f100IIrlModeLocal
CTC-FRM220-MIB ·
.1.3.6.1.4.1.4756.20.60.20.1.26
Object
column
r/w
Enumeration
Local FRM220-10/100I card Ingress Rate Limit mode: 0:No limit 1:n x 32K 2:n x 512K
Context
- MIB
- CTC-FRM220-MIB
- OID
.1.3.6.1.4.1.4756.20.60.20.1.26- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- f100ILocalEntry
- Table
- f100ILocalTable
- Siblings
- 56
Syntax
Enumeration
Values & Constraints
No enumerated values or constraints recorded.
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| f100IChassisIndexLocal A unique value for each local card.
It is the chassis location number. | column | Integer32 | .1.3.6.1.4.1.4756.20.60.20.1.1 |
| f100IUtpRxActLocal Local FRM220-10/100I card UTP receive active status:
0:Off
1:On | column | Enumeration | .1.3.6.1.4.1.4756.20.60.20.1.10 |
| f100IUtpNegoLocal Local FRM220-10/100I card UTP negotiation status:
0:Manual
1:Auto | column | Enumeration | .1.3.6.1.4.1.4756.20.60.20.1.11 |
| f100IUtpSpeedLocal Local FRM220-10/100I card UTP speed:
0:10MHz
1:100MHz | column | Enumeration | .1.3.6.1.4.1.4756.20.60.20.1.12 |
| f100IUtpDuplexLocal Local FRM220-10/100I card UTP duplex:
0:Half duplex mode
1:Full duplex mode | column | Enumeration | .1.3.6.1.4.1.4756.20.60.20.1.13 |
| f100IUtpSpeedStatusLocal Local FRM220-10/100I card UTP speed status:
0:10MHz
1:100MHz | column | Enumeration | .1.3.6.1.4.1.4756.20.60.20.1.14 |
| f100IUtpDuplexStatusLocal Local FRM220-10/100I card UTP duplex status:
0:Half duplex mode
1:Full duplex mode | column | Enumeration | .1.3.6.1.4.1.4756.20.60.20.1.15 |
| f100IUtpRxByteLocal Local FRM220-10/100I card UTP-in octet counter | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.4756.20.60.20.1.16 |
| f100IUtpTxByteLocal Local FRM220-10/100I card UTP-out octet counter | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.4756.20.60.20.1.17 |
| f100IUtpFnlRxByteLocal Local FRM220-10/100I card UTP-in final octets | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.4756.20.60.20.1.18 |
| f100IUtpFnlTxByteLocal Local FRM220-10/100I card UTP-out final octets | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.4756.20.60.20.1.19 |
| f100ISlotIndexLocal A unique value for each local card.
It is the slot location number. | column | Integer32 | .1.3.6.1.4.1.4756.20.60.20.1.2 |
| f100IFxLinkLocal Local FRM220-10/100I card fiber link status:
0:Down
1:Up | column | Enumeration | .1.3.6.1.4.1.4756.20.60.20.1.20 |
| f100IFxRxActLocal Local FRM220-10/100I card fiber receiver active status:
0:Off
1:On | column | Enumeration | .1.3.6.1.4.1.4756.20.60.20.1.21 |
| f100IFxFEFLocal Local FRM220-10/100I card fiber detected Far End Fault:
0:Off
1:Detected | column | Enumeration | .1.3.6.1.4.1.4756.20.60.20.1.22 |
| f100IFxLBTestLocal Force remote FRM220-10/100I card to do fiber LoopBack testing:
0:Off
1:Action | column | Enumeration | .1.3.6.1.4.1.4756.20.60.20.1.23 |
| f100IFxLBStatusLocal Local FRM220-10/100I card fiber LoopBack testing status:
0:Off
1:Ok
2:Fail | column | Enumeration | .1.3.6.1.4.1.4756.20.60.20.1.24 |
| f100IFxRemoPWRAbLocal Local FRM220-10/100I card fiber Remote Power status:
0:Abnormal
1:OK | column | Enumeration | .1.3.6.1.4.1.4756.20.60.20.1.25 |
| f100IIrlMultLocal Local FRM220-10/100I card Ingress Rate Limit multiple:
When the irlMode-L is n x 32K mode, the irlMult-L
should be the value between 0 to 255;
When the irlMode-L is n x 512K mode,… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.4756.20.60.20.1.27 |
| f100IErlModeLocal Local FRM220-10/100I card Egress Rate Limit mode:
0:No limit
1:n x 32K
2:n x 512K | column | Enumeration | .1.3.6.1.4.1.4756.20.60.20.1.28 |
| f100IErlMultLocal Local FRM220-10/100I card Egress Rate Limit multiple:
When the erlMode-L is n x 32K mode, the erlMult-L
should be the value between 0 to 255;
When the erlMode-L is n x 512K mode, … | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.4756.20.60.20.1.29 |
| f100ICardHWVerLocal Local FRM220-10/100I card hardware version x.xxx | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.4756.20.60.20.1.3 |
| f100IFxRxByteLocal Local FRM220-10/100I card FX-in octet counter | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.4756.20.60.20.1.30 |
| f100IFxTxByteLocal Local FRM220-10/100I card FX-out octet counter | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.4756.20.60.20.1.31 |
| f100IFxFnlRxByteLocal Local FRM220-10/100I card FX-in final octets | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.4756.20.60.20.1.32 |
| f100IFxFnlTxByteLocal Local FRM220-10/100I card FX-out final octets | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.4756.20.60.20.1.33 |
