smCfgCtrlOnResetEnableDisable
CME-MIB ·
.1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.9
Object
column
mandatory
r/w
Enumeration
Switch module configuration control on resets (default and unsolicited).
When set to enabled, the factory default IP configuration will become
active when the I/O module is reset to factory defaults by either the
management module or the I/O module. If an I/O module reset is initiated
by a source other than the management module then the previous IP configuration
will be in affect. In both these cases the MM will lose IP communications with
the IOM.
This MIB object can not be set, if MM grants switch module the Protected Mode
permission and switch module goes into Protected Mode.
NOTE: The numeric values for the enumerations for enabled and disabled are non-traditional
(i.e. - 0 and 1 are swapped), however, they cannot be changed since this MIB is already
published.
NOTE: This MIB object is not applicable to modules that are running in Network Address
Translation (NAT) Mode. A value of disabled(1) will be returned.
Context
- MIB
- CME-MIB
- OID
.1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.9- Type
- column
- Access
- readwrite
- Status
- mandatory
- Parent
- smControlEntry
- Table
- smControlTable
- Siblings
- 11
Syntax
Enumeration
Values & Constraints
Enumerated Values
0 | enabled |
1 | disabled |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| smControlIndex mandatory Switch module control table index. | column | Integer32 | .1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.1 |
| smHealthState mandatory The health state for the switch module.
0 = unknown, 1 = good, 2 = warning, 3 = bad. | column | Enumeration | .1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.15 |
| smPMState mandatory The Protected Mode Status for the switch module.
standby- Protected Mode capability exists on the IOM but has not
been activated on the switch module or the MM.
pending - Protecte… | column | Enumeration | .1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.16 |
| smPMCtrlEnableDisable mandatory MM Protected Mode permission for the switch module.
disabled - allow MM to disable Protected Mode Permission for the switch module.
enabled - allow MM to grant Protected Mode Perm… | column | Enumeration | .1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.17 |
| smIOCompatibility mandatory The compatibility status for the I/O module.
The possible values and their meanings are as follows:
Unknown: This indicates a communication error for the I/O module… | column | OctetString | .1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.18 |
| switchModuleControlId mandatory The switch module numeric identifier. | column | Enumeration | .1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.2 |
| smPostResultsAvailable mandatory Describes whether the switch module POST diagnostic result
value contained in the smPostResultsValue is valid. | column | Enumeration | .1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.3 |
| smPostResultsValue mandatory The range of values and meanings are as follows:
0x00 - 0x7F ( 0 - 127) Base internal functions
0x80 - 0x9F (128 - 159) Internal interface failures
0xA0 - 0xAF (160 - 175) … | column | OctetString | .1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.4 |
| switchModuleMemDiagEnableDisable obsolete Switch module memory diagnostics enabled or disabled.
NOTE: The numeric values for the enumerations for enabled and disabled are non-traditional
(i.e. - 0 and… | column | Enumeration | .1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.5 |
| smCfgCtrlEnableDisable mandatory Switch module configuration control. When set to enabled, only the MM can manage
the module.
This MIB object can not be set, if MM grants switch module the Protected Mode permiss… | column | Enumeration | .1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.6 |
| smExtEthPortsEnableDisable mandatory Switch module non-management ethernet ports enabled or disabled.
This MIB object can not be set, if MM grants switch module the
Protected Mode permission.
This MIB object can not … | column | Enumeration | .1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.7 |