erpsDomainNodeState
ECS4510-MIB ·
.1.3.6.1.4.1.259.10.1.24.1.62.2.1.13
Object
column
Enumeration
This value displays the node's current state.
It displays one of the following states
(1) init -- The node is in the init state.
(The node state will stay in init state if global status
or domain status is not enabled.)
(2) idle -- The node is in idle state (i.e., no detected
failures, and receiving only 'NR, RB' R-APS frames).
(3) protection -- The node is in protection state.
(4) manualSwitch -- The node is in manual switch state.
(5) forcedSwitch -- The node is in forced switch state.
(6) pending -- The node is in pending state.
Context
- MIB
- ECS4510-MIB
- OID
.1.3.6.1.4.1.259.10.1.24.1.62.2.1.13- Type
- column
- Access
- readonly
- Status
- current
- Parent
- erpsDomainEntry
- Table
- erpsDomainTable
- Siblings
- 34
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | init |
2 | idle |
3 | protection |
4 | manualSwitch |
5 | forcedSwitch |
6 | pending |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| erpsDomainIndex An index that uniquely identifies an entry in the
erpsDomainTable. | column | Integer32 | .1.3.6.1.4.1.259.10.1.24.1.62.2.1.1 |
| erpsDomainHoldoffTimer Configures the value of the holdoff timer which is used to
prevent reporting error event immediately to protection
switching if the provisioned holdoff timer value is non-zero.
Th… | column | Integer32 | .1.3.6.1.4.1.259.10.1.24.1.62.2.1.10 |
| erpsDomainWtrTimer Configures the value of the wait-to-restore timer which is used
by the RPL owner node to prevent frequent switching operations
that may be caused by intermittent failures.
The ran… | column | Integer32 | .1.3.6.1.4.1.259.10.1.24.1.62.2.1.11 |
| erpsDomainControlVlanID This is defined as dot1qVlanIndex in the Q-BRIDGE-MIB.
Configures one control VLAN for each ERPS domain. The control
VLAN is used only to send and receive ERPS message. A control
… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.259.10.1.24.1.62.2.1.12 |
| erpsDomainWestRingPortState This value displays the west ring port's current state.
It displays one of the following states
(1) unknown -- The port's current state is unknown.
(The port's current state w… | column | Enumeration | .1.3.6.1.4.1.259.10.1.24.1.62.2.1.14 |
| erpsDomainEastRingPortState This value displays the east ring port's current state.
It displays one of the following states
(1) unknown -- The port's current state is unknown.
(The port's current state w… | column | Enumeration | .1.3.6.1.4.1.259.10.1.24.1.62.2.1.15 |
| erpsDomainRowStatus The status of this conceptual row entry. This object is used to
manage the creation and deletion of conceptual rows.
The status column has six defined values:
… | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.259.10.1.24.1.62.2.1.16 |
| erpsDomainMajorDomainIndex An index that uniquely identifies an entry in the
erpsDomainTable. A value of 0 means this domain has no major
domain.
Notes: This objest can not be configured if
erpsDomai… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.259.10.1.24.1.62.2.1.17 |
| erpsDomainPropagateTC Set to enabled(1) to transmit topology change signal to the
major domain. It will not take effect,
if erpsDomainMajorDomainIndex has a value of 0. | column | Enumeration | .1.3.6.1.4.1.259.10.1.24.1.62.2.1.18 |
| erpsDomainName The domain name that uniquely identifies an entry in the
erpsDomainTable. | column | OctetString | .1.3.6.1.4.1.259.10.1.24.1.62.2.1.2 |
| erpsDomainWestMepId Configures a CFM Down MEP on west ring port. A down MEP can be
uniquely selected by given a MEPID, domain's MEG level, and
domain's control VLAN ID. A value of 0 means no west MEP… | column | Integer32 | .1.3.6.1.4.1.259.10.1.24.1.62.2.1.20 |
| erpsDomainEastMepId Configures a CFM Down MEP on east ring port. A down MEP can be
uniquely selected by given a MEPID, domain's MEG level, and
domain's control VLAN ID. A value of 0 means no east MEP… | column | Integer32 | .1.3.6.1.4.1.259.10.1.24.1.62.2.1.21 |
| erpsDomainNonErpsDevProtect Set to enabled(1) to use non-standard protection mechanism for
network containing non-ERPS devices. | column | Enumeration | .1.3.6.1.4.1.259.10.1.24.1.62.2.1.22 |
| erpsDomainNodeType Set to none(1) to make this node act as a normal node.
Set to owner(2) to make this node act as an RPL owner.
