eltexBgpPeerConfigIdleHold
ELTEX-BGP-MIB ·
.1.3.6.1.4.1.35265.45.1.2.1.1.1.20
Object
column
r/w
Unsigned32
The time to hold this peer in Idle state after a BGP
session has progressed beyond Idle state initially and
then returned to it. No new connections will be initiated
or accepted until the peer comes out of Idle state. By
setting this field to a large value, this timer can be
used to provide some level of peer oscillation damping, if
desired.
This field can be changed at any time. However, if the
field is changed while the peer is admin_status UP, the
change will only take effect after the peer has been
cycled admin_status DOWN and then UP, thus forcing the
peer session to be restarted.
Context
- MIB
- ELTEX-BGP-MIB
- OID
.1.3.6.1.4.1.35265.45.1.2.1.1.1.20- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- eltexBgpPeerEntry
- Table
- eltexBgpPeerTable
- Siblings
- 26
Syntax
Unsigned32
Values & Constraints
Object Constraints
range: 1-32767
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| eltexBgpPeerRemoteAddrType The address family of the remote address for the peering
session. | column | INET-ADDRESS-MIBInetAddressType | .1.3.6.1.4.1.35265.45.1.2.1.1.1.1 |
| eltexBgpPeerConfigDropWarn This object is used to determine whether the session is
dropped or a warning is generated when the maximum number
of prefixes set is exceeded.
Setting eltexBgpPeer… | column | EltexBgpConfigDropOrWarn | .1.3.6.1.4.1.35265.45.1.2.1.1.1.10 |
| eltexBgpPeerMaxPrfxHold The time interval in seconds between when this BGP session
is turn down due to the number of prefixes received from
this peer exceeding the maximum in
eltexBgpPeerConfigMaxPrfx an… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.35265.45.1.2.1.1.1.11 |
| eltexBgpPeerConfigThreshold A percentage of the limit set by eltexBgpPeerConfigMaxPrfx.
When the number of prefixes received from this peer reaches
this threshold, BGP issues a warning.
This f… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.35265.45.1.2.1.1.1.12 |
| eltexBgpPeerConnectRetryInterval Time interval for the ConnectRetry timer. The suggested
value for this timer is 120 seconds.
This field can be changed at any time. However, if the
field is chang… | column | Unsigned32 | .1.3.6.1.4.1.35265.45.1.2.1.1.1.13 |
| eltexBgpPeerHoldTimeConfigd Time interval in seconds for the Hold Time configured for
this BGP speaker with this peer. This value is placed in
an OPEN message sent to this peer by this BGP speaker, and
is c… | column | Unsigned32 | .1.3.6.1.4.1.35265.45.1.2.1.1.1.14 |
| eltexBgpPeerKeepAliveConfigd Time interval in seconds for the KeepAlive configured for
this BGP speaker with this peer. The value of this object
will only determine the KEEPALIVE messages frequency
relative … | column | Unsigned32 | .1.3.6.1.4.1.35265.45.1.2.1.1.1.15 |
| eltexBgpPeerMinRouteAdvertiseInterval Time interval in seconds for the
MinRouteAdvertisementInterval timer. This determines the
minimum time between a BGP UPDATE to a peer advertising or
withdrawing a route and a sub… | column | Unsigned32 | .1.3.6.1.4.1.35265.45.1.2.1.1.1.16 |
| eltexBgpPeerMinASOriginationInterval Time interval in seconds for determining the minimum amount
of time that must elapse between successive advertisements of
UPDATE messages that report changes to a route within the… | column | Unsigned32 | .1.3.6.1.4.1.35265.45.1.2.1.1.1.17 |
| eltexBgpPeerMinRouteWithdrawInterval Time interval in seconds for the MinRouteWithdrawInterval
timer. This is the interval which is enforced between
advertisement and subsequent withdrawal of a route.
