bgpPeergrTtlSecurityMinTtl
DC-BGP-MIB ·
.1.2.826.42.1.1578918.5.65.1.5.7.1.68
Object
The minimum TTL (for IPv4) or Hop Limit (for IPv6) that
must be set in a BGP packet received from this peer. This
field is used to enable the Generalized TTL Security
Mechanism (GTSM), as defined in RFC 5082.
If set to 0, then no restriction is applied to received
packets (that is, GTSM is not enabled).
If set to any other value, then packets received from a
peer with a TTL or Hop Limit less than the specified value
will be dropped. A non-zero value also means that DC-BGP
will send packets to this peer with TTL set to 255, as
specified in RFC 5082. This overrides the TTL value
specified in bgpPeerTtl or bgpPeergrTtl.
Note that the typical use case for GTSM is for directly
connected peers, where this field should be set to 254.
Non-directly connected peers may still use this feature,
with a lower value for this field, but the value must be
chosen such that changes in the network topology do not
cause packets to be dropped incorrectly.
This field can be changed at any time. However, if a peer
is configured to use the peer group field and the field is
changed while the peer is active, depending on the setting
of the bgpPeergrResetPeerOnCfgChange field, the peer
session may either be immediately reset, or the
configuration change is not applied until the peer session
is restarted.
Context
- MIB
- DC-BGP-MIB
- OID
.1.2.826.42.1.1578918.5.65.1.5.7.1.68- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- bgpPeergrEntry
- Table
- bgpPeergrTable
- Siblings
- 69
Syntax
SNMPv2-SMIInteger32
- Source
- SNMPv2-SMIInteger32
- Base type
Integer32
Values & Constraints
Type Constraints
range: -2147483648..2147483647
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| bgpPeergrNxtHopSlf Whether or not the peer group has next hop self
configured.
This field overrides the peer bgpPeerNxtHopSlf field.
For an individual AFI-SAFI, if the
… | column | BgpNextHopSelf | .1.2.826.42.1.1578918.5.65.1.5.7.1.10 |
| bgpPeergrThirdPtyNxtHop Whether or not the local BGP speaker should advertise
routes received from this peer group using third party
next hop (this is optional behaviour described in the BGP
specificatio… | column | SNMPv2-TCTruthValue | .1.2.826.42.1.1578918.5.65.1.5.7.1.11 |
| bgpPeergrNxtHopPeer Whether or not the local BGP speaker should override the
use of third party next hop by an EBGP peer. If an EBGP
peer speaker uses third party next hop, routes learnt from
the pe… | column | SNMPv2-TCTruthValue | .1.2.826.42.1.1578918.5.65.1.5.7.1.12 |
| bgpPeergrEnableAttributeDiscard This value indicates whether or not the 'attribute
discard' error handling mechanism is used for BGP UPDATE
messages received from peers in this peer group. This
mechanism applie… | column | SNMPv2-TCTruthValue | .1.2.826.42.1.1578918.5.65.1.5.7.1.13 |
| bgpPeergrSendComm This value indicates whether or not to send BGP community
attributes to peers in this peer group.
When set to 'true', and bgpPeergrAfiSafiSendComm for the
relevant … | column | SNMPv2-TCTruthValue | .1.2.826.42.1.1578918.5.65.1.5.7.1.14 |
| bgpPeergrSendExtComm This value indicates whether or not to send BGP extended
community attributes to peers in this peer group.
When set to 'true', and bgpPeergrAfiSafiSendExtComm for
t… | column | SNMPv2-TCTruthValue | .1.2.826.42.1.1578918.5.65.1.5.7.1.15 |
| bgpPeergrPassword The MD5 password used by peers in this peer group.
For individual peers, this can be configured using
bgpPeerPassword.
This value is passed to the so… | column | OctetString | .1.2.826.42.1.1578918.5.65.1.5.7.1.16 |
| bgpPeergrReflectorClient This value indicates whether peers in this peer group are
reflector clients of this router, or not.
For individual peers, this can be configured using
bgpPeerReflec… | column | BgpPeerReflectorClientType | .1.2.826.42.1.1578918.5.65.1.5.7.1.17 |
| bgpPeergrHoldTimeConfigd Time interval in seconds for the Hold Time configured for
this BGP speaker with peers in this peer group.
For individual peers, this can be configured using
bgpPeer… | column | Unsigned32 | .1.2.826.42.1.1578918.5.65.1.5.7.1.18 |
| bgpPeergrKeepAliveConfigd Time interval in seconds for the KeepAlive configured for
this BGP speaker with peers in this peer group.
