swEgressACLIpRulePortGroup
EGRESSACL-MIB ·
.1.3.6.1.4.1.171.12.89.3.2.1.24
Object
column
r/w
Integer32
Specifies that the access rule will only apply to port(s)which belong to this port group.
This object and swEgressACLIpRuleVID,swEgressACLIpRulePort can not be set together.
When you set swEgressACLIpRuleVID or swEgressACLIpRulePort , the value of this object will change to 0 automatically.
Note:The range of this object is (0..N).The value N means the max number.It is
determined by the project itself. A value of 0 indicates that this object is not active.
Context
- MIB
- EGRESSACL-MIB
- OID
.1.3.6.1.4.1.171.12.89.3.2.1.24- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- swEgressACLIpRuleEntry
- Table
- swEgressACLIpRuleTable
- Siblings
- 29
Syntax
Integer32
- Source
- COPS-PR-SPPIInteger32
- Base type
Integer32
Values & Constraints
Type Constraints
range: -2147483648..2147483647
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| swEgressACLIpRuleProfileID The ID of the egress ACL mask entry, which is unique to the mask list.
The maximum value of this object depends on the device. | column | Integer32 | .1.3.6.1.4.1.171.12.89.3.2.1.1 |
| swEgressACLIpRuleDscp Specifies the value of DSCP. The value can be configured from 0 to 63.
A value of -1 indicates that this object is not active. | column | Integer32 | .1.3.6.1.4.1.171.12.89.3.2.1.10 |
| swEgressACLIpRuleProtocol Specifies the IP protocol. | column | Enumeration | .1.3.6.1.4.1.171.12.89.3.2.1.11 |
| swEgressACLIpRuleType Specifies that the rule applies to the value of ICMP/IGMP type traffic.
A value of -1 denotes that this object is not active. | column | Integer32 | .1.3.6.1.4.1.171.12.89.3.2.1.12 |
| swEgressACLIpRuleCode Specifies that the rule applies to the value of ICMP code traffic.
A value of -1 denotes that this object is not active. | column | Integer32 | .1.3.6.1.4.1.171.12.89.3.2.1.13 |
| swEgressACLIpRuleSrcPort Specifies that the rule applies to the range of the TCP/UDP source ports.
A value of -1 indicates that this object is not active. | column | Integer32 | .1.3.6.1.4.1.171.12.89.3.2.1.14 |
| swEgressACLIpRuleMaskSrcPort Specifies the per rule mask for the L4 source port as defined in swEgressACLIpRuleSrcPort object.
The value of this object when not in use is the corresponding mask in the profile… | column | OctetString | .1.3.6.1.4.1.171.12.89.3.2.1.15 |
| swEgressACLIpRuleDstPort Specifies the TCP/UDP destination port range.
A value of -1 indicates that this object is not active. | column | Integer32 | .1.3.6.1.4.1.171.12.89.3.2.1.16 |
| swEgressACLIpRuleMaskDstPort Specifies the per rule mask for the L4 destination port as defined in swEgressACLIpRuleDstPort object.
The value of this object when not in use is the corresponding mask in the pr… | column | OctetString | .1.3.6.1.4.1.171.12.89.3.2.1.17 |
| swEgressACLIpRuleFlagBits A value which indicates the set of TCP flags that this
entity may potentially offer. The value is a sum of flag bits.
This sum initially takes the value zero. Then, for each flag,… | column | Integer32 | .1.3.6.1.4.1.171.12.89.3.2.1.18 |
| swEgressACLIpRuleProtoID Specifies that the rule applies to the value of IP protocol ID traffic.
A value of -1 indicates that this object is not active. | column | Integer32 | .1.3.6.1.4.1.171.12.89.3.2.1.19 |
| swEgressACLIpRuleAccessID The ID of the egress ACL rule entry relates to the swEgressACLEtherRuleProfileID.
When row creation is set to 0, this indicates the access ID will be assigned automatically.