… | column | Unsigned32 | .1.3.6.1.4.1.35265.45.1.2.1.1.1.18 |
| eltexBgpPeerConfigOpenDelay The delay to enforce in between a TCP connection with this
peer becoming established and a BGP Open message being
sent. If this delay is zero, then no delay will be
injected, and… | column | Unsigned32 | .1.3.6.1.4.1.35265.45.1.2.1.1.1.19 |
| eltexBgpPeerRemoteAddr The remote address for the peering session.
This is the address of the BGP peer. It must be specified
so the address length must be non-zero. | column | INET-ADDRESS-MIBInetAddress | .1.3.6.1.4.1.35265.45.1.2.1.1.1.2 |
| eltexBgpPeerDistListPlIn The Prefix List name identifying the Prefix List to use
to filter routes received from the peer. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.35265.45.1.2.1.1.1.21 |
| eltexBgpPeerDistListPlOut The Prefix List name identifying the Prefix List to use
to filter routes advertised to the peer. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.35265.45.1.2.1.1.1.22 |
| eltexBgpPeerReflectorClient This value indicates whether the given peer is a reflector
client of this router, or not. A value of nonClient(0)
indicates that this peer is not a reflector client. A
value of … | column | EltexBgpPeerReflectorClientType | .1.3.6.1.4.1.35265.45.1.2.1.1.1.23 |
| eltexBgpPeerSoftResetWithStoredInfo This option causes all routes learned from a peer to be stored
so that the ARI can be recalculated (for example, due to a
change in import policy) without performing a route refr… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.35265.45.1.2.1.1.1.24 |
| eltexBgpPeerConfigPeerGroup This is the index of the peer group. If a peer is not in
a peer group then its eltexBgpPeerConfigPeerGroup value is 0 | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.35265.45.1.2.1.1.1.25 |
| eltexBgpPeerPathMtuDiscovery Enable path MTU discovery. If the feature is enabled, all
packets are sent with the 'Do not fragment' flag to this peer.
The maximum segment size for TCP connection with this peer… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.35265.45.1.2.1.1.1.26 |
| eltexBgpPeerBfdDesired Indicates whether Bidirectional Forwarding Detection (BFD) is
desired for this peer.
This field can be changed at any time. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.35265.45.1.2.1.1.1.27 |
| eltexBgpPeerRowStatus The row status for this BGP peer table entry, used to
create and destroy table entries. | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.35265.45.1.2.1.1.1.3 |
| eltexBgpPeerAdminStatus The desired state of the BGP connection.
This parameter can be used to restart BGP peer
connections. Care should be used in providing write
access to this object w… | column | EltexBgpAdminStatus | .1.3.6.1.4.1.35265.45.1.2.1.1.1.4 |
| eltexBgpPeerOperStatus The current operational status of this peer. This usually
reflects the desired AdminStatus, but can contain transitional
values and failures. | column | EltexBgpOperStatus | .1.3.6.1.4.1.35265.45.1.2.1.1.1.5 |
| eltexBgpPeerRemoteAs The remote autonomous system number.
This field can be changed at any time. However, if the
field is changed while the peer is admin_status UP, the
change will onl… | column | EltexBgpAutonomousSystemNumber | .1.3.6.1.4.1.35265.45.1.2.1.1.1.6 |
| eltexBgpPeerSourceInterface The interface index for the interface from which the
source address for session is chosen. If non-zero, BGP
will look for the first address on this interface with a
type matching… | column | IF-MIBInterfaceIndexOrZero | .1.3.6.1.4.1.35265.45.1.2.1.1.1.7 |
| eltexBgpPeerNxtHopSlf When eltexBgpPeerNxtHopSlf is 'true', routes will be
advertised to the peer with NEXT_HOP attribute set to
BGP router local address. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.35265.45.1.2.1.1.1.8 |
| eltexBgpPeerConfigMaxPrfx This object is used to limit the number of prefixes that
can be accepted from this peer.
Setting eltexBgpPeerConfigMaxPrfx to a non-zero value sets
the maximum num… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.35265.45.1.2.1.1.1.9 |