bgpPeerTtlSecurityMinTtl
DC-BGP-MIB ·
.1.2.826.42.1.1578918.5.65.1.3.1.1.1.131
Object
column
r/w
Integer32
The minimum TTL (for IPv4) or Hop Limit (for IPv6) that
must be set in a BGP packet received from this peer. This
field is used to enable the Generalized TTL Security
Mechanism (GTSM), as defined in RFC 5082.
If set to 0, then no restriction is applied to received
packets (that is, GTSM is not enabled).
If set to any other value, then packets received from a
peer with a TTL or Hop Limit less than the specified value
will be dropped. A non-zero value also means that DC-BGP
will send packets to this peer with TTL set to 255, as
specified in RFC 5082. This overrides the TTL value
specified in bgpPeerTtl or bgpPeergrTttl.
Note that the typical use case for GTSM is for directly
connected peers, where this field should be set to 254.
Non-directly connected peers may still use this feature,
with a lower value for this field, but the value must be
chosen such that changes in the network topology do not
cause packets to be dropped incorrectly.
This field can be changed at any time. However, if the
field is changed while the peer is admin_status UP, the
change will only take effect after the peer has been
cycled admin_status DOWN and then UP, thus forcing the
peer session to be restarted. In this case, until the
peer is set admin_status DOWN, the peer will be marked as
out of date (as reported by the config_state field in the
AMB_BGP_PEER_STATUS row for the peer).
Context
- MIB
- DC-BGP-MIB
- OID
.1.2.826.42.1.1578918.5.65.1.3.1.1.1.131- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- bgpPeerEntry
- Table
- bgpPeerTable
- Siblings
- 130
Syntax
Integer32
Values & Constraints
Object Constraints
range: 0-254
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| bgpPeerLocalNm The entity index of the Neighbor Manager for peering
sessions with this peer.
This field can only be changed when the row is not active.
This field h… | column | SNMPv2-SMIUnsigned32 | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.10 |
| bgpPeerOutPrfxes This field is now deprecated - use bgpPeerStatusOutPrfxes
instead.
The number of prefixes that are installed in all of this
peer's Adj-RIBs-Out.
When… | column | SNMPv2-SMIGauge32 | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.100 |
| bgpPeerOutPrfxesAdvertised This field is now deprecated - use
bgpPeerStatusOutPrfxesAdvertised instead.
The total number of prefixes advertised to this peer.
When additional pa… | column | SNMPv2-SMIGauge32 | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.101 |
| bgpPeerTrapGrHelperState This value indicates whether or not the Graceful Restart
helper trap is used.
If in use for this peer, DC-BGP will send a trap whenever
the peer restart status chan… | column | SNMPv2-TCTruthValue | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.102 |
| bgpPeerEnableAttributeDiscard This value indicates whether or not the 'attribute
discard' error handling mechanism is used for BGP UPDATE
messages received from this peer. This mechanism applies
when a BGP UP… | column | SNMPv2-TCTruthValue | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.103 |
| bgpPeerConfAltLocalAsMode This field controls the operation of the alternative local
AS number specified by the bgpPeerConfAltLocalAs field.
It has no effect unless bgpPeerConfAltLocalAs specifies a
valid … | column | Enumeration | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.104 |
| bgpPeerSendComm This value indicates whether or not to send BGP community
attributes to the peer.
When set to 'true', and bgpPeerAfiSafiSendComm for the
relevant address family is … | column | SNMPv2-TCTruthValue | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.105 |
| bgpPeerSendExtComm This value indicates whether or not to send BGP extended
community attributes to the peer.
When set to 'true', and bgpPeerAfiSafiSendExtComm for the
relevant addres… | column | SNMPv2-TCTruthValue | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.106 |
| bgpPeerConfigUsage A set of bit flags, used together with bgpPeerConfigUsage2
and bgpPeerConfigUsage3, which control where the peer
picks up its configuration from.
A bit flag exists … | column | BgpPeerConfigUsage | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.107 |
| bgpPeerWeight This value defines the weight to be applied to routes
received from this neighbor.
