hwORCh0OnlineState
HUAWEI-ENVIRONMENT-MIB ·
.1.3.6.1.4.1.2011.6.1.1.7.1.58
Object
column
Enumeration
The state of channel 0 for the optical receiver. Options: 1.normal(1) - indicates that optical receiver channel 0 is normal 2.offline(2) - indicates that optical receiver channel 0 is offline 3.fault(3) - indicates that optical receiver channel 0 is fault 4.config(4) - indicates that optical receiver channel 0 is config 5.autoload(5) - indicates that optical receiver channel 0 is autoload 6.manualshutdown(6) - indicates that optical receiver channel 0 is manualshutdown 7.mismatch(7) - indicates that optical receiver channel 0 is mismatch
Context
- MIB
- HUAWEI-ENVIRONMENT-MIB
- OID
.1.3.6.1.4.1.2011.6.1.1.7.1.58- Type
- column
- Access
- readonly
- Status
- current
- Parent
- hwOpticalNodeEntry
- Table
- hwOpticalNodeTable
- Siblings
- 78
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | normal |
2 | offline |
3 | fault |
4 | config |
5 | autoload |
6 | manualshutdown |
7 | mismatch |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| hwONCOMState The state of Optical node
The Optical node can be used only when it is online.
Options:
1.online(1) - indicates that Optical state is online
2.offline(2) - indicates that Op… | column | Enumeration | .1.3.6.1.4.1.2011.6.1.1.7.1.1 |
| hwOROpticalAGCStart This is the start value of the AGC range of the only channel for the single-channel optical receiver.
This is the start value of the AGC range of channel 0 for the dual-channel op… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.1.1.7.1.10 |
| hwORRFPowerValue The RF power value of Optical receiver. When the dual-channel optical receiver works in combination mode, this leaf indicates the RF power of channel 0.
Its unit is dBmV,its real … | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.1.1.7.1.11 |
| hwORRFPowerAlarmState The RF power alarm state of Optical receiver. When the dual-channel optical receiver works in combination mode, this leaf indicates the RF power alarm status of channel 0.
The Opt… | column | Enumeration | .1.3.6.1.4.1.2011.6.1.1.7.1.12 |
| hwORRFPowerLowThreshold The RF power low threshold of Optical receiver
Its unit is dBmV,its real accuracy is 0.1.
SNMP uses it which has been enlarged 10 by host.
user uses it which has been lessened 10 … | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.1.1.7.1.13 |
| hwORRFPowerHighThreshold The RF power high threshold of Optical receiver
Its unit is dBmV,its real accuracy is 0.1.
SNMP uses it which has been enlarged 10 by host.
user uses it which has been lessened 10… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.1.1.7.1.14 |
| hwORRFAttValue The RF ATT value of Optical receiver
Its unit is db.
Its range is 0db~10db. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.1.1.7.1.15 |
| hwORRFSwitch The RF switch of Optical receiver
The Optical receiver can be used only when it is on.
Options:
1.off(1) - indicates that RF Switch state is off
2.on(2) - indicates that R… | column | Enumeration | .1.3.6.1.4.1.2011.6.1.1.7.1.16 |
| hwONBarcode The barcode of Optical node
invalid(zero-length) | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.2011.6.1.1.7.1.17 |
| hwONCurrentInputVoltage1 The current input voltage1 of Optical node.
Its unit is V,its real accuracy is 0.1.
SNMP uses it which has been enlarged 10 by host.
user uses it which has been lessened 10 by SNM… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.1.1.7.1.18 |
| hwONCurrentInputVoltage2 The current input voltage2 of Optical node.
Its unit is V,its real accuracy is 0.1.
SNMP uses it which has been enlarged 10 by host.
user uses it which has been lessened 10 by SNM… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.1.1.7.1.19 |
| hwONModelNumber The model number of Optical node
invalid(zero-length) | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.2011.6.1.1.7.1.2 |
| hwORAGCRange This is the AGC range of the only channel for the single-channel optical receiver.
This is the AGC range of channel 0 for the dual-channel optical receiver. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.2011.6.1.1.7.1.20 |
| hwOTOpticalOutputPowerValue This is the power of the only channel for the single-channel optical transmitter.
