esaProbeProtocol
CM-SA-MIB ·
.1.3.6.1.4.1.2544.1.12.8.1.4.1.6
Object
column
r/w
EsaProbeProtocol
Protocol to be used in ESA Probe messages. 'icmpTimestamp', 'icmpEcho', 'udpEcho' protocols support layer-3 ethernet service assurance. If the remote reflector is an ADVA equipment based on CM family of products, one-way loss measurement, one-way delay measurement, round-trip delay measurement and one-way jitter measurements are computed. Else, only round-trip delay measurements are applicable. 'y1731' protocol can be used for layer-2 ethernet service assurance. One-way loss measurement, one-way and round-trip delay measurement, and one-way jitter measurements are available for this protocol. 'y1731-slm-slr' protocol can be used for layer-2 ethernet service assurance using Synthetic Loss Measurement messages. One-way loss measurement, one-way and round-trip delay measurement, and one-way jitter measurements are available for this protocol.
Context
- MIB
- CM-SA-MIB
- OID
.1.3.6.1.4.1.2544.1.12.8.1.4.1.6- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- esaProbeEntry
- Table
- esaProbeTable
- Siblings
- 52
Syntax
EsaProbeProtocol
- Source
- EsaProbeProtocol
- Base type
Enumeration
Values & Constraints
Type Values
1 | icmpEcho |
2 | udpEcho |
3 | icmpTimestamp |
4 | y1731 |
5 | y1731-slm-slr |
6 | y1731-slm-dmm |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| esaProbeIndex An integer index value used to uniquely identify
this ESA Probe within a Card. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2544.1.12.8.1.4.1.1 |
| esaProbeSrcMep This attribute is applicable only for Y.1731 probes. It identifies
the source MEP that initiates the Y.1731 LMMs and DMMs. | column | SNMPv2-TCVariablePointer | .1.3.6.1.4.1.2544.1.12.8.1.4.1.10 |
| esaProbeDestMepType This attribute is applicable only for Y.1731 probes. This indicates
if the destination MEP is specified using the MEP ID object
esaProbeDestMepId. | column | CM-COMMON-MIBMepDestinationType | .1.3.6.1.4.1.2544.1.12.8.1.4.1.11 |
| esaProbeDestMepMacAddr This attribute is applicable only for Y.1731 probes. It identifies
the destination MEP that responds to the LMMs and DMMs. This
MAC address will be the destination MAC address for… | column | SNMPv2-TCMacAddress | .1.3.6.1.4.1.2544.1.12.8.1.4.1.12 |
| esaProbeDestMepId This attribute is applicable only for Y.1731 probes. It identifies
the destination MEP that responds to the LMMs and DMMs. The MAC
address of this RMEP ID from RMEP database will … | column | IEEE8021-CFM-MIBDot1agCfmMepIdOrZero | .1.3.6.1.4.1.2544.1.12.8.1.4.1.13 |
| esaProbeVlanTagEnabled Ability to specify whether or not to use VLAN tagged or untagged
ESA traffic generation on the Probe.
NOTE: This attribute is not applicable to Y.1731 probes. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2544.1.12.8.1.4.1.14 |
| esaProbeVlanTagEtherType This variable allows the user to specify the
monitored service's VLAN tag Ether Type.
Valid if 'esaProbeVlanTagEnabled' is specified as TRUE.
NOTE: This attribute is not applica… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2544.1.12.8.1.4.1.15 |
| esaProbeVlanId This variable allows the user to specify the
monitored service's VLAN tag. Valid if 'esaProbeVlanTagEnabled'
is specified as TRUE.
NOTE: This attribute is not applicable to Y.17… | column | CM-COMMON-MIBVlanId | .1.3.6.1.4.1.2544.1.12.8.1.4.1.16 |
| esaProbeVlanPrio This variable allows the user to specify the
monitored service's VLAN priority. Valid if
'esaProbeVlanTagEnabled' is specified as TRUE.
NOTE: This attribute is not applicable to Y… | column | CM-COMMON-MIBVlanPriority | .1.3.6.1.4.1.2544.1.12.8.1.4.1.17 |
| esaProbeInnerVlanTagEnabled Ability to specify whether or not to use Inner VLAN tag.
NOTE: This attribute is not applicable to Y.1731 probes. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2544.1.12.8.1.4.1.18 |
| esaProbeInnerVlanTagEtherType This variable allows the user to specify the
monitored service's Inner VLAN tag Ether Type.
Valid if 'esaProbeInnerVlanTagEnabled' is specified as TRUE.
NOTE: This attribute is … | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2544.1.12.8.1.4.1.19 |
| esaProbeName A unique identifier used by the Manager to distinguish
the ESA Probe. | column | OctetString | .1.3.6.1.4.1.2544.1.12.8.1.4.1.2 |
| esaProbeInnerVlanId This variable allows the user to specify the
monitored service's Inner VLAN tag. Valid if 'esaProbeInnerVlanTagEnabled'
is specified as TRUE.