All routes learned from this neighbor will be given this
weight initially. The w… | column | SNMPv2-SMIInteger32 | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.108 |
| bgpPeerFallover This value indicates whether or not to monitor the route to
this peer so that the session can be deactivated if the route
fails. Monitoring the route means DC-BGP will react to
f… | column | BgpTrueFalseOrInherit | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.109 |
| bgpPeerRemoteAddrType The address family of the remote address for the peering
session.
Valid values are: unknown(0), ipv4(1) and ipv6(2).
A type of ipv6 is only accepted … | column | INET-ADDRESS-MIBInetAddressType | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.11 |
| bgpPeerConfigUsage2 A set of bit flags, used together with bgpPeerConfigUsage and
bgpPeerConfigUsage3, which control where the peer picks up its
configuration from.
A bit flag exists f… | column | BgpPeerConfigUsage2 | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.110 |
| bgpPeerDmzLink For an eBGP peer, this field indicates whether all routes
with IPv4 address family received from the peer should
have an extended community attached containing the
bandwidth of th… | column | SNMPv2-TCTruthValue | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.111 |
| bgpPeerRemovePrivate Whether private AS numbers are removed from the AS path before
sending an update to this peer. This is only relevant for an
eBGP peer. | column | SNMPv2-TCTruthValue | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.112 |
| bgpPeerAsOverride Whether Neighbor AS numbers are replaced with the local AS number
from the AS path before sending an update to this peer. This is
only relevant for an eBGP peer. | column | SNMPv2-TCTruthValue | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.113 |
| bgpPeerDistListAclIn The Access List index identifying the Access List to use
to filter routes received from the peer.
If this index is non-zero and the Access List with this
index is d… | column | SNMPv2-SMIInteger32 | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.114 |
| bgpPeerDistListAclOut The Access List index identifying the Access List to use
to filter routes advertised to the peer.
If this index is non-zero and the Access List with this
index is d… | column | SNMPv2-SMIInteger32 | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.115 |
| bgpPeerDistListPlIn The Prefix List index identifying the Prefix List to use
to filter routes received from the peer.
If this index is non-zero and the Prefix List with this
index is d… | column | SNMPv2-SMIInteger32 | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.116 |
| bgpPeerDistListPlOut The Prefix List index identifying the Prefix List to use
to filter routes advertised to the peer.
If this index is non-zero and the Prefix List with this
index is d… | column | SNMPv2-SMIInteger32 | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.117 |
| bgpPeerFilterListIn The Filter List index identifying the Filter List to use
to filter routes received from the peer.
If this index is non-zero and the Filter List with this
index is d… | column | SNMPv2-SMIUnsigned32 | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.118 |
| bgpPeerFilterListOut The Filter List index identifying the Filter List to use
to filter routes advertised to the peer.
If this index is non-zero and the Filter List with this
index is d… | column | SNMPv2-SMIUnsigned32 | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.119 |
| bgpPeerRemoteAddr The remote address for the peering session, or a zero
length field if not specified in which case this peer is
identified only by interface by bgpPeerLocalAddrScopeId.
… | column | OctetString | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.12 |
| bgpPeerAddrSourceIf The interface index for the interface from which the
source address for session is chosen. If non-zero, BGP
will look for the first address on this interface with a
type matching… | column | Unsigned32 | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.120 |
| bgpPeerUseImportLocalPref This field defines whether the value in
bgpPeerImportLocalPref should be used to configure the
local preference value assigned to routes received from
this peer.
Th… | column | SNMPv2-TCTruthValue | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.121 |
| bgpPeerImportLocalPref Configures the local preference value assigned to routes
received from this peer. This overrides the value
received from the peer.
This field is only used if bgpPe… | column | SNMPv2-SMIUnsigned32 | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.122 |
| bgpPeerUseExportLocalPref This field defines whether the value in
bgpPeerExportLocalPref should be used to configure the
local preference value assigned to routes sent to this
peer.
The peer… | column | SNMPv2-TCTruthValue | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.123 |
| bgpPeerExportLocalPref Configures the local preference value assigned to routes
being sent to this peer. This overrides the value already
set for the local preference of a route.
