portComboForcedMode

ECS4510-MIB · .1.3.6.1.4.1.259.10.1.24.1.2.1.1.12
MIB view Table view

Object

column r/w Enumeration 
This determines the running mode of a fiber port.
For a non-combo port, this variable has a value of none(1),
and setting this variable to none(1) has no effect.
For a combo port, this has its own valid values not
equal to none(1), and setting this variable to none(1) is
not allowed. copperForced(2) is set if user wants to force
this combo port to run in copper mode. copperPreferredAuto(3)
is obsoleted, and user shall not set this state. sfpPreferredAuto(5)
is set if user wants to change copper or fiber mode automatically
by SFP transceiver present state. If SFP transceiver is present,
this combo port will run in fiber mode, and if SFP transceiver is
not present, this combo port will run in copper mode. sfpForced100Fx(6)
is set if user wants to force this fiber port to run in fiber mode with
speed 100Mbps. sfpForced1000Sfp(7) is set if user wants to force this
fiber port to run in fiber mode with speed 1Gbps. sfpForced10gSfp(8) is
set if user wants to force this fiber port to run in fiber mode with
speed 10Gbps.

Context

MIB
ECS4510-MIB
OID
.1.3.6.1.4.1.259.10.1.24.1.2.1.1.12
Type
column
Access
readwrite
Status
current
Parent
portEntry
Table
portTable
Siblings
13

Syntax

Enumeration

Values & Constraints

Enumerated Values
1none
2copperForced
3copperPreferredAuto
4reserved4
5sfpPreferredAuto
6sfpForced100Fx
7sfpForced1000Sfp
8sfpForced10gSfp

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
portIndex
The port and the trunk (including trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by th…
columnIF-MIBInterfaceIndex.1.3.6.1.4.1.259.10.1.24.1.2.1.1.1
portTrunkIndex
The trunk to which this port belongs. A value of 0 means that this port does not belong to any trunk. A value greater than zero means that this port belongs to a trunk in the trun…
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.259.10.1.24.1.2.1.1.10
portMasterSlaveModeCfg
Configures the PHY mode when auto negotiation is disabled and speed-duplex is 1000full for giga copper port.
columnEnumeration.1.3.6.1.4.1.259.10.1.24.1.2.1.1.15
portMacAddrLearningStatus
Set this variable to enabled(1) to start to learn MAC addresses. Set this variable to disabled(2) to stop learning MAC addresses.
columnP-BRIDGE-MIBEnabledStatus.1.3.6.1.4.1.259.10.1.24.1.2.1.1.17
portMacAddrLearningCount
The current number of learned MAC addresses.
columnSNMPv2-SMICounter32.1.3.6.1.4.1.259.10.1.24.1.2.1.1.18
portName
The name of the port or trunk. This is the same as ifAlias in the IF-MIB (RFC2863 or later).
columnOctetString.1.3.6.1.4.1.259.10.1.24.1.2.1.1.2
portType
Indicates the port type of the configuration of the switch.
columnEnumeration.1.3.6.1.4.1.259.10.1.24.1.2.1.1.3
portSpeedDpxCfg
Configures the speed and duplex mode for a port or trunk, according to: halfDuplex10(2) - 10Mbps and half duplex mode fullDuplex10(3) - 10Mbps and full duplex mode …
columnEnumeration.1.3.6.1.4.1.259.10.1.24.1.2.1.1.4
portFlowCtrlCfg
(1) Flow control mechanism is enabled with tx and rx pause mechansim. If the port type is hundredBaseTX or thousandBaseSX: When the port is operating in halfDuplex mode, the port …
columnEnumeration.1.3.6.1.4.1.259.10.1.24.1.2.1.1.5
portCapabilities
Port or trunk capabilities.
columnBits.1.3.6.1.4.1.259.10.1.24.1.2.1.1.6
portAutonegotiation
Whether auto-negotiation is enabled.
columnP-BRIDGE-MIBEnabledStatus.1.3.6.1.4.1.259.10.1.24.1.2.1.1.7
portSpeedDpxStatus
The operating speed and duplex mode of the switched port or trunk. If the entry represents a trunk, the speed is that of its individual members unless the member ports have been i…
columnEnumeration.1.3.6.1.4.1.259.10.1.24.1.2.1.1.8
portFlowCtrlStatus
(2) BackPressure flow control mechanism is used. (3) IEEE 802.3 flow control mechanism is used. (4) Flow control mechanism is disabled. If the entry represents a trunk and the mem…
columnEnumeration.1.3.6.1.4.1.259.10.1.24.1.2.1.1.9