eth1gClientShutdownHoldoffTimer
CORIANT-GROOVE-MIB ·
.1.3.6.1.4.1.42229.1.2.4.1.66.1.1.11
Object
column
Unsigned32
The hold off time of client shutdown or replacement siganl at egress direction.
UNITS:milliseconds
default value :0
Context
- MIB
- CORIANT-GROOVE-MIB
- OID
.1.3.6.1.4.1.42229.1.2.4.1.66.1.1.11- Type
- column
- Access
- readonly
- Status
- current
- Parent
- eth1gEntry
- Table
- eth1gTable
- Siblings
- 26
Syntax
Unsigned32
Values & Constraints
Object Constraints
range: 0-2000
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| eth1gEthFecType The FEC working type of etyn port.
default value :auto | column | CoriantTypesEthFec | .1.3.6.1.4.1.42229.1.2.4.1.66.1.1.1 |
| eth1gClientShutdown The switching of client-shutdown.
default value :no | column | CoriantTypesYesNo | .1.3.6.1.4.1.42229.1.2.4.1.66.1.1.10 |
| eth1gHoldoffSignal Specify if specific signal will be sent out during hold off time
which avoid downstream equipment consequent action in the duration.
default value… | column | CoriantTypesYesNo | .1.3.6.1.4.1.42229.1.2.4.1.66.1.1.12 |
| eth1gNearEndAls The switching of near end ALS.
default value :no | column | CoriantTypesYesNo | .1.3.6.1.4.1.42229.1.2.4.1.66.1.1.13 |
| eth1gAlsDegradeMode The switching of defect BERSD-ODU trig ALS
default value :disabled | column | CoriantTypesEnableSwitch | .1.3.6.1.4.1.42229.1.2.4.1.66.1.1.14 |
| eth1gLoopbackEnable The enable switching of loopback function.
default value :disabled | column | CoriantTypesEnableSwitch | .1.3.6.1.4.1.42229.1.2.4.1.66.1.1.15 |
| eth1gLoopbackType The type mode of loopback function
default value :none | column | Enumeration | .1.3.6.1.4.1.42229.1.2.4.1.66.1.1.16 |
| eth1gTestSignalType The type mode of test signal.
default value :NONE | column | CoriantTypesTestSignalType | .1.3.6.1.4.1.42229.1.2.4.1.66.1.1.17 |
| eth1gTestSignalEnable The enable switching of test signal function
default value :NONE | column | CoriantTypesTestSignalConfig | .1.3.6.1.4.1.42229.1.2.4.1.66.1.1.18 |
| eth1gServiceLabel Path/service name of cross-connection related facility.
default value : | column | OctetString | .1.3.6.1.4.1.42229.1.2.4.1.66.1.1.19 |
| eth1gEthFecTypeState The FEC working state of etyn port.
default value :disabled | column | CoriantTypesEthFec | .1.3.6.1.4.1.42229.1.2.4.1.66.1.1.2 |
| eth1gManagedBy Describes whether this CRS was system created or not.
A system created CRS implies a HW cross connection, that is not
manageable by the user.
de… | column | Enumeration | .1.3.6.1.4.1.42229.1.2.4.1.66.1.1.20 |
| eth1gLldpStatusIf Port level lldp control.
Value of 'rxonly', then the LLDP agent will receive lldp,
when lldp-status-ne is also enabled.
Value of 'disabled', t… | column | Enumeration | .1.3.6.1.4.1.42229.1.2.4.1.66.1.1.21 |
| eth1gSpeed Set speed of the interface, unit mbps.
This is for ETH facility.
default value :1000 | column | Unsigned32 | .1.3.6.1.4.1.42229.1.2.4.1.66.1.1.22 |
| eth1gDuplex Set duplex selections.
default value :full | column | Enumeration | .1.3.6.1.4.1.42229.1.2.4.1.66.1.1.23 |
| eth1gMtu Set Maximum Frame Size.
default value :1500 | column | Unsigned32 | .1.3.6.1.4.1.42229.1.2.4.1.66.1.1.24 |
| eth1gAutoNegotiation Set Auto Negotiation: Enabled/Disabled.
default value :enabled | column | Enumeration | .1.3.6.1.4.1.42229.1.2.4.1.66.1.1.25 |
| eth1gCurrSpeed speed (UNKNOWN/AUTO/10/100/1000/10000) corresponding to the interface | column | OctetString | .1.3.6.1.4.1.42229.1.2.4.1.66.1.1.26 |
| eth1gCurrDuplex duplex (HALF/FULL) corresponding to the interface | column | OctetString | .1.3.6.1.4.1.42229.1.2.4.1.66.1.1.27 |
| eth1gTransmitInterpacketgap Specifies the minimum transmit IPG value.
default value :8 | column | Unsigned32 | .1.3.6.1.4.1.42229.1.2.4.1.66.1.1.3 |
| eth1gGfpPayloadFcs Enabled: GFP payload FCS will be used, Ethernet frame FCS will be removed;
Disabled: GFP payload FCS will not be inserted, Ethernet frame FCS will be used.
… | column | CoriantTypesEnableSwitch | .1.3.6.1.4.1.42229.1.2.4.1.66.1.1.4 |
| eth1gMappingMode The mapping mode of client port packets into ODUk.
default value :not-applicable | column | Enumeration | .1.3.6.1.4.1.42229.1.2.4.1.66.1.1.5 |
| eth1gAdminStatus The administrative state specifies the permission to use or prohibition
against using the resource. The administrative state can be modified by the user, and operates independent… | column | Enumeration | .1.3.6.1.4.1.42229.1.2.4.1.66.1.1.6 |
| eth1gOperStatus The operational state specifies whether or not a resource is able to provide service.
The operational state shall be visible to the operator. The user cannot modify the operation… | column | Enumeration | .1.3.6.1.4.1.42229.1.2.4.1.66.1.1.7 |
| eth1gAvailStatus Provided to qualify the operational, usage and/or administrative status attributes.
The value shall be a bits, management interface shall show the string with space separator ' '… | column | Bits | .1.3.6.1.4.1.42229.1.2.4.1.66.1.1.8 |
| eth1gAliasName User defined alias for this entity. Must be an alphanumeric string with dash or underscore | column | OctetString | .1.3.6.1.4.1.42229.1.2.4.1.66.1.1.9 |