This is the power of channel 0 for the dual-channel optical transmitter.
Its unit is 0.01dbm.
in… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.1.1.7.1.21 |
| hwOTOpticalOutputPowerAlarmState This is the power alarm state of the only channel for the single-channel optical transmitter.
This is the power alarm state of channel 0 for the dual-channel optical transmitter.
… | column | Enumeration | .1.3.6.1.4.1.2011.6.1.1.7.1.22 |
| hwOTOpticalOutputPowerLowThreshold This is the low power threshold of the only channel for the single-channel optical transmitter.
This is the low power threshold of channel 0 for the dual-channel optical transmitt… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.1.1.7.1.23 |
| hwOTOpticalOutputPowerHighThreshold This is the high power threshold of the only channel for the single-channel optical transmitter.
This is the high power threshold of channel 0 for the dual-channel optical transmi… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.1.1.7.1.24 |
| hwOTBiasValue This is the bias current value of the only channel for the single-channel optical transmitter.
This is the bias current value of channel 0 for the dual-channel optical transmitter… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.1.1.7.1.25 |
| hwOTBiasAlarmState This is the bias current alarm state of the only channel for the single-channel optical transmitter.
This is the bias current alarm state of channel 0 for the dual-channel optical… | column | Enumeration | .1.3.6.1.4.1.2011.6.1.1.7.1.26 |
| hwOTBiasLowThreshold This is the low bias current threshold of the only channel for the single-channel optical transmitter.
This is the low bias current threshold of channel 0 for the dual-channel o… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.1.1.7.1.27 |
| hwOTBiasHighThreshold This is the high bias current threshold of the only channel for the single-channel optical transmitter.
This is the high bias current threshold of channel 0 for the dual-channel… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.1.1.7.1.28 |
| hwOTWaveLength The wave length of Optical transmitter.
Its unit is nm.
Its value is 1310nm or 1550nm or 1610nm.
invalid(-1) | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.1.1.7.1.29 |
| hwONHardwareVer The hard version of Optical node
invalid(zero-length) | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.2011.6.1.1.7.1.3 |
| hwOROpticalWorkMode The protect-switch channel policy of dual-channel optical receiver.
Options:
1.force-channel0(1) - Force channel 0 as working channel, and forbid switching channel.
2.force-ch… | column | Enumeration | .1.3.6.1.4.1.2011.6.1.1.7.1.30 |
| hwOROpticalActiveChannel The working channel of dual-channel optical receiver.
invalid(-1). | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.1.1.7.1.31 |
| hwOROpticalCH1PowerValue This is the power of channel 1 for the dual-channel optical receiver.
Its unit is dbm,its real accuracy is 0.01.
SNMP uses it which has been enlarged 100 by host.
user uses it whi… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.1.1.7.1.32 |
| hwOROpticalCH1PowerAlarmState This is the power alarm state of channel 1 for the dual-channel optical receiver.
The optical receiver can be used only when it is normal.
Options:
1.normal(1) - indicates tha… | column | Enumeration | .1.3.6.1.4.1.2011.6.1.1.7.1.33 |
| hwOROpticalCH1PowerLowThreshold This is the low power threshold of channel 1 for the dual-channel optical receiver.
Its unit is dbm,its real accuracy is 0.01.
SNMP uses it which has been enlarged 100 by host.
us… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.1.1.7.1.34 |
| hwOROpticalCH1PowerHighThreshold This is the high power threshold of channel 1 for the dual-channel optical receiver.
Its unit is dbm,its real accuracy is 0.01.
SNMP uses it which has been enlarged 100 by host.
u… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.1.1.7.1.35 |
| hwOROpticalCH1AGCStart This is the start value of the AGC range of channel 1 for the dual-channel optical receiver.
Its unit is dBm,its real range is -4dBm~3dBm. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.1.1.7.1.36 |
| hwORAGCCH1Range This is the AGC range of channel 1 for the dual-channel optical receiver. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.2011.6.1.1.7.1.37 |
| hwORType The optical type of optical node.
