f100IErlMultRemote

CTC-FRM220-MIB · .1.3.6.1.4.1.4756.20.61.20.1.29
MIB view Table view

Object

column r/w SNMPv2-SMIInteger32 
Remote FRM220-10/100I card Egress Rate Limit multiple:
When the erlModeRemote is n x 32K mode, the erlMultRemote
should be the value between 0 to 255;
When the erlModeRemote is n x 512K mode, the erlMultRemote 
should be the value between 0 to 200.

Context

MIB
CTC-FRM220-MIB
OID
.1.3.6.1.4.1.4756.20.61.20.1.29
Type
column
Access
readwrite
Status
current
Parent
f100IRemoteEntry
Table
f100IRemoteTable
Siblings
56

Syntax

SNMPv2-SMIInteger32
Source
SNMPv2-SMIInteger32
Base type
Integer32

Values & Constraints

Type Constraints
range: -2147483648..2147483647

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
f100IChassisIndexRemote
A unique value for each local card. It is the chassis location number.
columnInteger32.1.3.6.1.4.1.4756.20.61.20.1.1
f100IUtpRxActRemote
Remote FRM220-10/100I card UTP receive active status: 0:Off 1:On
columnEnumeration.1.3.6.1.4.1.4756.20.61.20.1.10
f100IUtpNegoRemote
Remote FRM220-10/100I card UTP negotiation status: 0:Manual 1:Auto
columnEnumeration.1.3.6.1.4.1.4756.20.61.20.1.11
f100IUtpSpeedRemote
Remote FRM220-10/100I card UTP speed: 0:10MHz 1:100MHz
columnEnumeration.1.3.6.1.4.1.4756.20.61.20.1.12
f100IUtpDuplexRemote
Remote FRM220-10/100I card UTP duplex: 0:Half duplex mode 1:Full duplex mode
columnEnumeration.1.3.6.1.4.1.4756.20.61.20.1.13
f100IUtpSpeedStatusRemote
Remote FRM220-10/100I card UTP speed status: 0:10MHz 1:100MHz
columnEnumeration.1.3.6.1.4.1.4756.20.61.20.1.14
f100IUtpDuplexStatusRemote
Remote FRM220-10/100I card UTP duplex status: 0:Half duplex mode 1:Full duplex mode
columnEnumeration.1.3.6.1.4.1.4756.20.61.20.1.15
f100IUtpRxByteRemote
Remote FRM220-10/100I card UTP-in octet counter
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.4756.20.61.20.1.16
f100IUtpTxByteRemote
Remote FRM220-10/100I card UTP-out octet counter
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.4756.20.61.20.1.17
f100IUtpFnlRxByteRemote
Remote FRM220-10/100I card UTP-in final octets
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.4756.20.61.20.1.18
f100IUtpFnlTxByteRemote
Remote FRM220-10/100I card UTP-out final octets
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.4756.20.61.20.1.19
f100ISlotIndexRemote
A unique value for each remote card. It is the slot location number.
columnInteger32.1.3.6.1.4.1.4756.20.61.20.1.2
f100IFxLinkRemote
Remote FRM220-10/100I card fiber link status: 0:Down 1:Up
columnEnumeration.1.3.6.1.4.1.4756.20.61.20.1.20
f100IFxRxActRemote
Remote FRM220-10/100I card fiber receiver active status: 0:Off 1:On
columnEnumeration.1.3.6.1.4.1.4756.20.61.20.1.21
f100IFxFEFRemote
Remote FRM220-10/100I card fiber detected Far End Fault: 0:Off 1:Detected
columnEnumeration.1.3.6.1.4.1.4756.20.61.20.1.22
f100IFxLBTestRemote
Force local FRM220-10/100I card to do fiber LoopBack testing: 0:Off 1:Action
columnEnumeration.1.3.6.1.4.1.4756.20.61.20.1.23
f100IFxLBStatusRemote
Remote FRM220-10/100I card fiber LoopBack testing status: 0:Off 1:Ok 2:Fail
columnEnumeration.1.3.6.1.4.1.4756.20.61.20.1.24
f100IFxRemoPWRAbRemote
Remote FRM220-10/100I card fiber Remote Power status: 0:Abnormal 1:OK
columnEnumeration.1.3.6.1.4.1.4756.20.61.20.1.25
f100IIrlModeRemote
Remote FRM220-10/100I card Ingress Rate Limit mode: 0:No limit 1:n x 32K 2:n x 512K
columnEnumeration.1.3.6.1.4.1.4756.20.61.20.1.26
f100IIrlMultRemote
Remote FRM220-10/100I card Ingress Rate Limit multiple: When the irlModeRemote is n x 32K mode, the irlMultRemote should be the value between 0 to 255; When the irlModeRemote is n…
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.4756.20.61.20.1.27
f100IErlModeRemote
Remote FRM220-10/100I card Egress Rate Limit mode: 0:No limit 1:n x 32K 2:n x 512K
columnEnumeration.1.3.6.1.4.1.4756.20.61.20.1.28
f100ICardHWVerRemote
Remote FRM220-10/100I card hardware version x.xxx
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.4756.20.61.20.1.3
f100IFxRxByteRemote
Remote FRM220-10/100I card FX-in octet counter
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.4756.20.61.20.1.30
f100IFxTxByteRemote
Remote FRM220-10/100I card FX-out octet counter
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.4756.20.61.20.1.31
f100IFxFnlRxByteRemote
Remote FRM220-10/100I card FX-in final octets
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.4756.20.61.20.1.32
f100IFxFnlTxByteRemote
Remote FRM220-10/100I card FX-out final octets