For individual peers, this can be configured using
bgpPeer… | column | Unsigned32 | .1.2.826.42.1.1578918.5.65.1.5.7.1.19 |
| bgpPeergrIndex The index of this bgpPeergrEntry. This is the index of the
peer group. | column | SNMPv2-SMIUnsigned32 | .1.2.826.42.1.1578918.5.65.1.5.7.1.2 |
| bgpPeergrTtl The Time To Live used by the connection on peers in this
peer group.
For individual peers, this can be configured using
bgpPeerTtl.
Directly connecte… | column | SNMPv2-SMIInteger32 | .1.2.826.42.1.1578918.5.65.1.5.7.1.20 |
| bgpPeergrMinRteAdvertiseInterval Time interval in seconds for the
MinRouteAdvertisementInterval timer for peers in this peer
group.
For individual peers, this can be configured using
bgpPeerMinRout… | column | Unsigned32 | .1.2.826.42.1.1578918.5.65.1.5.7.1.21 |
| bgpPeergrMinRteWithdrawInterval Time interval in seconds for the MinRouteWithdrawInterval
timer for peers in this peer group.
For individual peers, this can be configured using
bgpPeerMinRouteWith… | column | Unsigned32 | .1.2.826.42.1.1578918.5.65.1.5.7.1.22 |
| bgpPeergrConfigMaxPrfx This object is used in conjunction with the address-family
specific bgpPeergrAfiSafiConfigMaxPrfx to limit the number
of prefixes that can be accepted from peers in this peer
grou… | column | SNMPv2-SMIInteger32 | .1.2.826.42.1.1578918.5.65.1.5.7.1.23 |
| bgpPeergrConfAltLocalAs An alternative local AS number that can be used to
establish a session with peers in this peer group. This
is used when merging two ASs into a single AS.
For indiv… | column | BgpAutonomousSystemNumber | .1.2.826.42.1.1578918.5.65.1.5.7.1.24 |
| bgpPeergrWeight This value defines the weight to be applied to routes
received from neighbors in this group.
All routes learned from neighbors in this group will have
the assigned … | column | SNMPv2-SMIInteger32 | .1.2.826.42.1.1578918.5.65.1.5.7.1.25 |
| bgpPeergrFallover This value indicates whether or not to monitor the route to
the peers in this group so that the session can be
deactivated if the route fails. Monitoring the route means
DC-BGP w… | column | BgpTrueFalseOrInherit | .1.2.826.42.1.1578918.5.65.1.5.7.1.26 |
| bgpPeergrRemoteAs The remote autonomous system number.
For individual peers, this can be configured using
bgpPeerRemoteAs.
This field can be changed at any time. Howe… | column | BgpAutonomousSystemNumber | .1.2.826.42.1.1578918.5.65.1.5.7.1.27 |
| bgpPeergrCheckFirstAsNum Whether or not the first AS number in the AS_PATH
attribute in an UPDATE received from this peer should be
checked to make sure it is the same as the AS number of
the peer. This … | column | BgpTrueFalseOrInherit | .1.2.826.42.1.1578918.5.65.1.5.7.1.28 |
| bgpPeergrConfedMember This value indicates whether or not the peers in this peer
group are members of the same confederation that this
router is in. This field can only be set to true if the
field bgp… | column | SNMPv2-TCTruthValue | .1.2.826.42.1.1578918.5.65.1.5.7.1.29 |
| bgpPeergrRowStatus Used to create and delete a peer group. | column | SNMPv2-TCRowStatus | .1.2.826.42.1.1578918.5.65.1.5.7.1.3 |
| bgpPeergrTrapEstab This value indicates whether or not the Established trap
is used for peers in this peer group.
This field can be changed at any time. However, if a peer
is configu… | column | SNMPv2-TCTruthValue | .1.2.826.42.1.1578918.5.65.1.5.7.1.30 |
| bgpPeergrTrapBackw This value indicates whether or not the Backward
Transition trap is used for peers in this peer group.
This field can be changed at any time. However, if a peer
is… | column | SNMPv2-TCTruthValue | .1.2.826.42.1.1578918.5.65.1.5.7.1.31 |
| bgpPeergrConnectRetryInterval Time interval for the ConnectRetry timer for peers in this
peer group. The suggested value for this timer is 120
seconds.