Options:
1.optical-receiver(1)
2.optical-receiver/optical-transmitter(2)
3.dual-channel optical-receiver(3)
4.optical-receiver/dual-channel opt… | column | Enumeration | .1.3.6.1.4.1.2011.6.1.1.7.1.38 |
| hwOTOpticalOutputCH1PowerValue This is the power of channel 1 for the dual-channel optical transmitter.
Its unit is dbm,its real accuracy is 0.01.
SNMP uses it which has been enlarged 100 by host.
user uses it … | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.1.1.7.1.39 |
| hwONSoftwareVer The software version of Optical node
invalid(zero-length) | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.2011.6.1.1.7.1.4 |
| hwOTOpticalOutputCH1PowerAlarmState This is the power alarm state of channel 1 for the dual-channel optical transmitter.
The optical transmitter can be used only when it is normal.
Options:
1.normal(1) - indicat… | column | Enumeration | .1.3.6.1.4.1.2011.6.1.1.7.1.40 |
| hwOTOpticalOutputCH1PowerLowThreshold This is the low power threshold of channel 1 for the dual-channel optical transmitter.
Its unit is dbm,its real accuracy is 0.01.
SNMP uses it which has been enlarged 100 by host.… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.1.1.7.1.41 |
| hwOTOpticalOutputCH1PowerHighThreshold This is the high power threshold of channel 1 for the dual-channel optical transmitter.
Its unit is dbm,its real accuracy is 0.01.
SNMP uses it which has been enlarged 100 by host… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.1.1.7.1.42 |
| hwOTCH1BiasValue This is the bias current value of channel 1 for the dual-channel optical transmitter.
Its unit is mA,its normal range is 1mA~100mA.
invalid(-1) | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.1.1.7.1.43 |
| hwOTCH1BiasAlarmState This is the bias current alarm state of channel 1 for the dual-channel optical transmitter.
The optical transmitter can be used only when it is normal.
Options:
1.normal(1) - … | column | Enumeration | .1.3.6.1.4.1.2011.6.1.1.7.1.44 |
| hwOTCH1BiasLowThreshold This is the low bias current threshold of channel 1 for the dual-channel optical transmitter.
The alarm is produced when the bias current value is lower than this value.
Its unit … | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.1.1.7.1.45 |
| hwOTCH1BiasHighThreshold This is the high bias current threshold of channel 1 for the dual-channel optical transmitter.
The alarm is produced when the bias current value is higher than this value.
Its uni… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.1.1.7.1.46 |
| hwORCfgChannel0AGCMode Indicates the configuration information about the AGC gain on channel 0 for the optical receiver.
Options:
1.off(2) - indicates that AGC gain is off
2.minus6to2dBm(… | column | Enumeration | .1.3.6.1.4.1.2011.6.1.1.7.1.47 |
| hwORCfgChannel1AGCMode Indicates the configuration information about the AGC gain on channel 1 for the optical receiver.
Options:
1.off(2) - indicates that AGC gain is off
2.minus6to2dBm(… | column | Enumeration | .1.3.6.1.4.1.2011.6.1.1.7.1.48 |
| hwORRuninfoChannel0AGCMode Indicates the running information about the AGC gain on channel 0 for the optical receiver.
Options:
1.invalid(1) - indicates that AGC gain is not supported for the opt… | column | Enumeration | .1.3.6.1.4.1.2011.6.1.1.7.1.49 |
| hwONProductDate The product date of Optical node
field octets contents range
----- ------ -------- -----
1 1-4 year 0..65536
2 … | column | OctetString | .1.3.6.1.4.1.2011.6.1.1.7.1.5 |
| hwORRuninfoChannel1AGCMode Indicates the running information about the AGC gain on channel 1 for the optical receiver.
Options:
1.invalid(1) - indicates that AGC gain is not supported for the opt… | column | Enumeration | .1.3.6.1.4.1.2011.6.1.1.7.1.50 |
| hwORRFCH1PowerValue When the dual-channel optical receiver works in combination mode, this leaf takes effect and it indicates the RF power of channel 1.
