docsPnmCmtsUsImpNoiseMeasStatus

DOCS-PNM-MIB · .1.3.6.1.4.1.4491.2.1.27.1.3.4.1.11

MIB view Table view

Object

column MeasStatusType

This attribute is used to determine the status of the measurement.
When the Status = SampleReady, the CCAP has completed the measurement
and the Enable attribute has been cleared.

Context

MIB: DOCS-PNM-MIB
OID: .1.3.6.1.4.1.4491.2.1.27.1.3.4.1.11
Type: column
Access: readonly
Status: current
Parent: docsPnmCmtsUsImpNoiseEntry
Table: docsPnmCmtsUsImpNoiseTable
Siblings: 11

Syntax

MeasStatusType

Source: MeasStatusType
Base type: Enumeration

Values & Constraints

Type Values

`1`	other
`2`	inactive
`3`	busy
`4`	sampleReady
`5`	error
`6`	resourceUnavailable
`7`	sampleTruncated

Related Objects

Sibling Objects

Object	Type	Syntax	OID
docsPnmCmtsUsImpNoiseEnable This object causes the CMTS to begin the measurement of a probe for the selected CM or for a quiet period if the UseIdleSid attribute is enabled. The Enable attribute is cleared i…	column	SNMPv2-TCTruthValue	`.1.3.6.1.4.1.4491.2.1.27.1.3.4.1.1`
docsPnmCmtsUsImpNoiseLastEvtAvgPwr This attribute represents the average power measured during the last recorded event.	column	dBmV SNMPv2-SMIInteger32	`.1.3.6.1.4.1.4491.2.1.27.1.3.4.1.10`
docsPnmCmtsUsImpNoiseFileName This attribute is the name of the file with the captured impulse noise data at the CMTS that is to be downloaded using TFTP to the PNM server. This value can only b…	column	SNMP-FRAMEWORK-MIBSnmpAdminString	`.1.3.6.1.4.1.4491.2.1.27.1.3.4.1.12`
docsPnmCmtsUsImpNoiseFreeRunDuration This attribute provides length of time to perform the measurement if the StartTriggerLevel is set to zero. This object cannot be changed while a capture is in progr…	column	seconds Unsigned32	`.1.3.6.1.4.1.4491.2.1.27.1.3.4.1.2`
docsPnmCmtsUsImpNoiseStTrigLvl An individual burst event starts when the burst noise exceeds the StartTriggerLevel. If the StartTriggerLevel is set to zero then the free run measurement starts when the Enable i…	column	microvolts SNMPv2-SMIUnsigned32	`.1.3.6.1.4.1.4491.2.1.27.1.3.4.1.3`
docsPnmCmtsUsImpNoiseEndTrigLvl The measurement of an individual burst event ends when the burst noise falls below the EndTriggerLevel. If the StartTriggerLevel is set to zero then the EndTriggerLevel is not use…	column	microvolts SNMPv2-SMIUnsigned32	`.1.3.6.1.4.1.4491.2.1.27.1.3.4.1.4`
docsPnmCmtsUsImpNoiseCenterFrq This attribute defines the center frequency for the noise power measurement. This object cannot be changed while a capture is in progress. It will return a value of…	column	Hz SNMPv2-SMIUnsigned32	`.1.3.6.1.4.1.4491.2.1.27.1.3.4.1.5`
docsPnmCmtsUsImpNoiseMeasBw This attribute defines the bandwidth for the noise power measurement. The MeasurementBw is the -3 dB bandwidth; the occupied bandwidth is typically 1.25 times the measurement band…	column	kHz Unsigned32	`.1.3.6.1.4.1.4491.2.1.27.1.3.4.1.6`
docsPnmCmtsUsImpNoiseNumEvtsCnted This attribute is used to indicate how many impulse noise events have been recorded since the enable was set to true. This value will be 1024 in steady state, after the ring buffe…	column	Unsigned32	`.1.3.6.1.4.1.4491.2.1.27.1.3.4.1.7`
docsPnmCmtsUsImpNoiseLastEvtTimeStamp This attribute provides represents the timestamp corresponding to the start of the last recorded event. The measurement is time-stamped using the 64-bit extended timestamp.	column	OctetString	`.1.3.6.1.4.1.4491.2.1.27.1.3.4.1.8`
docsPnmCmtsUsImpNoiseLastEvtDuration This attribute provides represents the time corresponding to the duration of the last recorded event. The EventDuration is expressed in ns.	column	nanoseconds SNMPv2-SMIUnsigned32	`.1.3.6.1.4.1.4491.2.1.27.1.3.4.1.9`