This field can be changed at any time. H… | column | SNMPv2-SMIUnsigned32 | .1.2.826.42.1.1578918.5.65.1.5.7.1.32 |
| bgpPeergrMinASOriginationInt Time interval in seconds for determining the minimum
amount of time that must elapse between successive
advertisements of UPDATE messages that report changes to a
route within the… | column | Unsigned32 | .1.2.826.42.1.1578918.5.65.1.5.7.1.33 |
| bgpPeergrConfigDropWarn This object is used in conjunction with the address-family
specific bgpPeergrAfiSafiConfigDropWarn to determine
whether the session is dropped or a warning is generated
when the m… | column | BgpDropOrWarn | .1.2.826.42.1.1578918.5.65.1.5.7.1.34 |
| bgpPeergrConfigPassive If TRUE, then no outbound connections will be initiated,
and only incoming connections will be accepted. If FALSE,
then outbound connections will be attempted to peers in
this pe… | column | SNMPv2-TCTruthValue | .1.2.826.42.1.1578918.5.65.1.5.7.1.35 |
| bgpPeergrConfigOpenDelay The delay to enforce in between a TCP connection with
peers in this peer group becoming established and a BGP
Open message being sent. If this delay is zero, then no
delay will b… | column | SNMPv2-SMIUnsigned32 | .1.2.826.42.1.1578918.5.65.1.5.7.1.36 |
| bgpPeergrConfigIdleHold The time to hold peers in this peer group in Idle state
after a BGP session has progressed beyond Idle state
initially and then returned to it. No new connections
will be initiat… | column | SNMPv2-SMIUnsigned32 | .1.2.826.42.1.1578918.5.65.1.5.7.1.37 |
| bgpPeergrCheckNextHop Whether or not to check the BGP next-hop of routes sent to
peers in this peer group. If set to TRUE, which is the
default, then routes with a BGP next-hop which is the same
as th… | column | SNMPv2-TCTruthValue | .1.2.826.42.1.1578918.5.65.1.5.7.1.38 |
| bgpPeergrMaxOrfEntries This object is used in conjunction with the address-family
specific bgpPeergrAfiSafiMaxOrfEntries to limit the number
of ORF entries of all types that can be accepted from
peers i… | column | SNMPv2-SMIUnsigned32 | .1.2.826.42.1.1578918.5.65.1.5.7.1.39 |
| bgpPeergrConfig The index of the Policy Configuration Table this peer
group uses for its policy setup. A value of zero indicates
that the peer group is not associated with any config row.
… | column | SNMPv2-SMIUnsigned32 | .1.2.826.42.1.1578918.5.65.1.5.7.1.4 |
| bgpPeergrPeeringType The type of peering relationship associated with peers in
this peer group. Setting this to 'biLateral' will stop
the advertisement of routes with the NOPEER community to
the peer… | column | BgpPeeringType | .1.2.826.42.1.1578918.5.65.1.5.7.1.40 |
| bgpPeergrDisableRouteRefresh Indicates that DC-BGP should not advertise support for
Route Refresh messages to peers in this peer group.
When this flag is set, DC-BGP will not advertise support
… | column | SNMPv2-TCTruthValue | .1.2.826.42.1.1578918.5.65.1.5.7.1.41 |
| bgpPeergrTrapPrefix Used in conjunction with bgpPeergrAfiSafiTrapPrefix to
determine whether BGP issues an SNMP trap when the number
of prefixes received from peers in this peer group reaches
the max… | column | SNMPv2-TCTruthValue | .1.2.826.42.1.1578918.5.65.1.5.7.1.42 |
| bgpPeergrConfigThreshold A percentage of the limit set by bgpPeergrConfigMaxPrfx.
When the number of prefixes received from peers in this
peer group reaches this threshold, BGP issues a warning.
The actio… | column | SNMPv2-SMIUnsigned32 | .1.2.826.42.1.1578918.5.65.1.5.7.1.43 |
| bgpPeergrMaxPrfxHold The time interval in seconds between when this BGP session
is torn down due to the number of prefixes received from
peers in this peer group exceeding the maximum in
bgpPeergrConf… | column | SNMPv2-SMIUnsigned32 | .1.2.826.42.1.1578918.5.65.1.5.7.1.44 |
| bgpPeergrTrapGrHelperState This value indicates whether or not the Graceful Restart
helper trap is used.
