docsPnmCmtsUsOfdmaAQProbeTimeout
DOCS-PNM-MIB ·
.1.3.6.1.4.1.4491.2.1.27.1.3.3.1.5
Object
column
r/w
seconds Unsigned32
This attribute provides a timeout for the measurement if the CMTS is
unable to perform the measurement for some reason. A value of zero for
the Timeout attribute means that the measurement continues to be active
until the measurement is completed or until the Enable attribute is cleared.
This object cannot be changed while a capture is in progress. It will
return a value of 'inconsistentValue' if set while the value of
'docsPnmCmtsUsOfdmaAQProbeMeasStatus' is set to a value of 'busy'.
Context
- MIB
- DOCS-PNM-MIB
- OID
.1.3.6.1.4.1.4491.2.1.27.1.3.3.1.5- Type
- column
- Access
- readwrite
- Status
- current
- Units
- seconds
- Parent
- docsPnmCmtsUsOfdmaAQProbeEntry
- Table
- docsPnmCmtsUsOfdmaAQProbeTable
- Siblings
- 10
Syntax
seconds Unsigned32
Values & Constraints
Object Constraints
range: 0-65535
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| docsPnmCmtsUsOfdmaAQProbeCmMacAddr This attribute represents the MAC address of the CM transmitting the
probe to be measured.
This object cannot be changed while a capture is in progress. It will
ret… | column | SNMPv2-TCMacAddress | .1.3.6.1.4.1.4491.2.1.27.1.3.3.1.1 |
| docsPnmCmtsUsOfdmaAQProbeMeasStatus This attribute is used to determine the status of the measurement.
When the Status = 'SampleReady', the CCAP has completed the measurement
and the Enable attribute has been cleare… | column | MeasStatusType | .1.3.6.1.4.1.4491.2.1.27.1.3.3.1.10 |
| docsPnmCmtsUsOfdmaAQProbeFileName This attribute is the name of the file, with the captured probe data,
at the CMTS that is to be downloaded using TFTP to the PNM server.
This value can only be chan… | column | SNMP-FRAMEWORK-MIBSnmpAdminString | .1.3.6.1.4.1.4491.2.1.27.1.3.3.1.11 |
| docsPnmCmtsUsOfdmaAQProbeUseIdleSid This attribute, when enabled, causes the CMTS to measure the channel
during a quiet period when no CM is transmitting.
This object cannot be changed while a capture… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4491.2.1.27.1.3.3.1.2 |
| docsPnmCmtsUsOfdmaAQProbePreEqOn This attribute, when enabled, causes the CMTS to enable
pre-equalization in the Probe Information Element for the CM
transmitting the probe to be measured.
This obj… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4491.2.1.27.1.3.3.1.3 |
| docsPnmCmtsUsOfdmaAQProbeEnable This attribute causes the CMTS to begin the measurement of a probe for
the selected CM or for a quiet period if the UseIdleSid attribute is
enabled. The Enable attribute is cleare… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4491.2.1.27.1.3.3.1.4 |
| docsPnmCmtsUsOfdmaAQProbeNumSymToCapt This object represents the number of symbols the CMTS is to capture
for the modem whose probe is being measured or the number of symbol
times to measure for the idle Sid.
… | column | symbols Unsigned32 | .1.3.6.1.4.1.4491.2.1.27.1.3.3.1.6 |
| docsPnmCmtsUsOfdmaAQProbeMaxCaptSymbols This object represents the number of symbols the CMTS can capture for
one measurement. Typically for a 50kHz Subcarrier Spacing the CMTS can
capture two symbols and for 25kHz, the… | column | Unsigned32 | .1.3.6.1.4.1.4491.2.1.27.1.3.3.1.7 |
| docsPnmCmtsUsOfdmaAQProbeNumSamples This object represents the number of FFT samples used for the
measurement. | column | samples Unsigned32 | .1.3.6.1.4.1.4491.2.1.27.1.3.3.1.8 |
| docsPnmCmtsUsOfdmaAQProbeTimeStamp This object represents the timestamp corresponding to the time when the
measurement was performed. In the case in which the Primary Downstream
is an OFDM channel this is the 64 bi… | column | OctetString | .1.3.6.1.4.1.4491.2.1.27.1.3.3.1.9 |