ospfPmIfMultiAreaIPMaxPktSize
DC-OSPF-MIB ·
.1.3.6.1.4.1.629.10.3.1.28.1.20
Object
column
SNMPv2-SMIInteger32
Maximum transfer unit (MTU) for the interface.
This is the maximum packet size in bytes for packets sent
over the network interface. This size excludes link layer
headers but includes IP headers and higher-level headers.
Normally, DC-OSPF will limit sent PDUs (protocol data
units) to less than or equal to this size. However, if
DC-OSPF cannot construct a valid OSPF PDU smaller than or
equal to this size then it will send the smallest valid
PDU and assume that the IP stack will fragment the packet.
Set to zero if unknown.
Context
- MIB
- DC-OSPF-MIB
- OID
.1.3.6.1.4.1.629.10.3.1.28.1.20- Type
- column
- Access
- readonly
- Status
- current
- Parent
- ospfPmMultiAreaIfEntry
- Table
- ospfPmMultiAreaIfTable
- Siblings
- 27
Syntax
SNMPv2-SMIInteger32
- Source
- SNMPv2-SMIInteger32
- Base type
Integer32
Values & Constraints
Type Constraints
range: -2147483648..2147483647
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| ospfPmMultiAreaIfApplIndex Identifies the DC-OSPF entity. | column | OspfPmIndex | .1.2.826.0.1.1578918.5.62.1.1.28.1.1 |
| ospfPmMultiAreaIfEvents The number of times this OSPF multi-area interface has
changed its state, or an error has occurred. | column | SNMPv2-SMICounter32 | .1.2.826.0.1.1578918.5.62.1.1.28.1.10 |
| ospfPmMultiAreaIfMetricValue The metric assigned to this interface. | column | SNMPv2-SMIInteger32 | .1.2.826.0.1.1578918.5.62.1.1.28.1.11 |
| ospfPmMultiAreaIfTransitDelay The estimated number of seconds it takes to transmit a
link state update packet over this interface. | column | UpToMaxAge | .1.2.826.0.1.1578918.5.62.1.1.28.1.12 |
| ospfPmMultiAreaIfRetransInt The number of seconds between link-state advertisement
retransmissions, for adjacencies belonging to this
interface. This value is also used when retransmitting
database descript… | column | UpToMaxAge | .1.2.826.0.1.1578918.5.62.1.1.28.1.13 |
| ospfPmMultiAreaIfHelloInt The length of time, in seconds, between the Hello packets
that the router sends on the interface. This value must
be the same for the neighbor at the other end of the
multi-area … | column | HelloRange | .1.2.826.0.1.1578918.5.62.1.1.28.1.14 |
| ospfPmMultiAreaIfRtrDeadInt The number of seconds that a router's Hello packets have
not been seen before it's neighbors declare the router
down. This should be some multiple of the Hello interval.
This val… | column | PositiveInteger | .1.2.826.0.1.1578918.5.62.1.1.28.1.15 |
| ospfPmMultiAreaIfFastHelloMult The number of Hellos that should be sent within 1 second
when using Fast Hellos on this interface. This value does
not have to be same for all routers attached to a common
networ… | column | FastHelloMultiplierRange | .1.2.826.0.1.1578918.5.62.1.1.28.1.16 |
| ospfPmMultiAreaIfAuthType The authentication type specified for this interface.
Additional authentication types may be assigned locally.
Note that this object can be used to engage in signif… | column | OspfAuthTypes | .1.2.826.0.1.1578918.5.62.1.1.28.1.17 |
| ospfPmMultiAreaIfAuthKey The cleartext password used as an OSPF Authentication key
when simplePassword security is enabled. This object does
not access any OSPF Cryptogaphic (e.g. MD5)
Authentication Ke… | column | OctetString | .1.2.826.0.1.1578918.5.62.1.1.28.1.18 |
| ospfPmMultiAreaIfAuthUserData Authentication user data for interface level
authentication.