If in use for peers in this peer group, DC-BGP will send a
trap whenever the peer rest… | column | SNMPv2-TCTruthValue | .1.2.826.42.1.1578918.5.65.1.5.7.1.45 |
| bgpPeergrConfAltLocalAsMode This field controls the operation of the alternative local
AS number specified by the bgpPeergrConfAltLocalAs field
for peers in this peer group. It has no effect unless
bgpPeerg… | column | Enumeration | .1.2.826.42.1.1578918.5.65.1.5.7.1.46 |
| bgpPeergrBfdDesired Indicates whether Bidirectional Forwarding Detection (BFD)
is desired for peers in this peer group.
If the NM entity managing the peer session (configured
using bgp… | column | SNMPv2-TCTruthValue | .1.2.826.42.1.1578918.5.65.1.5.7.1.47 |
| bgpPeergrDmzLink If the peer group is for eBGP (as dictated by
bgpPeergrArea), this field indicates that all routes
with IPv4 address family received from peers in this peer
group should have an e… | column | SNMPv2-TCTruthValue | .1.2.826.42.1.1578918.5.65.1.5.7.1.48 |
| bgpPeergrRemovePrivate Whether private AS numbers are removed from the AS path before
sending an update to this peer. This is only relevant for an
eBGP peer. | column | SNMPv2-TCTruthValue | .1.2.826.42.1.1578918.5.65.1.5.7.1.49 |
| bgpPeergrArea Whether this peer group is for IBGP, confederation EBGP,
or EBGP peers. This field can only be changed when the
row is not active. | column | BgpIbgpOrEbgp | .1.2.826.42.1.1578918.5.65.1.5.7.1.5 |
| bgpPeergrAsOverride Whether NBR AS numbers are replaced with Local AS number from
the AS path before sending an update to this peer. This is
only relevant for an eBGP peer. | column | SNMPv2-TCTruthValue | .1.2.826.42.1.1578918.5.65.1.5.7.1.50 |
| bgpPeergrUpdateGroup This field indicates that DC-BGP should treat each
configured peer group for IBGP peers as an update group.
This means that all the peers in the peer group will share
a single Adj… | column | SNMPv2-TCTruthValue | .1.2.826.42.1.1578918.5.65.1.5.7.1.51 |
| bgpPeergrDistListAclIn The Access List index identifying the Access List to use
to filter routes received from peers in this peer group.
If this index is non-zero and the Access List with… | column | SNMPv2-SMIInteger32 | .1.2.826.42.1.1578918.5.65.1.5.7.1.52 |
| bgpPeergrDistListAclOut The Access List index identifying the Access List to use
to filter routes advertised to peers in this peer group.
If this index is non-zero and the Access List with… | column | SNMPv2-SMIInteger32 | .1.2.826.42.1.1578918.5.65.1.5.7.1.53 |
| bgpPeergrDistListPlIn The Prefix List index identifying the Prefix List to use
to filter routes received from peers in this peer group.
If this index is non-zero and the Prefix List with… | column | SNMPv2-SMIInteger32 | .1.2.826.42.1.1578918.5.65.1.5.7.1.54 |
| bgpPeergrDistListPlOut The Prefix List index identifying the Prefix List to use
to filter routes advertised to peers in this peer group.
If this index is non-zero and the Prefix List with… | column | SNMPv2-SMIInteger32 | .1.2.826.42.1.1578918.5.65.1.5.7.1.55 |
| bgpPeergrFilterListIn The Filter List index identifying the Filter List to use
to filter routes received from peers in this peer group.
If this index is non-zero and the Filter List with… | column | SNMPv2-SMIUnsigned32 | .1.2.826.42.1.1578918.5.65.1.5.7.1.56 |
| bgpPeergrFilterListOut The Filter List index identifying the Filter List to use
to filter routes advertised to peers in this peer group.
If this index is non-zero and the Filter List with… | column | SNMPv2-SMIUnsigned32 | .1.2.826.42.1.1578918.5.65.1.5.7.1.57 |
| bgpPeergrAddrSourceIf Interface index for the interface from which the source
address for peer sessions in this group is chosen. If
non-zero, BGP will look for the first address on this
interface with… | column | Unsigned32 | .1.2.826.42.1.1578918.5.65.1.5.7.1.58 |
| bgpPeergrUseImportLocalPref This field defines whether the value in
bgpPeergrImportLocalPref should be used to configure the
local preference value assigned to routes received from
the peers in this group.