This fi… | column | SNMPv2-SMIUnsigned32 | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.124 |
| bgpPeerSlowPeer Marks the peer as a slow peer.
When update groups are in use, slow peers are kept
separate from other peers to prevent backpressure from the
slow peers slowing down… | column | SNMPv2-TCTruthValue | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.125 |
| bgpPeerConfigUsage3 A set of bit flags, used together with bgpPeerConfigUsage
and bgpPeerConfigUsage2 which control where the peer picks
up its configuration from.
A bit flag exists fo… | column | BgpPeerConfigUsage3 | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.126 |
| bgpPeerAddrSourceType The address type of the bgpPeerAddrSource field. Setting
this field to the default value means that bgpPeerAddrSource
is unspecified.
This field is ignored for pee… | column | INET-ADDRESS-MIBInetAddressType | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.127 |
| bgpPeerAddrSource If an address is specified with a type matching
bgpPeerRemoteAddrType, and bgpPeerAddrSourceIf is NOT
specified, then BGP will use this address as the source
address for the BGP s… | column | INET-ADDRESS-MIBInetAddress | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.128 |
| bgpPeerMaxPrfxClear This object is used in conjunction with the address-family
specific bgpPeerAfiSafiMaxPrfxClear to control when a
bgpPeerAfiSafiMaxPrefixClear trap is sent. This trap will
only be… | column | SNMPv2-SMIUnsigned32 | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.129 |
| bgpPeerRemotePort The remote port configured for the peering session, or
zero if not specified.
For outbound connections, if a remote port is specified
then DC-BGP will connect to th… | column | INET-ADDRESS-MIBInetPortNumber | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.13 |
| bgpPeerPrfxThresholdClear A percentage of the limit set by bgpPeerConfigMaxPrfx.
This object is used in conjunction with the address-family
specific bgpPeerAfiSafiPrfxThrsholdClear to control when a
bgpPee… | column | SNMPv2-SMIUnsigned32 | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.130 |
| bgpPeerRemovePrivateAs Whether private AS numbers are removed from the AS path or
replaced with the local AS number before sending an update to
this peer. This is only relevant for an EBGP peer.
… | column | BgpPrivAsActs | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.132 |
| bgpPeerRemoteAs The remote autonomous system number. This is ignored for
peers that are identified by interface only.
This field can be changed at any time. However, if the
field… | column | BgpAutonomousSystemNumber | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.14 |
| bgpPeerIndex This field is now deprecated - use bgpPeerStatusPeerIndex
instead.
The peer index is a unique index for the peer entry in the
bgpPeerStatusTable. It is used to pro… | column | SNMPv2-SMIUnsigned32 | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.15 |
| bgpPeerConfedMember This value indicates whether or not the peer is a member
of the same confederation that this router is in.
This field can only be set to true if the field
bgpRmEntC… | column | SNMPv2-TCTruthValue | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.16 |
| bgpPeerReflectorClient This value indicates whether the given peer is a reflector
client of this router, or not. A value of nonClient(0)
indicates that this peer is not a reflector client. A
value of … | column | BgpPeerReflectorClientType | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.17 |
| bgpPeerTrapEstab This value indicates whether or not the Established trap
is used.
This field can be changed at any time. However, if the
field is changed while the peer is admin_s… | column | SNMPv2-TCTruthValue | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.18 |
| bgpPeerTrapBackw This value indicates whether or not the Backward
Transition trap is used.
This field can be changed at any time. However, if the
field is changed while the peer is… | column | SNMPv2-TCTruthValue | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.19 |
| bgpPeerIdentifier This field is now deprecated - use bgpPeerStatusIdentifier
instead.
The BGP Identifier of this entry's BGP peer.
This entry is zero unless the bgpPee… | column | BgpIdentifier | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.2 |
| bgpPeerCapsSupport This field is now deprecated - use
bgpPeerStatusCapsSupport instead.
Whether or not this peer accepted our local capabilities
optional parameter sent on the OPEN me… | column | SNMPv2-TCTruthValue | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.20 |
| bgpPeerLastError This field is now deprecated - use bgpPeerStatusLastError
instead.