When … | column | Integer32 | .1.3.6.1.4.1.171.12.89.3.2.1.2 |
| swEgressACLIpRuleUserDefine Specifies that the rule applies to the first four byte behind the IP header. | column | OctetString | .1.3.6.1.4.1.171.12.89.3.2.1.20 |
| swEgressACLIpRuleUserDefineMask Specifies the per rule mask for the first four byte behind the IP header as defined in
swEgressACLIpRuleUserDefine object. | column | OctetString | .1.3.6.1.4.1.171.12.89.3.2.1.21 |
| swEgressACLIpRuleVID Specifies the VLAN-based rule. There are two conditions:
1. this rule will apply to all the ports;
2. packets must belong to this VLAN.
This object and swEgressACLI… | column | Q-BRIDGE-MIBVlanIdOrNone | .1.3.6.1.4.1.171.12.89.3.2.1.22 |
| swEgressACLIpRulePort Specifies that the access rule will only apply to the port.
This object and swEgressACLIpRuleVID,swEgressACLIpRulePortGroup can not be set together.When you set swEgressACLIpRuleV… | column | Integer32 | .1.3.6.1.4.1.171.12.89.3.2.1.23 |
| swEgressACLIpRulePermit This object indicates if the result of the packet examination is 'permit' or 'deny'.
The default is 'permit'.
deny - Specifies that packets matching the access profile
are … | column | Enumeration | .1.3.6.1.4.1.171.12.89.3.2.1.25 |
| swEgressACLIpRuleEnableReplacePriority Specifies whether the packets that match the access profile will change the
802.1p priority tag field by the switch or not. | column | Enumeration | .1.3.6.1.4.1.171.12.89.3.2.1.26 |
| swEgressACLIpRuleReplacePriority Specifies the priority will change in packets while the swEgressACLIpRuleEnablePriority
is enabled.A value of -1 indicates that this object is not active. | column | Integer32 | .1.3.6.1.4.1.171.12.89.3.2.1.27 |
| swEgressACLIpRuleEnableReplaceDscp Specifies if the switch will change priorities of packets that match the access profile
DSCP field or not. | column | Enumeration | .1.3.6.1.4.1.171.12.89.3.2.1.28 |
| swEgressACLIpRuleReplaceDscp Specifies a value to be written to the DSCP field of an outgoing packet
that meets the criteria specified in the first part of the command.
This value will over-write the value in… | column | Integer32 | .1.3.6.1.4.1.171.12.89.3.2.1.29 |
| swEgressACLIpRuleRowStatus This object indicates the status of this entry. | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.171.12.89.3.2.1.3 |
| swEgressAclIpRuleTimeRangeName Specifies a name of a time-range associated with a specific egress
ACL entry. The time-range name must first be created before being
associated with the access rule. If this name … | column | RFC1213-MIBDisplayString | .1.3.6.1.4.1.171.12.89.3.2.1.30 |
| swEgressACLIpRuleMatchVID Specifies that the access rule will apply only to packets with
this VLAN ID. It is applied to the specified ports configured by swEgressACLIpRulePortGroup.
Note:A value of 0 indic… | column | Q-BRIDGE-MIBVlanIdOrNone | .1.3.6.1.4.1.171.12.89.3.2.1.4 |
| swEgressACLIpMatchVlanMask Specifies the per rule mask for the VLAN as defined in swEgressACLIpRuleVlan object.
The value of this object when not in use is the corresponding mask in the profile mask.
Once t… | column | OctetString | .1.3.6.1.4.1.171.12.89.3.2.1.5 |
| swEgressACLIpRuleSrcIpaddress Specifies an IP source address. | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.171.12.89.3.2.1.6 |
| swEgressACLIpRuleMaskSrcIpaddress Specifies the per rule mask for the source IP address as defined in swEgressACLIpRuleSrcIpaddress object.
The value of this object when not in use is the corresponding mask in the… | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.171.12.89.3.2.1.7 |
| swEgressACLIpRuleDstIpaddress Specifies an IP destination address. | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.171.12.89.3.2.1.8 |
| swEgressACLIpRuleMaskDstIpaddress Specifies the per rule mask for the destination IP address as defined in swEgressACLIpRuleMaskDstIpaddress object.
The value of this object when not in use is the corresponding ma… | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.171.12.89.3.2.1.9 |