… | column | SNMPv2-TCTruthValue | .1.2.826.42.1.1578918.5.65.1.5.7.1.59 |
| bgpPeergrAggrConfedAS This value indicates whether or not the neighbors in the
peer group understand aggregated confederation AS_PATH
information. If set to FALSE, no confederation AS_PATH
information… | column | SNMPv2-TCTruthValue | .1.2.826.42.1.1578918.5.65.1.5.7.1.6 |
| bgpPeergrImportLocalPref Configures the local preference value assigned to routes
received from the peers in this group. This overrides the
value received from the peer.
This field is only… | column | SNMPv2-SMIUnsigned32 | .1.2.826.42.1.1578918.5.65.1.5.7.1.60 |
| bgpPeergrUseExportLocalPref This field defines whether the value in
bgpPeergrExportLocalPref should be used to configure the
local preference value assigned to routes sent to the
peers in this group.
… | column | SNMPv2-TCTruthValue | .1.2.826.42.1.1578918.5.65.1.5.7.1.61 |
| bgpPeergrExportLocalPref Configures the local preference value assigned to routes
being sent to the peers in this group. This overrides the
value already set for the local preference of a route.
… | column | SNMPv2-SMIUnsigned32 | .1.2.826.42.1.1578918.5.65.1.5.7.1.62 |
| bgpPeergrSlowPeer Marks the peers as slow peers.
When update groups are in use, slow peers are kept
separate from other peers to prevent backpressure from the
slow peers slowing down… | column | SNMPv2-TCTruthValue | .1.2.826.42.1.1578918.5.65.1.5.7.1.63 |
| bgpPeergrAddrSourceType The address type of the bgpPeergrAddrSource field. Setting
this field to the default value means that bgpPeergrAddrSource
is unspecified.
This field is ignored for… | column | INET-ADDRESS-MIBInetAddressType | .1.2.826.42.1.1578918.5.65.1.5.7.1.64 |
| bgpPeergrAddrSource If an address is specified with a type matching
bgpPeergrRemoteAddrType, and bgpPeergrAddrSourceIf is NOT
specified, then BGP will use this address as the source
address for the B… | column | INET-ADDRESS-MIBInetAddress | .1.2.826.42.1.1578918.5.65.1.5.7.1.65 |
| bgpPeergrMaxPrfxClear This object is used in conjunction with the address-family
specific bgpPeergrAfiSafiMaxPrfxClear to control when a
bgpPeerAfiSafiMaxPrefixClear trap is sent. This trap will
only … | column | SNMPv2-SMIUnsigned32 | .1.2.826.42.1.1578918.5.65.1.5.7.1.66 |
| bgpPeergrPrfxThresholdClear This object is used in conjunction with the address-family
specific bgpPeergrAfiSafiPrfxThreshClear to control when a
bgpPeerAfiSafiPrfxThrshldClear trap is sent.
This trap will o… | column | SNMPv2-SMIUnsigned32 | .1.2.826.42.1.1578918.5.65.1.5.7.1.67 |
| bgpPeergrRemovePrivateAs Whether private AS numbers are removed from the AS path or
replaced with the local AS number before sending an update to
this peer. This is only relevant for an EBGP peer.
… | column | BgpPrivAsActs | .1.2.826.42.1.1578918.5.65.1.5.7.1.69 |
| bgpPeergrSoftResetWithStoredInfo This object is used in conjunction with
bgpPeergrAfiSafiSoftResetStore to configure 'soft reset
with stored routing information'. This option causes all
routes learned from peers… | column | SNMPv2-TCTruthValue | .1.2.826.42.1.1578918.5.65.1.5.7.1.7 |
| bgpPeergrResetPeerOnCfgChange Certain configuration can only be changed while a peer
session is not active. Setting this field to True will
cause changes to those fields to reset all peer sessions,
so that th… | column | SNMPv2-TCTruthValue | .1.2.826.42.1.1578918.5.65.1.5.7.1.70 |
| bgpPeergrAdminStatus All the peers configured under the peer can be shutdown. | column | BgpAdminStatus | .1.2.826.42.1.1578918.5.65.1.5.7.1.71 |
| bgpPeergrAllowLocalAs The number of instances of the local AS identifier that
may be contained in the route's AS-Path without rejecting
the route.
The AS-Path attribute of a BGP route co… | column | Unsigned32 | .1.2.826.42.1.1578918.5.65.1.5.7.1.8 |
| bgpPeergrDisableSenderLoopDetect This field is used in conjunction with
bgpPeergrAfiSafiDisSndLpDetect to indicate whether BGP
should disable sender-side loop detection when sending
routes to the peer.
… | column | SNMPv2-TCTruthValue | .1.2.826.42.1.1578918.5.65.1.5.7.1.9 |