The last error code and subcode sent or received on this
connection. If no error has occurred, t… | column | OctetString | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.21 |
| bgpPeerLastErrorDataLen This field is now deprecated - use
bgpPeerStatusLastErrorDataLen instead.
The length of the last error data. If this is zero no
error data was provided or generate… | column | Unsigned32 | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.22 |
| bgpPeerLastErrorData This field is now deprecated - use
bgpPeerStatusLastErrorData instead.
The last error code's data seen by this peer on this
connection. | column | OctetString | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.23 |
| bgpPeerFsmEstablishedTime This field is now deprecated - use
bgpPeerStatusFsmEstablishedTime instead.
This timer indicates how long in seconds this peer has
been in the Established state or … | column | seconds SNMPv2-SMIGauge32 | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.24 |
| bgpPeerInUpdatesElapsedTime This field is now deprecated - use
bgpPeerStatusInUpdatesElpsTime instead.
Elapsed time in seconds since the last BGP message was
received from the peer. Each time… | column | seconds SNMPv2-SMIGauge32 | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.25 |
| bgpPeerConnectRetryInterval Time interval for the ConnectRetry timer. The suggested
value for this timer is 120 seconds.
This field can be changed at any time. However, if the
field is chang… | column | seconds Unsigned32 | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.26 |
| bgpPeerHoldTimeConfigd Time interval in seconds for the Hold Time configured for
this BGP speaker with this peer. This value is placed in
an OPEN message sent to this peer by this BGP speaker, and
is c… | column | seconds Unsigned32 | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.27 |
| bgpPeerKeepAliveConfigd Time interval in seconds for the KeepAlive configured for
this BGP speaker with this peer. The value of this object
will only determine the KEEPALIVE messages' frequency
relative… | column | seconds Unsigned32 | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.28 |
| bgpPeerMinASOriginationInterval Time interval in seconds for determining the minimum amount
of time that must elapse between successive advertisements of
UPDATE messages that report changes to a route within the… | column | seconds Unsigned32 | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.29 |
| bgpPeerState This field is now deprecated - use bgpPeerStatusState
instead.
The BGP peer's FSM state. | column | BgpPeerStates | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.3 |
| bgpPeerMinRouteAdvertiseInterval Time interval in seconds for the
MinRouteAdvertisementInterval timer. This determines the
minimum time between a BGP UPDATE to a peer advertising or
withdrawing a route and a sub… | column | seconds Unsigned32 | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.30 |
| bgpPeerHoldTime This field is now deprecated - use bgpPeerStatusHoldTime
instead.
Time interval in seconds for the Hold Timer established with
the peer.
The Hold Tim… | column | seconds Integer32 | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.31 |
| bgpPeerKeepAlive This field is now deprecated - use bgpPeerStatusKeepAlive
instead.
Time interval in seconds for the KeepAlive Timer established
with the peer.
The Ke… | column | seconds Integer32 | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.32 |
| bgpPeerInUpdates This field is now deprecated - use bgpPeerStatusInUpdates
instead.
The number of BGP UPDATE messages received on this
connection. This object is initialized to zer… | column | SNMPv2-SMICounter32 | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.33 |
| bgpPeerOutUpdates This field is now deprecated - use bgpPeerStatusOutUpdates
instead.
The number of BGP UPDATE messages transmitted on this
connection. This object is initialized to… | column | SNMPv2-SMICounter32 | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.34 |
| bgpPeerInTotalMessages This field is now deprecated - use
bgpPeerStatusInTotalMessages instead.
The total number of messages received from the remote peer
on this connection. This object… | column | SNMPv2-SMICounter32 | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.35 |
| bgpPeerOutTotalMessages This field is now deprecated - use
bgpPeerStatusOutTotalMessages instead.
The total number of messages transmitted to the remote
peer on this connection. This obje… | column | SNMPv2-SMICounter32 | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.36 |
| bgpPeerFsmEstablishedTransitions This field is now deprecated - use
bgpPeerStatusFsmEstTransitions instead.
The total number of times the BGP FSM transitioned into
the established state for this pe… | column | SNMPv2-SMICounter32 | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.37 |
| bgpPeerConnectRetryCount This field is now deprecated - use
bgpPeerStatusConnectRetryCount instead.