Its unit is dBmV,its real accuracy is 0.1.
SN… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.1.1.7.1.51 |
| hwORRFCH1PowerAlarmState When the dual-channel optical receiver works in combination mode, this leaf takes effect and it indicates the RF power alarm status of channel 1.
The Optical receiver can be used… | column | Enumeration | .1.3.6.1.4.1.2011.6.1.1.7.1.52 |
| hwOTCH1WaveLength The wave length of channel 1 for the Optical transmitter .
Its unit is nm.
Its value is 1310nm or 1550nm or 1610nm.
invalid(-1) | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.1.1.7.1.53 |
| hwOTCfgOpticalWorkMode Indicates the configuration information about the work mode for the optical transmitter.
Options:
2.singleSGsingleTX(2) - indicates the working mode is single SG(service gro… | column | Enumeration | .1.3.6.1.4.1.2011.6.1.1.7.1.54 |
| hwOTRuninfoOpticalWorkMode Indicates the running information about the work mode for the optical transmitter.
1.invalid(1) - indicates the working mode is not supported for the optical transmitt… | column | Enumeration | .1.3.6.1.4.1.2011.6.1.1.7.1.55 |
| hwOTCH0RFAttValue This is the rf attenuation current value of channel 0 for the dual-channel optical transmitter.
Its unit is dB,its real accuracy is 0.1.
SNMP uses it which has been enlarged 10 by… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.1.1.7.1.56 |
| hwOTCH1RFAttValue This is the rf attenuation current value of channel 1 for the dual-channel optical transmitter.
Its unit is dB,its real accuracy is 0.1.
SNMP uses it which has been enlarged 10 by… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.1.1.7.1.57 |
| hwORCh1OnlineState The state of channel 1 for the optical receiver.
Options:
1.normal(1) - indicates that optical receiver channel 1 is normal
2.offline(2) - indicates that optical receiver ch… | column | Enumeration | .1.3.6.1.4.1.2011.6.1.1.7.1.59 |
| hwOROpticalPowerValue This is the power of the only channel for the single-channel optical receiver.
This is the power of channel 0 for the dual-channel optical receiver.
Its unit is dbm,its real accur… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.1.1.7.1.6 |
| hwOTCh0OnlineState The state of channel 0 for the optical transmitter.
Options:
1.normal(1) - indicates that optical transmitter channel 0 is normal
2.offline(2) - indicates that optical trans… | column | Enumeration | .1.3.6.1.4.1.2011.6.1.1.7.1.60 |
| hwOTCh1OnlineState The state of channel 1 for the optical transmitter.
Options:
1.normal(1) - indicates that optical transmitter channel 1 is normal
2.offline(2) - indicates that optical trans… | column | Enumeration | .1.3.6.1.4.1.2011.6.1.1.7.1.61 |
| hwONCfgOpticalWorkMode Indicates the configuration information about the work mode for the optical node.
Options:
1.invalid(1) - indicates the working mode is not supported for the optical node… | column | Enumeration | .1.3.6.1.4.1.2011.6.1.1.7.1.62 |
| hwONRuninfoOpticalWorkMode Indicates the configuration information about the work mode for the optical node.
Options:
1.invalid(1) - indicates the working mode is not supported for the optical node… | column | Enumeration | .1.3.6.1.4.1.2011.6.1.1.7.1.63 |
| hwOTCh0RuninfoOpticalLowPassFilter The low pass filter of channel 0 for the Optical transmitter .
Its unit is MHz.
Its value is 42MHz or 65MHz or 85MHz or 204MHz.
invalid(-1) | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.1.1.7.1.64 |
| hwOTCh1RuninfoOpticalLowPassFilter The low pass filter of channel 1 for the Optical transmitter .
Its unit is MHz.
Its value is 42MHz or 65MHz or 85MHz or 204MHz.
invalid(-1) | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.1.1.7.1.65 |
| hwONSmartCapability This MIB node is used to query the function of the optical node, which is represented by bits.
