swIfOperSpeedDuplexAutoNegotiationLocalCapabilities
DLINK-3100-rlInterfaces ·
.1.3.6.1.4.1.171.10.94.89.89.43.1.1.41
Object
column
AutoNegCapabilitiesBits
Operative auto negotiation capabilities of the remote link. unknown bit means that port operative status is not up.
Context
- MIB
- DLINK-3100-rlInterfaces
- OID
.1.3.6.1.4.1.171.10.94.89.89.43.1.1.41- Type
- column
- Access
- readonly
- Status
- current
- Parent
- swIfEntry
- Table
- swIfTable
- Siblings
- 43
Syntax
AutoNegCapabilitiesBits
- Source
- AutoNegCapabilitiesBits
- Base type
Bits
Values & Constraints
Type Values
0 | default |
1 | unknown |
2 | tenHalf |
3 | tenFull |
4 | fastHalf |
5 | fastFull |
6 | gigaHalf |
7 | gigaFull |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| swIfIndex Index to the swIfTable. The interface defined by a
particular value of this index is the same interface as
identified by the same value of ifIndex (MIB II). | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.171.10.94.89.89.43.1.1.1 |
| swIfType This variable specifies the type of interface. | column | Enumeration | .1.3.6.1.4.1.171.10.94.89.89.43.1.1.10 |
| swIfDefaultTag This variable specifies the default VLAN tag which will be attached
to outgoing frames if swIfTaggedMode for this interface is enabled. | column | Integer32 | .1.3.6.1.4.1.171.10.94.89.89.43.1.1.11 |
| swIfDefaultPriority This variable specifies the default port priority. | column | Integer32 | .1.3.6.1.4.1.171.10.94.89.89.43.1.1.12 |
| swIfStatus The status of a table entry.
It is used to delete an entry from this table. | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.171.10.94.89.89.43.1.1.13 |
| swIfFlowControlMode on - Flow control will be enabled on this interface according to the
IEEE 802.3x standard.
off - Flow control is disabled.
autoNegotiation - Flow control will be enabled or disabl… | column | Enumeration | .1.3.6.1.4.1.171.10.94.89.89.43.1.1.14 |
| swIfSpeedAdminMode This variable specifies the required speed of this interface in bits
per second. This specification will take effect only if
swIfSpeedDuplexAutoNegotiation is disabled.
A value of… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.171.10.94.89.89.43.1.1.15 |
| swIfSpeedDuplexAutoNegotiation If enabled the speed and duplex mode will be set by the device through
the autonegotiation process. Otherwise these characteristics will be
set according to the values of swIfSpee… | column | Enumeration | .1.3.6.1.4.1.171.10.94.89.89.43.1.1.16 |
| swIfOperFlowControlMode on - Flow control is enabled on this interface according to the
IEEE 802.3x standard.
off - Flow control is disabled.
enabledRx - Flow control is enabled on this interface for
… | column | Enumeration | .1.3.6.1.4.1.171.10.94.89.89.43.1.1.17 |
| swIfOperSpeedDuplexAutoNegotiation If enabled the speed and duplex are determined by the device through
the autonegotiation process.
If disabled these characteristics are determined according to the values
of swIfS… | column | Enumeration | .1.3.6.1.4.1.171.10.94.89.89.43.1.1.18 |
| swIfOperBackPressureMode This variable indicates the operative back pressure mode of
this interface. | column | Enumeration | .1.3.6.1.4.1.171.10.94.89.89.43.1.1.19 |
| swIfPhysAddressType obsolete This variable indicates whether the physical address assigned to this
interface should be the default one or be chosen from the set of
reserved physical addresses of the device. | column | Enumeration | .1.3.6.1.4.1.171.10.94.89.89.43.1.1.2 |
| swIfAdminLockAction This variable indicates which action this interface should be taken
in locked mode and therefore relevant only in locked mode.
Possible actions:
discard(1) - every packet is dropp… | column | Enumeration | .1.3.6.1.4.1.171.10.94.89.89.43.1.1.20 |
| swIfOperLockAction This variable indicates which action this interface actually takes in
locked mode and therefore relevant only in locked mode.
Possible actions:
discard(1) - every packet is droppe… | column | Enumeration | .1.3.6.1.4.1.171.10.94.89.89.43.1.1.21 |
| swIfAdminLockTrapEnable This variable indicates whether to create a SNMP trap in the locked mode. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.171.10.94.89.89.43.1.1.22 |
| swIfOperLockTrapEnable This variable indicates whether a SNMP trap can be created in the
locked mode. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.171.10.94.89.89.43.1.1.23 |
| swIfOperSuspendedStatus This variable indicates whether the port is suspended or not due to some
feature. After reboot this value is false | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.171.10.94.89.89.43.1.1.24 |
| swIfLockOperTrapCount This variable indicates the trap counter status per ifIndex
(i.e. number of received packets since the last trap sent due to a
packet which was received on this ifIndex). It's rel… | column | Integer32 | .1.3.6.1.4.1.171.10.94.89.89.43.1.1.25 |
| swIfLockAdminTrapFrequency This variable indicates the minimal frequency (in seconds) of sending
a trap per ifIndex. It's relevant only in locked mode and in trap
enabled. | column | Integer32 | .1.3.6.1.4.1.171.10.94.89.89.43.1.1.26 |
| swIfReActivate This variable reactivates (enables) an ifIndex (which was suspended) | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.171.10.94.89.89.43.1.1.27 |
| swIfAdminMdix The configuration is on a physical port, not include trunks.
cross - The interface should force crossover.
normal - The interface should not force crossover.
auto - Auto mdix … | column | Enumeration | .1.3.6.1.4.1.171.10.94.89.89.43.1.1.28 |
| swIfOperMdix cross - The interface is in crossover mode.
normal - The interface is not in crossover mode.
unknown - Only for port that its operative status is not present
or down. | column | Enumeration | .1.3.6.1.4.1.171.10.94.89.89.43.1.1.29 |
| swIfDuplexAdminMode This variable specifies whether this interface should operate in
half duplex or full duplex mode. This specification will take effect
only if swIfSpeedDuplexAutoNegotiation is dis… | column | Enumeration | .1.3.6.1.4.1.171.10.94.89.89.43.1.1.3 |
| swIfHostMode This variable indicates the 802.1X host mode of a port. Relevant when the port's 802.1X control is auto.