The current connect retry count of this peer.
This is incremented each tim… | column | SNMPv2-SMICounter32 | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.38 |
| bgpPeerClearCnts This field is now deprecated - use
bgpPeerStatusClearCnts instead.
Set to clear the counters associated with this peer.
Reading the value of this fie… | column | SNMPv2-TCTruthValue | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.39 |
| bgpPeerRowStatus The row status for this BGP peer table entry, used to
create and destroy table entries. | column | SNMPv2-TCRowStatus | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.4 |
| bgpPeerConfigPeergr The index of the peer group this neighbor belongs to, or
zero if this neighbor does not belong to a peer group. | column | SNMPv2-SMIUnsigned32 | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.40 |
| bgpPeerConfigIndex The index of the Policy Configuration Table this peer uses
for its policy setup. This field may be changed when the
peer is admin_status UP. A value of zero indicates that
the p… | column | SNMPv2-SMIUnsigned32 | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.41 |
| bgpPeerConfigRtRefresh This field is now deprecated - use bgpPeerStatusRtRefresh
instead.
Set this field to 'true' to trigger a route refresh for this
peer.
Setting this fi… | column | SNMPv2-TCTruthValue | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.42 |
| bgpPeerConfigMaxPrfx This object is used in conjunction with the address-family
specific bgpPeerAfiSafiConfigMaxPrfx to limit the number of
prefixes that can be accepted from this peer.
… | column | SNMPv2-SMIInteger32 | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.43 |
| bgpPeerConfigDropWarn This object is used in conjunction with the address-family
specific bgpPeerAfiSafiConfigDropWarn to determine whether
the session is dropped or a warning is generated when
the max… | column | BgpDropOrWarn | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.44 |
| bgpPeerConfigPassive If TRUE, then no outbound connections will be initiated,
and only incoming connections will be accepted. If FALSE,
then outbound connections will be attempted to this peer,
and i… | column | SNMPv2-TCTruthValue | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.45 |
| bgpPeerConfigOpenDelay The delay to enforce in between a TCP connection with this
peer becoming established and a BGP Open message being
sent. If this delay is zero, then no delay will be
injected, and… | column | seconds Unsigned32 | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.46 |
| bgpPeerConfigIdleHold The time to hold this peer in Idle state after a BGP
session has progressed beyond Idle state initially and
then returned to it. No new connections will be initiated
or accepted … | column | seconds Unsigned32 | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.47 |
| bgpPeerPassword The MD5 password used by this peer. This value is passed to
the sockets stub at creation. bgpPeerPasswordLen must be
set to the length of the string. This field can only be
cha… | column | OctetString | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.48 |
| bgpPeerTtl The Time To Live used by the connection on this peer.
Directly connected peers should have this set to one. A
value of zero indicates the TTL socket option will not be
set for th… | column | SNMPv2-SMIInteger32 | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.49 |
| bgpPeerAdminStatus The desired state of the BGP connection.
A transition from 'up' to 'down' will cause the BGP Stop
Event to be generated.
A transition from 'down' to… | column | BgpAdminStatus | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.5 |
| bgpPeerCheckFirstAsNum Whether or not the first AS number in the AS_PATH
attribute in an UPDATE received from this peer should be
checked to make sure it is the same as the AS number of
the peer. This … | column | BgpTrueFalseOrInherit | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.50 |
| bgpPeerAggrInclConfedAS This value indicates whether or not the neighbor
understands aggregated confederation AS_PATH information.
If set to FALSE, no confederation AS_PATH information is
included in agg… | column | SNMPv2-TCTruthValue | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.51 |
| bgpPeerMinRouteWithdrawInterval Time interval in seconds for the MinRouteWithdrawInterval
timer. This is the interval which is enforced between
advertisement and subsequent withdrawal of a route.
… | column | seconds Unsigned32 | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.52 |
| bgpPeerStalePathTime This field is now deprecated - use
bgpPeerStatusStalePathTime instead.