Functions of each bit are as follows:
1: setOTCHRFAttValue(0) - indicates whether… | column | Bits | .1.3.6.1.4.1.2011.6.1.1.7.1.66 |
| hwORRFPowerChangeThreshold The RF power change threshold of Optical receiver
Its unit is dBmV,its real accuracy is 0.1.
SNMP uses it which has been enlarged 10 by host.
user uses it which has been … | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.1.1.7.1.67 |
| hwORCHN0RFPowerReferenceValue The RF power reference value of Optical receiver. When the dual-channel optical receiver works in combination mode, this leaf indicates the RF power reference value of channel 0.
… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.1.1.7.1.68 |
| hwORCHN0RFPowerChangeValue The RF power change value of Optical receiver. When the dual-channel optical receiver works in combination mode, this leaf indicates the RF power change value of channel 0.
… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.1.1.7.1.69 |
| hwOROpticalPowerAlarmState This is the power alarm state of the only channel for the single-channel optical receiver.
This is the power alarm state of channel 0 for the dual-channel optical receiver.
The O… | column | Enumeration | .1.3.6.1.4.1.2011.6.1.1.7.1.7 |
| hwORCHN1RFPowerReferenceValue When the dual-channel optical receiver works in combination mode, this leaf takes effect and it indicates the RF power reference value of channel 1.
Its unit is dBmV,its rea… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.1.1.7.1.70 |
| hwORCHN1RFPowerChangeValue When the dual-channel optical receiver works in combination mode, this leaf takes effect and it indicates the RF power change value of channel 1.
Its unit is dBmV,its real a… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.1.1.7.1.71 |
| hwORCH0CurrentInputVoltage1 The RX CH0 current input voltage1 of Optical node.
Its unit is V,its real accuracy is 0.1.
SNMP uses it which has been enlarged 10 by host.
user uses it which has been lessened 10… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.1.1.7.1.72 |
| hwORCH0CurrentInputVoltage2 The RX CH0 current input voltage2 of Optical node.
Its unit is V,its real accuracy is 0.1.
SNMP uses it which has been enlarged 10 by host.
user uses it which has been lessened 10… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.1.1.7.1.73 |
| hwORCH1CurrentInputVoltage1 The RX CH1 current input voltage1 of Optical node.
Its unit is V,its real accuracy is 0.1.
SNMP uses it which has been enlarged 10 by host.
user uses it which has been lessened 10… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.1.1.7.1.74 |
| hwORCH1CurrentInputVoltage2 The RX CH1 current input voltage2 of Optical node.
Its unit is V,its real accuracy is 0.1.
SNMP uses it which has been enlarged 10 by host.
user uses it which has been lessened 10… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.1.1.7.1.75 |
| hwOTCH0CurrentInputVoltage1 The TX CH0 current input voltage1 of Optical node.
Its unit is V,its real accuracy is 0.1.
SNMP uses it which has been enlarged 10 by host.
user uses it which has been lessened 10… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.1.1.7.1.76 |
| hwOTCH0CurrentInputVoltage2 The TX CH0 current input voltage2 of Optical node.
Its unit is V,its real accuracy is 0.1.
SNMP uses it which has been enlarged 10 by host.
user uses it which has been lessened 10… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.1.1.7.1.77 |
| hwOTCH1CurrentInputVoltage1 The TX CH1 current input voltage1 of Optical node.
Its unit is V,its real accuracy is 0.1.
SNMP uses it which has been enlarged 10 by host.
user uses it which has been lessened 10… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.1.1.7.1.78 |
| hwOTCH1CurrentInputVoltage2 The TX CH1 current input voltage2 of Optical node.
Its unit is V,its real accuracy is 0.1.
SNMP uses it which has been enlarged 10 by host.
user uses it which has been lessened 10… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.1.1.7.1.79 |
| hwOROpticalPowerLowThreshold This is the low power threshold of the only channel for the single-channel optical receiver.
This is the low power threshold of channel 0 for the dual-channel optical receiver.
I… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.1.1.7.1.8 |
| hwOROpticalPowerHighThreshold This is the high power threshold of the only channel for the single-channel optical receiver.
This is the high power threshold of channel 0 for the dual-channel optical receiver. … | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.1.1.7.1.9 |