Set to neighbor(3) to make this node act as an RPL neighbor. | column | Enumeration | .1.3.6.1.4.1.259.10.1.24.1.62.2.1.23 |
| erpsDomainNonRevertive Set to enabled(1) to enable non-revertive mode operation. | column | Enumeration | .1.3.6.1.4.1.259.10.1.24.1.62.2.1.24 |
| erpsDomainRapsDefMac Set to enabled(1) to use R-APS default MAC. | column | Enumeration | .1.3.6.1.4.1.259.10.1.24.1.62.2.1.25 |
| erpsDomainRapsWithoutVc Set to enabled(1) to enable R-APS sub ring without
virtual-channel for a sub domain. | column | Enumeration | .1.3.6.1.4.1.259.10.1.24.1.62.2.1.26 |
| erpsDomainVersion Set to v2(2) to enable ERPS v2 operation. | column | Enumeration | .1.3.6.1.4.1.259.10.1.24.1.62.2.1.27 |
| erpsDomainForcedSwitch Set to west(2) to perform the forced switch command on west
ring port of specified domain.
Set to east(3) to perform the forced switch command on east
ring port of specified domai… | column | Enumeration | .1.3.6.1.4.1.259.10.1.24.1.62.2.1.28 |
| erpsDomainManualSwitch Set to west(2) to perform the manual switch command on west
ring port of specified domain.
Set to east(3) to perform the manual switch command on east
ring port of specified domai… | column | Enumeration | .1.3.6.1.4.1.259.10.1.24.1.62.2.1.29 |
| erpsDomainMegLevel Configures the maintenance entity group (MEG) level which is
used to provide a communication channel for ring automatic
protection switching (R-APS) information. | column | Integer32 | .1.3.6.1.4.1.259.10.1.24.1.62.2.1.3 |
| erpsDomainClear Set to clear(1) to perform the clear command on specified
domain.
The value noClear(2) will always be displayed when reading. | column | Enumeration | .1.3.6.1.4.1.259.10.1.24.1.62.2.1.30 |
| erpsDomainStatsClearAction This variable is used to clear the counters of specified
domain. Set to clear(1) to perform the clear operation.
The value noClear(2) will always be displayed when reading. | column | Enumeration | .1.3.6.1.4.1.259.10.1.24.1.62.2.1.31 |
| erpsDomainWtbTimer Displays the value of the wait-to-block timer in ms
which is used by the RPL owner node when recovering from an
operator command (i.e. FS or MS).
This object will not take effect … | column | Integer32 | .1.3.6.1.4.1.259.10.1.24.1.62.2.1.32 |
| erpsDomainWtbExpire Displays the time remaining in ms until the
wait-to-block timer countdown expires.
A value of 0 means no countdown is running. | column | Integer32 | .1.3.6.1.4.1.259.10.1.24.1.62.2.1.33 |
| erpsDomainWtrExpire Displays the time remaining in seconds until the
wait-to-restore timer countdown expires.
A value of 0 means no countdown is running. | column | Integer32 | .1.3.6.1.4.1.259.10.1.24.1.62.2.1.34 |
| erpsDomainWestRingPortSf This value displays the west ring port's current SF state.
It displays one of the following states
(1) none -- No SF is detected.
(2) detected -- SF is detected. | column | Enumeration | .1.3.6.1.4.1.259.10.1.24.1.62.2.1.35 |
| erpsDomainEastRingPortSf This value displays the east ring port's current SF state.
It displays one of the following states
(1) none -- No SF is detected.
(2) detected -- SF is detected. | column | Enumeration | .1.3.6.1.4.1.259.10.1.24.1.62.2.1.36 |
| erpsDomainMultiRplOwnerWarn This value displays the multiple PPL owner warning state.
It displays one of the following states
(1) none -- No multiple PPL owner warning is detected.
(2) detected -- Multiple R… | column | Enumeration | .1.3.6.1.4.1.259.10.1.24.1.62.2.1.37 |
| erpsDomainNodeId Configures the node id whcih is a MAC address unique to the
ring node. | column | SNMPv2-TCMacAddress | .1.3.6.1.4.1.259.10.1.24.1.62.2.1.4 |
| erpsDomainWestRingPort Each node on the ring connects to the ring through two ports.
As part of the protection switching scheme, one port can be
configured as the west port for the specified domain. The… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.259.10.1.24.1.62.2.1.5 |
| erpsDomainEastRingPort Each node on the ring connects to the ring through two ports.
As part of the protection switching scheme, one port can be
configured as the east port for the specified domain. The… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.259.10.1.24.1.62.2.1.6 |
| erpsDomainRplPort This value displays the port for ring protection link which
under normal conditions, i.e., without any failure or request,
is blocked for traffic channel, to prevent the formation… | column | Enumeration | .1.3.6.1.4.1.259.10.1.24.1.62.2.1.8 |
| erpsDomainGuardTimer Configures the value of the guard timer which is used to
prevent ring nodes from receiving outdated R-APS messages.
The range is in 10 ms steps between 10 ms and 2 seconds,
with a… | column | Integer32 | .1.3.6.1.4.1.259.10.1.24.1.62.2.1.9 |