The maximum time in seconds that DC-BGP will wait
following a peer restart or peer session fa… | column | seconds SNMPv2-SMIUnsigned32 | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.53 |
| bgpPeerCheckNextHop Whether or not to check the BGP next-hop of routes sent to
this peer. If set to TRUE, which is the default, then
routes with a BGP next-hop which is the same as the peer's
addres… | column | SNMPv2-TCTruthValue | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.54 |
| bgpPeerLocalAddrScopeId For a peer identified by a link-local IPv6 addresses, this
is the scope ID of bgpPeerLocalAddr and bgpPeerRemoteAddr.
For a peer identified only by interface (bgpPe… | column | SNMPv2-SMIUnsigned32 | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.55 |
| bgpPeerMaxOrfEntries This object is used in conjunction with the address-family
specific bgpPeerAfiSafiMaxOrfEntries to limit the number of
ORF entries of all types that can be accepted from this peer… | column | SNMPv2-SMIUnsigned32 | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.56 |
| bgpPeerOrfEntryCount This field is now deprecated - use
bgpPeerStatusOrfEntryCount instead.
The current number of ORF entries of all types that have
been received from the peer. | column | SNMPv2-SMICounter32 | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.57 |
| bgpPeerPeeringType The type of peering relationship associated with this
peer. Setting this to 'biLateral' will stop the
advertisement of routes with the NOPEER community to this
peer, and also fil… | column | BgpPeeringType | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.58 |
| bgpPeerSoftResetWithStoredInfo This object is used in conjunction with
bgpPeerAfiSafiSoftResetStore to configure 'soft reset with
stored routing information'. This option
causes all routes learned from a peer … | column | SNMPv2-TCTruthValue | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.59 |
| bgpPeerOperStatus The current operational status of this peer. This usually
reflects the desired AdminStatus, but can contain transitional
values and failures. | column | BgpOperStatus | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.6 |
| bgpPeerAllowLocalAs The number of instances of the local AS identifier that may
be contained in the route's AS-Path without rejecting the
route.
The AS-Path attribute of a BGP route co… | column | Unsigned32 | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.60 |
| bgpPeerDisableSenderLoopDetect This field is used in conjunction with
bgpPeerAfiSafiDisableSndLpDetect to indicate whether BGP
should disable sender-side loop detection when sending
routes to the peer.
… | column | SNMPv2-TCTruthValue | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.61 |
| bgpPeerDisableRouteRefresh Indicates that DC-BGP should not advertise support for
Route Refresh messages to this peer.
When this flag is set, DC-BGP will not advertise support
for Route Refre… | column | SNMPv2-TCTruthValue | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.62 |
| bgpPeerFlapStatsClearStat This field is now deprecated - use
bgpPeerStatusFlapStatsClearStat instead.
Set this field to 'true' to clear the bgpFlapStatsFlapcnt
in all entries in the bgpNlriT… | column | SNMPv2-TCTruthValue | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.63 |
| bgpPeerFlapStatsClearMap This field is now deprecated - use
bgpPeerStatusFlapStatsClearMap instead.
This field is set with bgpPeerFlapStatsClearStat to
restrict the set of routes for which … | column | SNMPv2-SMIUnsigned32 | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.64 |
| bgpPeerLastErrorRcvd This field is now deprecated - use
bgpPeerStatusLastErrorRcvd instead.
The last error code and subcode received from the peer on
this connection.
If … | column | OctetString | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.65 |
| bgpPeerLastErrorRcvdTime This field is now deprecated - use
bgpPeerStatusLastErrorRcvdTime instead.
The value of sysUpTime when the last error was received
from the peer on this connection.… | column | SNMPv2-TCTimeStamp | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.66 |
| bgpPeerLastErrorSent This field is now deprecated - use
bgpPeerStatusLastErrorSent instead.
The last error code and subcode sent to the peer on this
connection.
If no err… | column | OctetString | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.67 |
| bgpPeerLastErrorSentTime This field is now deprecated - use
bgpPeerStatusLastErrorSentTime instead.
The value of sysUpTime when the last error was sent to the
peer on this connection.
… | column | SNMPv2-TCTimeStamp | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.68 |
| bgpPeerLastState This field is now deprecated - use bgpPeerStatusLastState
instead.
