from the ADSPEC. A re… | column | bits per second INTEGRATED-SERVICES-MIBBitRate | .1.3.6.1.4.1.2011.5.25.148.1.2.1.36 |
| hwRsvpTeSenderAdspecCtrlLoadMinLatency If hwRsvpTeSenderAdspecCtrlLoadSvc is TRUE, this
is the service-specific override of the minimum
path latency general characterization parameter
from the ADSPEC. A return of … | column | microseconds SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.25.148.1.2.1.37 |
| hwRsvpTeSenderAdspecCtrlLoadMtu If hwRsvpTeSenderAdspecCtrlLoadSvc is TRUE, this
is the service-specific override of the com-
posed Maximum Transmission Unit general charac-
terization parameter from the AD… | column | bytes SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.25.148.1.2.1.38 |
| hwRsvpTeSenderTtl The TTL value in the RSVP header that was last
received. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.25.148.1.2.1.39 |
| hwRsvpTeSenderAddr The source address used by this sender in this
session. | column | OctetString | .1.3.6.1.4.1.2011.5.25.148.1.2.1.4 |
| hwRsvpTeLspId A 16-bit identifier used in the SENDER_TEMPLATE
and the FILTER_SPEC that can be changed to
allow a sender to share resources with itself. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.25.148.1.2.1.40 |
| hwRsvpTeSenderMsgIdSndFlag Indicates that the message sender requests the
peer to send an acknowledgment for the message.
(0x01: ACK desired.) | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.25.148.1.2.1.41 |
| hwRsvpTeSenderMsgIdSndEpoch A value that indicates when the Message_Identi-
fier sequence has been reset. | column | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.2011.5.25.148.1.2.1.42 |
| hwRsvpTeSenderMsgIdSndNumber When combined with the message generator's IP
address, the Message_Identifier field uniquely
identifies a message. The values placed in this
field change incrementally and onl… | column | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.2011.5.25.148.1.2.1.43 |
| hwRsvpTeSenderMsgIdRcvFlag The message ID flag of the message latest received.
It is used to identify whether ACK is desired or
not. And it can be extended. (0x01: ACK desired.) | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.25.148.1.2.1.44 |
| hwRsvpTeSenderMsgIdRcvEpoch The message ID epoch of the message latest
received form the interface. | column | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.2011.5.25.148.1.2.1.45 |
| hwRsvpTeSenderMsgIdRcvNumber The message ID number of the message latest
received form the interface. A return of 0
indicates the absence of the MESSAGE_ID
object received. | column | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.2011.5.25.148.1.2.1.46 |
| hwRsvpTeSenderClassType Indicates the class-type. A return of zero
indicates the absence of the object. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.25.148.1.2.1.47 |
| hwRsvpTeSenderLabelRequestCtype The type of label request (without label range,
with ATM label range, with frame relay label
range, etc). | column | Enumeration | .1.3.6.1.4.1.2011.5.25.148.1.2.1.48 |
| hwRsvpTeSenderLabelRequestL3pid An identifier of the layer 3 protocol using
this path. Standard Ethertype values are used. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.25.148.1.2.1.49 |
| hwRsvpTeSenderDestAddrLength The length of the destination address in bits.
This is the CIDR Prefix Length, which for IP4
hosts and multicast addresses is 32 bits. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.25.148.1.2.1.5 |
| hwRsvpTeSenderLabelRequestAtmMinVci This 16 bit field specifies the lower bound of
a block of Virtual Connection Identifiers that
is supported on the originating switch. If the
VCI is less than 16-bits it must b… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.25.148.1.2.1.51 |
| hwRsvpTeSenderLabelRequestAtmMaxVpi This 12 bit field specifies the upper bound of
a block of Virtual Path Identifiers that is
supported on the originating switch. If the
VPI is less than 12-bits it must be righ… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.25.148.1.2.1.52 |
| hwRsvpTeSenderLabelRequestAtmMaxVci This 16 bit field specifies the upper bound of
a block of Virtual Connection Identifiers that
is supported on the originating switch. If the
VCI is less than 16-bits it must b… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.25.148.1.2.1.53 |
| hwRsvpTeSenderLabelRequestFrMinDlci This 23-bit field specifies the lower bound of
a block of Data Link Connection Identifiers
(DLCIs) that is supported on the originating
switch. The DLCI must be right justifie… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.25.148.1.2.1.54 |
| hwRsvpTeSenderLabelRequestFrMaxDlci This 23-bit field specifies the upper bound of
a block of Data Link Connection Identifiers
(DLCIs) that is supported on the originating
switch. The DLCI must be right justifie… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.25.148.1.2.1.55 |
| hwRsvpTeSenderSessionAttrType The type of the session_attribute (without
resource affinities or with resource affinities). | column | Enumeration | .1.3.6.1.4.1.2011.5.25.148.1.2.1.56 |
| hwRsvpTeSenderSessionAttrSetupPrio The priority of the session with respect to
taking resources, in the range of 0 to 7. The
value 0 is the highest priority. The Setup
Priority is used in deciding whether this … | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.25.148.1.2.1.57 |
| hwRsvpTeSenderSessionAttrHoldPrio The priority of the session with respect to
holding resources, in the range of 0 to 7. The
value 0 is the highest priority. Holding
Priority is used in deciding whether this
… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.25.148.1.2.1.58 |
| hwRsvpTeSenderSessionAttrFlag A mixed value. (0x01: Local protection desired;
0x02: Label recording desired; 0x04: SE Style
desired; 0x08: bandwidth protection desired;
0x10: node protection desired; 0x20: Pa… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.25.148.1.2.1.59 |
| hwRsvpTeSenderAddrLength The length of the sender's address in bits.