| f100IPortResetLocal Force local FRM220-10/100I card to reset mode:
0:Off
1:Action | column | Enumeration | .1.3.6.1.4.1.4756.20.60.20.1.34 |
| f100IClrCountersLocal Force local FRM220-10/100I card to clear all counters:
0:Off
1:Action | column | Enumeration | .1.3.6.1.4.1.4756.20.60.20.1.35 |
| f100IOpModeLocal Local FRM220-10/100I card operation mode:
0:Switch mode
1:Converter mode | column | Enumeration | .1.3.6.1.4.1.4756.20.60.20.1.36 |
| f100ILfpModeLocal Local FRM220-10/100I card Link Fault Pass-through mode:
0:Disable
1:Enable | column | Enumeration | .1.3.6.1.4.1.4756.20.60.20.1.37 |
| f100IAlsModeLocal Local FRM220-10/100I card Auto Laser Shutdown mode:
0:Disable
1:Enable | column | Enumeration | .1.3.6.1.4.1.4756.20.60.20.1.38 |
| f100ISendFHRLocal Local FRM220-10/100I card send Fiber Hardware Reset
to remote:
0:No action
1:Action | column | Enumeration | .1.3.6.1.4.1.4756.20.60.20.1.39 |
| f100ICardFWVerLocal Local FRM220-10/100I card firmware version x.xxx | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.4756.20.60.20.1.4 |
| f100ISettoDefaultLocal Local FRM220-10/100I card Set to default:
0:No action
1:Action | column | Enumeration | .1.3.6.1.4.1.4756.20.60.20.1.40 |
| f100IFxDDLocal Local FRM220-10/100I card fiber Digital Diagnostic
function:
0:No
1:Yes | column | Enumeration | .1.3.6.1.4.1.4756.20.60.20.1.41 |
| f100IDDVendorLocal Local FRM220-10/100I card fiber D/D information:
Vendor name | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.4756.20.60.20.1.42 |
| f100IDDPartNoLocal Local FRM220-10/100I card fiber D/D information:
Vendor part number | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.4756.20.60.20.1.43 |
| f100IDDFiberTypeLocal Local FRM220-10/100I card fiber D/D information:
Fiber Type | column | Enumeration | .1.3.6.1.4.1.4756.20.60.20.1.44 |
| f100IDDWaveLenLocal Local FRM220-10/100I card fiber D/D information:
Wave length | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.4756.20.60.20.1.45 |
| f100IDDWaveLen2Local Local FRM220-10/100I card fiber D/D information:
Wave length 2 | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.4756.20.60.20.1.46 |
| f100IDDLinkLenLocal Local FRM220-10/100I card fiber D/D information:
Link length | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.4756.20.60.20.1.47 |
| f100IDDLenUnitLocal Local FRM220-10/100I card fiber D/D information:
Length Unit | column | Enumeration | .1.3.6.1.4.1.4756.20.60.20.1.48 |
| f100IDDStatusLocal Local FRM220-10/100I card fiber D/D information:
Status Support | column | Enumeration | .1.3.6.1.4.1.4756.20.60.20.1.49 |
| f100ICardCPLDVerLocal Local FRM220-10/100I card CPLD version x.xxx | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.4756.20.60.20.1.5 |
| f100IDDRxSensLocal Local FRM220-10/100I card fiber D/D information:
Rx Sensitivity | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.4756.20.60.20.1.50 |
| f100IDDTxPWRLocal Local FRM220-10/100I card fiber D/D information:
Tx power | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.4756.20.60.20.1.51 |
| f100IDDRxPWRLocal Local FRM220-10/100I card fiber D/D information:
Rx power | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.4756.20.60.20.1.52 |
| f100IDDTempLocal Local FRM220-10/100I card fiber D/D information:
Temperature in degree C | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.4756.20.60.20.1.53 |
| f100IDDPWRMarginLocal Local FRM220-10/100I card fiber D/D information:
Power margin | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.4756.20.60.20.1.54 |
| f100IDDPWRLossLocal Local FRM220-10/100I card fiber D/D information:
Power loss | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.4756.20.60.20.1.55 |
| f100IInfoR1SN1Local Local FRM220-10/100I card INFORemoteOM S/N 1 information | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.4756.20.60.20.1.56 |
| f100IInfoR1SN2Local Local FRM220-10/100I card INFORemoteOM S/N 2 information | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.4756.20.60.20.1.57 |
| f100ICardFPGAVerLocal Local FRM220-10/100I card FPGA version x.xxx | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.4756.20.60.20.1.6 |
| f100IPortActiveLocal Local FRM220-10/100I card active:
0:Inactive
1:Active | column | Enumeration | .1.3.6.1.4.1.4756.20.60.20.1.7 |
| f100IInBandManagLocal Local FRM220-10/100I card manages remote:
0:Disable
1:Enable | column | Enumeration | .1.3.6.1.4.1.4756.20.60.20.1.8 |
| f100IUtpLinkLocal Local FRM220-10/100I card UTP link status:
0:Down
1:Up | column | Enumeration | .1.3.6.1.4.1.4756.20.60.20.1.9 |