The BGP peer's previous FSM state. | column | BgpPeerStates | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.69 |
| bgpPeerLocalAddrType The address family of the local address configured for the
peering session.
Valid values are: unknown(0), ipv4(1) and ipv6(2).
A type of ipv6 is only… | column | INET-ADDRESS-MIBInetAddressType | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.7 |
| bgpPeerLastEvent This field is now deprecated - use bgpPeerStatusLastEvent
instead.
The last input to be made to the BGP peer's FSM. | column | BgpPeerEvents | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.70 |
| bgpPeerCapsSent This field is now deprecated - use bgpPeerStatusCapsSent
instead.
The capabilities announced to the peer on the most recent
Open message sent to the peer. This fie… | column | BgpCapabilities | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.71 |
| bgpPeerCapsRcvd This field is now deprecated - use bgpPeerStatusCapsRcvd
instead.
The capabilities received on the most recent Open message
received from the peer. This field is s… | column | BgpCapabilities | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.72 |
| bgpPeerCapsNegotiated This field is now deprecated - use
bgpPeerStatusCapsNegotiated instead.
The capabilities negotiated for the session with the peer.
This field is set to zero before … | column | BgpCapabilities | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.73 |
| bgpPeerRstrSupport This field is now deprecated - use
bgpPeerStatusRstrSupport instead.
Whether the peer supports graceful restart. This field is
set to 'none' before an Open message… | column | BgpPeerRestartSupport | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.74 |
| bgpPeerRstrFamily This field is now deprecated - use bgpPeerStatusRstrFamily
instead.
The address and subaddress families for which the peer
supports graceful restart. This field is… | column | BgpAfiSafiBits | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.75 |
| bgpPeerRstrRestarting This field is now deprecated - use
bgpPeerStatusRstrRestarting instead.
Whether the peer is currently in the process of restarting. | column | SNMPv2-TCTruthValue | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.76 |
| bgpPeerRstrStatus This field is now deprecated - use bgpPeerStatusRstrStatus
instead.
The current state of the peer's restart processing. If
bgpPeerRstrRestarting is false, this is … | column | BgpPeerRestartStatus | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.77 |
| bgpPeerRstrRemTime This field is now deprecated - use
bgpPeerStatusRstrRemTime instead.
The time remaining in the current restart state, in
hundredths of a second. If bgpPeerRstrStat… | column | SNMPv2-TCTimeInterval | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.78 |
| bgpPeerRcvdMsgElapsedTime This field is now deprecated - use
bgpPeerStatusRcvdMsgElpsTime instead.
The elapsed time in hundredths of a second since anything
was received from this peer. If … | column | SNMPv2-TCTimeInterval | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.79 |
| bgpPeerLocalAddr The local address configured for the peering session, or
a zero length address if not specified.
For outbound connections, if a local address is specified
then DC-B… | column | OctetString | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.8 |
| bgpPeerIdleHoldRemTime This field is now deprecated - use
bgpPeerStatusIdleHoldRemTime instead.
For a peer in 'idle' state, the time remaining in
hundredths of a second until DC-BGP will … | column | SNMPv2-TCTimeInterval | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.80 |
| bgpPeerRouteRefrSent This field is now deprecated - use
bgpPeerStatusRouteRefrSent instead.
The number of Route Refresh messages sent to the peer. If
the session comes down this value … | column | SNMPv2-SMICounter32 | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.81 |
| bgpPeerRouteRefrRcvd This field is now deprecated - use
bgpPeerStatusRouteRefrRcvd instead.
The number of Route Refresh messages received from the peer.
If the session comes down this v… | column | SNMPv2-SMICounter32 | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.82 |
| bgpPeerNxtHopSlf Whether or not the peer has next hop self configured.
Setting this field to a value other than 'no' causes the
value of bgpPeerThirdPtyNxtHop to be ignored.
… | column | BgpNextHopSelf | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.83 |
| bgpPeerThirdPtyNxtHop Whether or not the local BGP speaker should advertise routes
received from this peer using third party next hop (this is
optional behaviour described in the BGP specification).