This is the CIDR Prefix Length, which for IP4
hosts and multicast addresses is 32 bits. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.25.148.1.2.1.6 |
| hwRsvpTeSenderSessionAttrName Session name, a null padded string of characters. | column | OctetString | .1.3.6.1.4.1.2011.5.25.148.1.2.1.60 |
| hwRsvpTeSenderSessionAttrExcludeAny A 32-bit vector representing a set of attribute
filters associated with a tunnel any of which
renders a link unacceptable. | column | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.2011.5.25.148.1.2.1.61 |
| hwRsvpTeSenderSessionAttrIncludeAny A 32-bit vector representing a set of attribute
filters associated with a tunnel any of which
renders a link acceptable (with respect to this
test). A null set (all bits set to … | column | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.2011.5.25.148.1.2.1.62 |
| hwRsvpTeSenderSessionAttrIncludeAll A 32-bit vector representing a set of attribute
filters associated with a tunnel all of which
must be present for a link to be acceptable
(with respect to this test). A null se… | column | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.2011.5.25.148.1.2.1.63 |
| hwRsvpTeSenderFrrSetupPrio The priority of the backup path with respect to
taking resources, in the range 0 to 7. The
value 0 is the highest priority. Setup Priority
is used in deciding whether this sess… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.25.148.1.2.1.64 |
| hwRsvpTeSenderFrrHoldPrio The priority of the backup path with respect to
holding resources, in the range 0 to 7. The
value 0 is the highest priority. Holding
Priority is used in deciding whether this … | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.25.148.1.2.1.65 |
| hwRsvpTeSenderFrrHopLimit The maximum number of extra hops the backup path
is allowed to take, from current node (a PLR)
to an MP, with PLR and MP excluded from the count.
For example, hop-limit of 0 mea… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.25.148.1.2.1.66 |
| hwRsvpTeSenderFrrFlag An enumerable value to indicate the protection
schema desired (0x01, One-to-One Backup Desired;
0x02, Facility Backup Desired; 0x03, No Backup
Desired). | column | Enumeration | .1.3.6.1.4.1.2011.5.25.148.1.2.1.67 |
| hwRsvpTeSenderFrrBandwidth Bandwidth estimate; 32-bit IEEE floating point
integer, in bits per second. | column | bits per second INTEGRATED-SERVICES-MIBBitRate | .1.3.6.1.4.1.2011.5.25.148.1.2.1.68 |
| hwRsvpTeSenderFrrExcludeAny A 32-bit vector representing a set of attribute
filters associated with a backup path, any of
which renders a link unacceptable. | column | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.2011.5.25.148.1.2.1.69 |
| hwRsvpTeSenderHopAddr The address used by the previous RSVP hop
(which may be the original sender). | column | OctetString | .1.3.6.1.4.1.2011.5.25.148.1.2.1.7 |
| hwRsvpTeSenderFrrIncludeAny A 32-bit vector representing a set of attribute
filters associated with a backup path, any of
which renders a link acceptable (with respect
to this test). A null set (all bits … | column | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.2011.5.25.148.1.2.1.70 |
| hwRsvpTeSenderFrrIncludeAll A 32-bit vector representing a set of attribute
filters associated with a backup path, all of
which must be present for a link to be
acceptable (with respect to this test). A n… | column | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.2011.5.25.148.1.2.1.71 |
| hwRsvpTeSenderFrrInuseFlag An enumerable value to indicate the fast-reroute
state of this sender (normal, PLR in use, MP in
use, PLR in use and MP in use, under protection). | column | Enumeration | .1.3.6.1.4.1.2011.5.25.148.1.2.1.72 |
| hwRsvpTeSenderDiffServPsc This 16 bits field indicates a PHB Scheduling
Class to be supported by the LSP. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.25.148.1.2.1.73 |
| hwRsvpTeSenderHopLih The Logical Interface Handle used by the pre-
vious RSVP hop (which may be the original
sender). | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.25.148.1.2.1.8 |
| hwRsvpTeSenderInterface The ifIndex value of the interface on which
this PATH message was most recently received. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.25.148.1.2.1.9 |