In addtion multiple-auth was added. | column | Enumeration | .1.3.6.1.4.1.171.10.94.89.89.43.1.1.30 |
| swIfSingleHostViolationAdminAction This variable indicates which action this interface should take in single authorized.
Possible actions:
discard - every packet is dropped.
forwardNormal - every packet is forwarde… | column | Enumeration | .1.3.6.1.4.1.171.10.94.89.89.43.1.1.31 |
| swIfSingleHostViolationOperAction This variable indicates which action this interface actually takes in single authorized.
Possible actions:
discard(1) - every packet is dropped.
forwardNormal(2) - every packet is… | column | Enumeration | .1.3.6.1.4.1.171.10.94.89.89.43.1.1.32 |
| swIfSingleHostViolationAdminTrapEnable This variable indicates whether to create a SNMP trap in single authorized. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.171.10.94.89.89.43.1.1.33 |
| swIfSingleHostViolationOperTrapEnable This variable indicates whether a SNMP trap can be created in the single authorized. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.171.10.94.89.89.43.1.1.34 |
| swIfSingleHostViolationOperTrapCount This variable indicates the trap counter status per ifIndex
(i.e. number of received packets since the last trap sent due to a packet
which was received on this ifIndex). It's rel… | column | Integer32 | .1.3.6.1.4.1.171.10.94.89.89.43.1.1.35 |
| swIfSingleHostViolationAdminTrapFrequency This variable indicates the minimal frequency (in seconds) of sending a
trap per ifIndex. It's relevant only in single authorized and in trap enabled. | column | Integer32 | .1.3.6.1.4.1.171.10.94.89.89.43.1.1.36 |
| swIfLockLimitationMode This variable indicates what is the learning limitation on the locked interface.
Possible values:
disabled - learning is stopped. The dynamic addresses associated with the
por… | column | Enumeration | .1.3.6.1.4.1.171.10.94.89.89.43.1.1.37 |
| swIfLockMaxMacAddresses This variable defines the maximum number of dynamic addresses that
can be asscoiated with the locked interface. It isn't relevant in
disabled limitation mode. | column | Integer32 | .1.3.6.1.4.1.171.10.94.89.89.43.1.1.38 |
| swIfLockMacAddressesCount This variable indicates the actual number of dynamic addresses that can
be asscoiated with the locked interface. It isn't relevant in disabled
limitation mode. | column | Integer32 | .1.3.6.1.4.1.171.10.94.89.89.43.1.1.39 |
| swIfDuplexOperMode This variable indicates whether this interface operates in half
duplex or full duplex mode.
This variable can have the values hybrid or unknown
only for a trunk.
unknown - only if… | column | Enumeration | .1.3.6.1.4.1.171.10.94.89.89.43.1.1.4 |
| swIfAdminSpeedDuplexAutoNegotiationLocalCapabilities Administrative auto negotiation capabilities of the interface that can be advertised when
swIfSpeedDuplexAutoNegotiation is enabled.
default bit means advertise all the port's cap… | column | AutoNegCapabilitiesBits | .1.3.6.1.4.1.171.10.94.89.89.43.1.1.40 |
| swIfSpeedDuplexNegotiationRemoteCapabilities Operative auto negotiation capabilities of the remote link.
unknown bit means that port operative status is not up,
or auto negotiation process not complete,
or remote link is not… | column | AutoNegCapabilitiesBits | .1.3.6.1.4.1.171.10.94.89.89.43.1.1.42 |
| swIfAdminComboMode This variable specifies the administrative mode of a combo Ethernet interface. | column | Enumeration | .1.3.6.1.4.1.171.10.94.89.89.43.1.1.43 |
| swIfOperComboMode This variable specifies the operative mode of a combo Ethernet interface. | column | Enumeration | .1.3.6.1.4.1.171.10.94.89.89.43.1.1.44 |
| swIfBackPressureMode This variable indicates whether this interface activates back pressure
when congested. | column | Enumeration | .1.3.6.1.4.1.171.10.94.89.89.43.1.1.5 |
| swIfTaggedMode If enable, this interface operates in tagged mode, i.e all frames sent
out through this interface will have the 802.1Q header.
If disabled the frames will not be tagged. | column | Enumeration | .1.3.6.1.4.1.171.10.94.89.89.43.1.1.6 |
| swIfTransceiverType This variable indicates the transceiver type of this interface. | column | Enumeration | .1.3.6.1.4.1.171.10.94.89.89.43.1.1.7 |
| swIfLockAdminStatus This variable indicates whether this interface should operate in locked
or unlocked mode.
In unlocked mode the device learns all MAC addresses from this port and
forwards all fram… | column | Enumeration | .1.3.6.1.4.1.171.10.94.89.89.43.1.1.8 |
| swIfLockOperStatus This variable defines whether this interface operates in locked
or unlocked mode. It is locked in each of the following two cases:
1) if swLockAdminStatus is set to locked
… | column | Enumeration | .1.3.6.1.4.1.171.10.94.89.89.43.1.1.9 |