… | column | SNMPv2-TCTruthValue | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.84 |
| bgpPeerNxtHopPeer Whether or not the local BGP speaker should override the use
of third party next hop by an EBGP peer. If an EBGP peer
speaker uses third party next hop, routes learnt from the pe… | column | SNMPv2-TCTruthValue | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.85 |
| bgpPeerTrapPrefix Used in conjunction with bgpPeerAfiSafiTrapPrefix to
determine whether BGP issues an SNMP trap when the number of
prefixes received from this peer reaches the maximum number
of pr… | column | SNMPv2-TCTruthValue | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.86 |
| bgpPeerConfigThreshold A percentage of the limit set by bgpPeerConfigMaxPrfx.
When the number of prefixes received from this peer reaches
this threshold, BGP issues a warning. The action carried
out by… | column | Unsigned32 | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.87 |
| bgpPeerMaxPrfxHold The time interval in seconds between when this BGP session
is torn down due to the number of prefixes received from
this peer exceeding the maximum in
bgpPeerConfigMaxPrfx(AfiSafi… | column | Unsigned32 | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.88 |
| bgpPeerSelectedLocalAddrType This field is now deprecated - use
bgpPeerStatusSelLocalAddrType instead.
The address family of the local address used by the
transport connection for the peering s… | column | INET-ADDRESS-MIBInetAddressType | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.89 |
| bgpPeerLocalPort The local port configured for the peering session, or zero
if not specified.
For outbound connections, if a local port is specified
then DC-BGP will bind to the spe… | column | INET-ADDRESS-MIBInetPortNumber | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.9 |
| bgpPeerSelectedLocalAddr This field is now deprecated - use
bgpPeerStatusSelLocalAddr instead.
The local address used by the transport connection for the
peering session.
If … | column | OctetString | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.90 |
| bgpPeerSelectedLocalPort This field is now deprecated - use
bgpPeerStatusSelLocalPort instead.
The local port used by the transport connection for the
peering session.
If a c… | column | INET-ADDRESS-MIBInetPortNumber | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.91 |
| bgpPeerSelectedRemotePort This field is now deprecated - use
bgpPeerStatusSelRemotePort instead.
The remote port used by the transport connection for the
peering session.
If a… | column | INET-ADDRESS-MIBInetPortNumber | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.92 |
| bgpPeerBfdDesired Indicates whether Bidirectional Forwarding Detection (BFD) is
desired for this peer.
If the NM entity managing this peer session (configured using
bgpPeerLocalNm) d… | column | SNMPv2-TCTruthValue | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.93 |
| bgpPeerBfdStatus This field is now deprecated - use bgpPeerStatusBfdStatus
instead.
BFD session state for this peer. | column | DC-MASTER-TCBfdSessionStatus | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.94 |
| bgpPeerCeaseErrorSubcode This field is now deprecated - use
bgpPeerStatusCeaseErrorSubcode instead.
The error subcode to be sent in the Cease Notification
messages triggered by MIB requests… | column | BgpCeaseErrorSubcode | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.95 |
| bgpPeerConfAltLocalAs An alternative local AS number that can be used to
establish a session with this peer. This is used when
merging two ASs into a single AS.
A value of zero means 'n… | column | BgpAutonomousSystemNumber | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.96 |
| bgpPeerSelectedLocalAs This field is now deprecated - use bgpPeerStatusSelLocalAs
instead.
The local AS number used on this session.
If bgpPeerConfAltLocalAs is set to a no… | column | BgpAutonomousSystemNumber | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.97 |
| bgpPeerSelectedRemoteAs This field is now deprecated - use
bgpPeerStatusSelRemoteAs instead.
The remote AS number used on this session.
If bgpPeerConfAltLocalAs is set to a … | column | BgpAutonomousSystemNumber | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.98 |
| bgpPeerInPrfxes This field is now deprecated - use bgpPeerStatusInPrfxes
instead.
The total number of prefixes received from this peer.
When additional paths are ena… | column | SNMPv2-SMIGauge32 | .1.2.826.42.1.1578918.5.65.1.3.1.1.1.99 |