ospfMultiProcessIfAuthKey
ECS4510-MIB ·
.1.3.6.1.4.1.259.10.1.24.1.18.3.14.1.16
Object
column
r/w
OctetString
The cleartext password used as an OSPF authentication key when
simplePassword security is enabled. This object does not access any
OSPF cryptogaphic (e.g., MD5) authentication key under any
circumstance.
If the key length is shorter than 8 octets, th agent will left adjust
and zero fill to 8 octets.
Unauthenticated interfaces need no authentication key, and simple
password authentication cannot us a key of more than 8 octets.
Note that the use of simplePassword authentication is NOT recommended
when there is concern regarding attack upon the OSPF system.
SimplePassword authentication is only sufficient to protect against
accidental misconfigurations because it re-uses cleartext passwords
[RFC1704].
When read, ospfIfAuthKey always returns an octet string of length zero.
This is a private substitution for ospfIfAuthKey of RFC1253.
Context
- MIB
- ECS4510-MIB
- OID
.1.3.6.1.4.1.259.10.1.24.1.18.3.14.1.16- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- ospfMultiProcessIfEntry
- Table
- ospfMultiProcessIfTable
- Siblings
- 19
Syntax
OctetString
Values & Constraints
Object Constraints
range: 0-8
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| ospfMultiProcessIfIpAddressType The IP address type of this OSPF interface. | column | INET-ADDRESS-MIBInetAddressType | .1.3.6.1.4.1.259.10.1.24.1.18.3.14.1.1 |
| ospfMultiProcessIfHelloInterval The length of time, in seconds, between the Hello packets that the
router sends on the interface. This value must be the same for all
routers attached to a common network.
This i… | column | seconds Integer32 | .1.3.6.1.4.1.259.10.1.24.1.18.3.14.1.10 |
| ospfMultiProcessIfRtrDeadInterval The number of seconds that a router's Hello packets have not been seen
before its neighbors declare the router down.
This should be some multiple of the Hello interval. This value… | column | seconds Integer32 | .1.3.6.1.4.1.259.10.1.24.1.18.3.14.1.11 |
| ospfMultiProcessIfState The OSPF Interface State.
This is a private substitution for ospfIfState of RFC1253. | column | Enumeration | .1.3.6.1.4.1.259.10.1.24.1.18.3.14.1.12 |
| ospfMultiProcessIfDesignatedRouter The IP address of the designated router.
This is a private substitution for ospfIfDesignatedRouter of RFC1253. | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.259.10.1.24.1.18.3.14.1.13 |
| ospfMultiProcessIfBackupDesignatedRouter The IP address of the backup designated router.
This is a private substitution for ospfIfBackupDesignatedRouter of
RFC1253. | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.259.10.1.24.1.18.3.14.1.14 |
| ospfMultiProcessIfEvents The number of times this OSPF interface has changed its state or an
error has occurred.
Discontinuities in the value of this counter can occur at
re-initialization … | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.259.10.1.24.1.18.3.14.1.15 |
| ospfMultiProcessIfStatus This variable displays the status of the ospf interface.
Currently only active and notInService statuses are supported.
The value of this object has no effect on wh… | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.259.10.1.24.1.18.3.14.1.17 |
| ospfMultiProcessIfAuthType The authentication type specified for an interface.
Note that this object can be used to engage in significant attacks
against an OSPF router.
This is a private sub… | column | OspfAuthenticationType | .1.3.6.1.4.1.259.10.1.24.1.18.3.14.1.18 |
| ospfMultiProcessIfDesignatedRouterId The Router ID of the designated router.
This is a private substitution for ospfIfDesignatedRouterId of
RFC4750. | column | RouterID | .1.3.6.1.4.1.259.10.1.24.1.18.3.14.1.19 |
| ospfMultiProcessIfIpAddress The IP address of this OSPF interface. | column | INET-ADDRESS-MIBInetAddress | .1.3.6.1.4.1.259.10.1.24.1.18.3.14.1.2 |
| ospfMultiProcessIfBackupDesignatedRouterId The Router ID of the backup designated router.
This is a private substitution for ospfIfBackupDesignatedRouterId
of RFC4750. | column | RouterID | .1.3.6.1.4.1.259.10.1.24.1.18.3.14.1.20 |
| ospfMultiProcessIfCost The output cost of this OSPF interface.
Set 0 means unset the cost, thus the cost is dependent on
ospfMultiProcessAutoCost. | column | Integer32 | .1.3.6.1.4.1.259.10.1.24.1.18.3.14.1.3 |
| ospfMultiProcessIfMtu The mtu of this OSPF interface. Set 0 to unset the mtu. | column | Integer32 | .1.3.6.1.4.1.259.10.1.24.1.18.3.14.1.4 |
| ospfMultiProcessIfMtuIgnore If check(0), OSPF will check the MTU size during DD (Database
Description) exchange.
If ignore(1), OSPF will not check the MTU size during DD exchange. | column | Enumeration | .1.3.6.1.4.1.259.10.1.24.1.18.3.14.1.5 |
| ospfMultiProcessIfAreaId A 32-bit integer uniquely identifying the area to which the interface
connects. Area ID 0.0.0.0 is used for the OSPF backbone.
This is a private substitution for ospfIfAreaId of … | column | AreaID | .1.3.6.1.4.1.259.10.1.24.1.18.3.14.1.6 |
| ospfMultiProcessIfRtrPriority The priority of this interface. Used in multi-access networks, this
field is used in the designated router election algorithm. The value 0
signifies that the router is not eligib… | column | Integer32 | .1.3.6.1.4.1.259.10.1.24.1.18.3.14.1.7 |
| ospfMultiProcessIfTransitDelay The estimated number of seconds it takes to transmit a link state
update packet over this interface. Note that the minimal value SHOULD
be 1 second.
This is a private substitutio… | column | seconds Integer32 | .1.3.6.1.4.1.259.10.1.24.1.18.3.14.1.8 |
| ospfMultiProcessIfRetransInterval The number of seconds between link state advertisement
retransmissions, for adjacencies belonging to this interface. This
value is also used when retransmitting database descripti… | column | seconds Integer32 | .1.3.6.1.4.1.259.10.1.24.1.18.3.14.1.9 |