fwlFilterTos

FIREWALL-MIB · .1.3.6.1.4.1.2076.16.2.3.1.9

MIB view Table view

Object

column r/w SNMPv2-SMIInteger32

The IP TOS bit to be checked against the packet. This is a 
single byte integer of which the last three bits (least 
significant bits) indicate Delay, Throughput and Reliability 
i.e. 'uuuuudtr', u-unused, d-delay, t-throughput, r-reliability.
For example '6' indicates low delay and high throughput.

Context

MIB: FIREWALL-MIB
OID: .1.3.6.1.4.1.2076.16.2.3.1.9
Type: column
Access: readwrite
Status: current
Parent: fwlDefnFilterEntry
Table: fwlDefnFilterTable
Siblings: 15

Syntax

SNMPv2-SMIInteger32

Source: SNMPv2-SMIInteger32
Base type: Integer32

Values & Constraints

Type Constraints

range: -2147483648..2147483647

Related Objects

Sibling Objects

Object	Type	Syntax	OID
fwlFilterFilterName This Filter name uniquely identifies the particular Filter configured.	column	OctetString	`.1.3.6.1.4.1.10876.101.1.16.2.3.1.1`
fwlFilterAccounting This object is used to enable or disable the filter accounting of this filter. If this object is enabled then the Hit count of this filter will be incremented when the traffic mat…	column	Status	`.1.3.6.1.4.1.10876.101.1.16.2.3.1.10`
fwlFilterHitClear This object is used to clear the hit count of this filter. The default value is 'false'. When this object is true, the Hit count for the respective filter will be cleared and th…	column	SNMPv2-TCTruthValue	`.1.3.6.1.4.1.10876.101.1.16.2.3.1.11`
fwlFilterHitsCount The number of times this Filter is matched while processing the packet.	column	SNMPv2-SMICounter32	`.1.3.6.1.4.1.10876.101.1.16.2.3.1.12`
fwlFilterAddrType The address type of the source and destination address. This object is limited to IPv4 and IPv6 addresses.	column	INET-ADDRESS-MIBInetAddressType	`.1.3.6.1.4.1.10876.101.1.16.2.3.1.13`
fwlFilterFlowId The flow label identifier is specific to an IPv6 header as its to classify the same flow of packets between a source and destination in IPv6	column	Unsigned32	`.1.3.6.1.4.1.10876.101.1.16.2.3.1.14`
fwlFilterDscp The IP DSCP value is applicable for both IPv4 and IPv6, but when DSCP is specified TOS value(fwlFilterTos) should not be configured. Also TOS value (fwlFilterTos) is not applica…	column	Integer32	`.1.3.6.1.4.1.10876.101.1.16.2.3.1.15`
fwlFilterRowStatus This object allows entries to be created or deleted in this table.	column	SNMPv2-TCRowStatus	`.1.3.6.1.4.1.10876.101.1.16.2.3.1.16`
fwlFilterSrcAddress The source IP address and the source mask to be checked against the packet. The default value is 0.0.0.0/0. The address value should not be specified without the mask value. ('1…	column	SNMPv2-TCDisplayString	`.1.3.6.1.4.1.10876.101.1.16.2.3.1.2`
fwlFilterDestAddress The destination IP address and the destination mask to be checked against the packet. The default value is 0.0.0.0/0. The address value should not be specified without the mask …	column	SNMPv2-TCDisplayString	`.1.3.6.1.4.1.10876.101.1.16.2.3.1.3`
fwlFilterProtocol The type of protocol to be checked against the packet. The default value is 'any' (255). If the value is 'any' (255), it means that the protocol type can be anything and it will…	column	ProtocolType	`.1.3.6.1.4.1.10876.101.1.16.2.3.1.4`
fwlFilterSrcPort The source port to be checked against the packet. The range of port can be specified by using the symbols like '>', '<', '!=', '=', '<=', '>='. For example the port value will b…	column	SNMPv2-TCDisplayString	`.1.3.6.1.4.1.10876.101.1.16.2.3.1.5`
fwlFilterDestPort The destination port to be checked against the packet. The range of port can be specified by using the symbols like '>', '<', '!=', '=', '<=', '>='. For example the port value …	column	SNMPv2-TCDisplayString	`.1.3.6.1.4.1.10876.101.1.16.2.3.1.6`
fwlFilterAckBit deprecated ************** THIS OBJECT IS DEPRECATED ************** The TCP ACK bit to be checked against the packet. The default value is 'any'(3). It means that ACK bit …	column	Enumeration	`.1.3.6.1.4.1.10876.101.1.16.2.3.1.7`
fwlFilterRstBit deprecated ************** THIS OBJECT IS DEPRECATED ************** The TCP RST bit to be checked against the packet. The default value is 'any'(3). It means that RST bit …	column	Enumeration	`.1.3.6.1.4.1.10876.101.1.16.2.3.1.8`