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.4756.20.61.20.1.33
f100IPortResetRemote
Force remote FRM220-10/100I card to reset mode: 0:Off 1:Action
columnEnumeration.1.3.6.1.4.1.4756.20.61.20.1.34
f100IClrCountersRemote
Force remote FRM220-10/100I card to clear all counters: 0:Off 1:Action
columnEnumeration.1.3.6.1.4.1.4756.20.61.20.1.35
f100IOpModeRemote
Remote FRM220-10/100I card operation mode: 0:Switch mode 1:Converter mode
columnEnumeration.1.3.6.1.4.1.4756.20.61.20.1.36
f100ILfpModeRemote
Remote FRM220-10/100I card Link Fault Pass-through mode: 0:Disable 1:Enable
columnEnumeration.1.3.6.1.4.1.4756.20.61.20.1.37
f100IAlsModeRemote
Remote FRM220-10/100I card Auto Laser Shutdown mode: 0:Disable 1:Enable
columnEnumeration.1.3.6.1.4.1.4756.20.61.20.1.38
f100IFhrModeRemote
Remote FRM220-10/100I card accepts Fiber Hardware Reset mode: 0:Disable 1:Enable
columnEnumeration.1.3.6.1.4.1.4756.20.61.20.1.39
f100ICardFWVerRemote
Remote FRM220-10/100I card firmware version x.xxx
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.4756.20.61.20.1.4
f100ISettoDefaultRemote
Remote FRM220-10/100I card Set to default: 0:Disable 1:Enable
columnEnumeration.1.3.6.1.4.1.4756.20.61.20.1.40
f100IFxDDRemote
Remote FRM220-10/100I card fiber Digital Diagnostic function: 0:No 1:Yes
columnEnumeration.1.3.6.1.4.1.4756.20.61.20.1.41
f100IDDVendorRemote
Remote FRM220-10/100I card fiber D/D information: Vendor name
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.4756.20.61.20.1.42
f100IDDPartNoRemote
Remote FRM220-10/100I card fiber D/D information: Vendor part number
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.4756.20.61.20.1.43
f100IDDFiberTypeRemote
Remote FRM220-10/100I card fiber D/D information: Fiber Type
columnEnumeration.1.3.6.1.4.1.4756.20.61.20.1.44
f100IDDWaveLenRemote
Remote FRM220-10/100I card fiber D/D information: Wave length
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.4756.20.61.20.1.45
f100IDDWaveLen2Remote
Remote FRM220-10/100I card fiber D/D information: Wave length 2
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.4756.20.61.20.1.46
f100IDDLinkLenRemote
Remote FRM220-10/100I card fiber D/D information: Link length
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.4756.20.61.20.1.47
f100IDDLenUnitRemote
Remote FRM220-10/100I card fiber D/D information: Length Unit
columnEnumeration.1.3.6.1.4.1.4756.20.61.20.1.48
f100IDDStatusRemote
Remote FRM220-10/100I card fiber D/D information: Status Support
columnEnumeration.1.3.6.1.4.1.4756.20.61.20.1.49
f100ICardCPLDVerRemote
Remote FRM220-10/100I card CPLD version x.xxx
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.4756.20.61.20.1.5
f100IDDRxSensRemote
Remote FRM220-10/100I card fiber D/D information: Rx Sensitivity
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.4756.20.61.20.1.50
f100IDDTxPWRRemote
Remote FRM220-10/100I card fiber D/D information: Tx power
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.4756.20.61.20.1.51
f100IDDRxPWRRemote
Remote FRM220-10/100I card fiber D/D information: Rx power
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.4756.20.61.20.1.52
f100IDDTempRemote
Remote FRM220-10/100I card fiber D/D information: Temperature in degree C
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.4756.20.61.20.1.53
f100IDDPWRMarginRemote
Remote FRM220-10/100I card fiber D/D information: Power margin
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.4756.20.61.20.1.54
f100IDDPWRLossRemote
Remote FRM220-10/100I card fiber D/D information: Power loss
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.4756.20.61.20.1.55
f100IInfoR1SN1Remote
Remote FRM220-10/100I card INFORemoteOM S/N 1 information
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.4756.20.61.20.1.56
f100IInfoR1SN2Remote
Remote FRM220-10/100I card INFORemoteOM S/N 2 information
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.4756.20.61.20.1.57
f100ICardFPGAVerRemote
Remote FRM220-10/100I card FPGA version x.xxx
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.4756.20.61.20.1.6
f100IPortActiveRemote
Remote FRM220-10/100I card active: (It is read-only in remote side.) 0:Inactive 1:Active
columnEnumeration.1.3.6.1.4.1.4756.20.61.20.1.7
f100IInBandManagRemote
(Local only) FRM220-10/100I card manages remote: 0:Disable 1:Enable
columnEnumeration.1.3.6.1.4.1.4756.20.61.20.1.8
f100IUtpLinkRemote
Remote FRM220-10/100I card UTP link status: 0:Down 1:Up
columnEnumeration.1.3.6.1.4.1.4756.20.61.20.1.9