NOTE: This attribute is not applica… | column | CM-COMMON-MIBVlanId | .1.3.6.1.4.1.2544.1.12.8.1.4.1.20 |
| esaProbeInnerVlanPrio This variable allows the user to specify the
monitored service's Inner VLAN priority. Valid if
'esaProbeInnerVlanTagEnabled' is specified as TRUE.
NOTE: This attribute is not appl… | column | CM-COMMON-MIBVlanPriority | .1.3.6.1.4.1.2544.1.12.8.1.4.1.21 |
| esaProbeIpPrioMapMode This object enables specification of Priority Mapping Mode for
the ESA Probe.
NOTE: This attribute is not applicable to Y.1731 probes. | column | CM-COMMON-MIBIpPriorityMapMode | .1.3.6.1.4.1.2544.1.12.8.1.4.1.22 |
| esaProbeIpPriority This object enables specification of Priority Value for
esaProbePrioMapMode as priomap-tos,priomap-dscp.
NOTE: This attribute is not applicable to Y.1731 probes. | column | Integer32 | .1.3.6.1.4.1.2544.1.12.8.1.4.1.23 |
| esaProbePktsPerSample This object enables specification of number of packets within
a sample run for ESA traffic generation. A non-zero value
must be specified.
NOTE: This attribute is not applicable t… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2544.1.12.8.1.4.1.24 |
| esaProbePktSize This object enables specification of fixed length frame size
in bytes for ESA traffic generation. If not specified, default value
of 104 bytes is used.
NOTE: This attribute is no… | column | Integer32 | .1.3.6.1.4.1.2544.1.12.8.1.4.1.25 |
| esaProbeInterPktGap This object enables specification of interval in milliseconds between
packet generation. A non-zero value must be specified.
NOTE: This attribute is not applicable to Y.1731 probe… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2544.1.12.8.1.4.1.26 |
| esaProbePktDeadInterval This object enables specification of the dead interval in seconds
after 'esaProbePktsPerSample' have been generated within the sample.
This allows for settling time of the ESA tra… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2544.1.12.8.1.4.1.27 |
| esaProbeResponseTimeout This object allows specification of the timeout value to
determine lost packets. Time specified in seconds.
NOTE: This attribute is not applicable to Y.1731 probes.
… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2544.1.12.8.1.4.1.28 |
| esaProbeY1731DmmPktSize This object is only applicable to Y.1731 probes.
This object enables specification of the TLV size for
Delay Measurement Frames (DMMs).
Value of 0 is a read-only va… | column | Integer32 | .1.3.6.1.4.1.2544.1.12.8.1.4.1.29 |
| esaProbeSourcePort This object points to the Port to which the ESA Probe
is attached, i.e.on which the service to be monitored resides. | column | SNMPv2-TCVariablePointer | .1.3.6.1.4.1.2544.1.12.8.1.4.1.3 |
| esaProbeY1731LmmInterval LMM frame transmission period.
For Loss Measurement Frames, only interval-1sec is supported.
This attribute is only applicable to Y.1731 probes. | column | EsaProbePktIntervalType | .1.3.6.1.4.1.2544.1.12.8.1.4.1.30 |
| esaProbeY1731DmmInterval DMM frame transmission period.
This attribute is only applicable to Y.1731 probes. | column | EsaProbePktIntervalType | .1.3.6.1.4.1.2544.1.12.8.1.4.1.31 |
| esaProbeHistoryBins This object allows specification of number of history bins.
This is the total history data that will be maintained
for an ESA Probe run, at any instance. | column | Integer32 | .1.3.6.1.4.1.2544.1.12.8.1.4.1.32 |
| esaProbeHistoryInterval This object allows specification of the history interval
period. | column | EsaProbeHistoryIntervalType | .1.3.6.1.4.1.2544.1.12.8.1.4.1.33 |
| esaProbeDistHistoryBins This object allows specification of number of distribution
history bins. This is the total history distribution data that
will be maintained for an ESA Probe run, at any instance. | column | Integer32 | .1.3.6.1.4.1.2544.1.12.8.1.4.1.34 |
| esaProbeDistHistoryInterval This object allows specification of the history distribution
interval period. | column | EsaProbeHistoryIntervalType | .1.3.6.1.4.1.2544.1.12.8.1.4.1.35 |
| esaProbeCreationTime This object provides the creation time of the ESA Probe. | column | SNMPv2-TCDateAndTime | .1.3.6.1.4.1.2544.1.12.8.1.4.1.36 |
| esaProbeStorageType The type of storage configured for this entry. | column | SNMPv2-TCStorageType | .1.3.6.1.4.1.2544.1.12.8.1.4.1.37 |
| esaProbeRowStatus The status of this row.
An entry MUST NOT exist in the active state unless all
objects in the entry have an appropriate value, as described
in the description clause for each writ… | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.2544.1.12.8.1.4.1.38 |
| esaProbeMultiCOSEnabled This object is introduced for FSP150CC Release 4.3.