This data is passed opaquely to the Metaswitch
authentication interface where it can be used to assist
… | column | DC-MASTER-TCAuthUserDataString512 | .1.2.826.0.1.1578918.5.62.1.1.28.1.19 |
| ospfPmMultiAreaIfIpAddress The IP address of the primary OSPF interface that this
multi-area interface relates to. | column | SNMPv2-SMIIpAddress | .1.2.826.0.1.1578918.5.62.1.1.28.1.2 |
| ospfPmMultiAreaIfMtuIgnore This object controls whether DC-OSPF checks the MTU size
on incoming Database Description packets. By default, if
the received MTU size in a DB Description packet is higher
than … | column | SNMPv2-TCTruthValue | .1.2.826.0.1.1578918.5.62.1.1.28.1.21 |
| ospfPmMultiAreaIfLsaCount The total number of link-local link state advertisements
in this interface's link-local link state database. | column | SNMPv2-SMIGauge32 | .1.2.826.0.1.1578918.5.62.1.1.28.1.22 |
| ospfPmMultiAreaIfLsaCksumSum The 32-bit unsigned sum of the link-state advertisements'
LS checksums contained in this multi-area interface's
link-local link state database. The sum can be used to
determine i… | column | SNMPv2-SMIUnsigned32 | .1.2.826.0.1.1578918.5.62.1.1.28.1.23 |
| ospfPmMultiAreaIfTrsmtTmrDelay The time this interface will delay a LSU packet, in order
to add more LSAs to the packet before sending. Setting
this correctly can reduce the network traffic. This is
configura… | column | SNMPv2-SMIInteger32 | .1.2.826.0.1.1578918.5.62.1.1.28.1.24 |
| ospfPmMultiAreaIfEnableTeFlood Used to enable TE LSA flooding across this interface.
This allows the TE data network to be partitioned
separately from the underlying OSPF control plane network.
This flag has no… | column | SNMPv2-TCTruthValue | .1.2.826.0.1.1578918.5.62.1.1.28.1.25 |
| ospfPmMultiAreaIfStatsReset Set this object to 'true' to reset all stats counters in the
ospfPmMaIfStatsTable that augments this table.
Reading the value of this object has no meaning. | column | SNMPv2-TCTruthValue | .1.2.826.0.1.1578918.5.62.1.1.28.1.26 |
| ospfPmMultiAreaGraceLsaRsndTmr The value of the timer used to resend Grace LSA packets in
seconds. Following an unplanned restart Grace LSAs are
resent every unplnd_grace_lsa_resend_timer seconds.
… | column | seconds SNMPv2-SMIInteger32 | .1.2.826.0.1.1578918.5.62.1.1.28.1.27 |
| ospfPmMultiAreaGRDelayTimer The value of the timer used to wait, after an unplanned
graceful restart, before sending the first HELLO.
If grace LSAs are being retransmitted, the retransmissions
are stopped wh… | column | seconds SNMPv2-SMIInteger32 | .1.2.826.0.1.1578918.5.62.1.1.28.1.28 |
| ospfPmMultiAreaIfAddressLessIf For the purpose of easing the instancing of addressed and
address less interfaces; This variable takes the value 0
when the related primary interface has an IP Address,
otherwise … | column | IF-MIBInterfaceIndexOrZero | .1.2.826.0.1.1578918.5.62.1.1.28.1.3 |
| ospfPmMultiAreaIfAreaId A 32-bit integer uniquely identifying the area to which
this multi-area interface connects. Area ID 0.0.0.0 is
used for the OSPF backbone. | column | AreaID | .1.2.826.0.1.1578918.5.62.1.1.28.1.4 |
| ospfPmMultiAreaIfRemoteAddr The IP address to which packets for this multi-area
interface should be sent.
On point-to-point interfaces there is no need to configure
the remote address to send … | column | SNMPv2-SMIIpAddress | .1.2.826.0.1.1578918.5.62.1.1.28.1.5 |
| ospfPmMultiAreaIfStatus The row status for this entry, used to create and destroy
an entry in this table. | column | SNMPv2-TCRowStatus | .1.2.826.0.1.1578918.5.62.1.1.28.1.6 |
| ospfPmMultiAreaIfAdminStat The interface's administrative status. The value of this
field indicates whether the OSPF protocol will be run over
this interface and whether this interface will be
advertised a… | column | OspfPmAdminStatus | .1.2.826.0.1.1578918.5.62.1.1.28.1.7 |
| ospfPmMultiAreaIfOperStatus The current operational state of this interface. Note
that a multi-area interface cannot go operationally up
until the corresponding primary interface is operationally
up. | column | OspfPmOperStatus | .1.2.826.0.1.1578918.5.62.1.1.28.1.8 |
| ospfPmMultiAreaIfState The OSPF Interface State for this multi-area interface. | column | OspfInterfaceStates | .1.2.826.0.1.1578918.5.62.1.1.28.1.9 |