This object is only applicable for Y.1731 and
SLM-SLR Probe Protocol Types. This object can be used
to specify the multiple … | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2544.1.12.8.1.4.1.39 |
| esaProbeAssocSchedGroup This object points to the probe's associated Scheduled Group.
Initially, when the probe is not associated with a Group,
this object's value is set to {0.0}. | column | SNMPv2-TCVariablePointer | .1.3.6.1.4.1.2544.1.12.8.1.4.1.4 |
| esaProbeSLAMonitorType This object indicates whether the Probe is a point-to-point type
or a point-to-multipoint type. Only SLM-SLR probes can be
point-to-multipoint. | column | EsaProbeSLAMonitorType | .1.3.6.1.4.1.2544.1.12.8.1.4.1.40 |
| esaProbeCOSType This object can be used to specify the first Class of Service associated with
the Y.1731/SLM-SLR ESA Probe. In the case of a multiCOS Probe, this object
has no semantics when mul… | column | CM-COMMON-MIBClassOfServiceType | .1.3.6.1.4.1.2544.1.12.8.1.4.1.41 |
| esaProbeSLMMulticastMACEnabled This object can be used to specify whether the SLM/SLR protocol Probe will use
multicast MAC address in SLM (Synthetic Loss Measurement) messages.
This object is only valid for S… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2544.1.12.8.1.4.1.42 |
| esaProbeSOAMInterval This object can be used to specify the packet interval type for Y.1731 LM/DM
and SLM/SLR based ESA Probes, for the first Class of Service.
In the case of a multiCOS Probe, this … | column | EsaProbePktIntervalType | .1.3.6.1.4.1.2544.1.12.8.1.4.1.43 |
| esaProbeSOAMPktSize This object can be used to specify the packet size for SLM-SLR based ESA Probes,
for the first Class of Service. In the case of multiCOS Probe, this object has
no semantics when … | column | Integer32 | .1.3.6.1.4.1.2544.1.12.8.1.4.1.44 |
| esaProbeInner2VlanTagEnabled Ability to specify whether or not to use Inner2 VLAN tag.
NOTE: This attribute is not applicable to Y.1731 probes. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2544.1.12.8.1.4.1.45 |
| esaProbeInner2VlanTagEtherType This variable allows the user to specify the
monitored service's Inner2 VLAN tag Ether Type.
Valid if 'esaProbeInner2VlanTagEnabled' is specified as TRUE.
NOTE: This attribute i… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2544.1.12.8.1.4.1.46 |
| esaProbeInner2VlanId This variable allows the user to specify the
monitored service's Inner2 VLAN tag. Valid if 'esaProbeInner2VlanTagEnabled'
is specified as TRUE.
NOTE: This attribute is not appli… | column | CM-COMMON-MIBVlanId | .1.3.6.1.4.1.2544.1.12.8.1.4.1.47 |
| esaProbeInner2VlanPrio This variable allows the user to specify the
monitored service's Inner2 VLAN priority. Valid if
'esaProbeInner2VlanTagEnabled' is specified as TRUE.
NOTE: This attribute is not ap… | column | CM-COMMON-MIBVlanPriority | .1.3.6.1.4.1.2544.1.12.8.1.4.1.48 |
| esaProbeAdminState This object represents the Administrative State of the ESA Probe.
This is not externally managed. | column | CM-COMMON-MIBAdminState | .1.3.6.1.4.1.2544.1.12.8.1.4.1.49 |
| esaProbeDirection This object allows to specify the direction of Probe
traffic generation. | column | EsaProbeDirection | .1.3.6.1.4.1.2544.1.12.8.1.4.1.5 |
| esaProbeOperationalState This object represents the Operational State of the ESA Probe. | column | CM-COMMON-MIBOperationalState | .1.3.6.1.4.1.2544.1.12.8.1.4.1.50 |
| esaProbeSecondaryState This object represents the Secondary State of the ESA Probe. | column | CM-COMMON-MIBSecondaryState | .1.3.6.1.4.1.2544.1.12.8.1.4.1.51 |
| esaProbeMacAddress This attribute is applicable only for Y.1731 probes. It identifies
the destination MacAddress which esa using | column | SNMPv2-TCMacAddress | .1.3.6.1.4.1.2544.1.12.8.1.4.1.52 |
| esaProbeAlias This object allows SNMP management entities to provide an
alias for an ESA Probe. | column | OctetString | .1.3.6.1.4.1.2544.1.12.8.1.4.1.53 |
| esaProbeSrcIpAddress Variable that allows specification of the Probe's source
IP Address. This IP Address is used in the IP header of
the ESA Probe generated packets, as source address.
NOTE: This at… | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.2544.1.12.8.1.4.1.7 |
| esaProbeSrcSubnetMask Variable that allows specification of the Probe's source
IP Subnet Mask.
NOTE: This attribute is not applicable to Y.1731 probes. | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.2544.1.12.8.1.4.1.8 |
| esaProbeDestIpAddress Variable that allows specification of the Reflector's
destination IP Address. This IP Address is used in the IP header
of the ESA Probe generated packets, as destination address.… | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.2544.1.12.8.1.4.1.9 |