egressQSelect
CISCO-WAN-FR-CONN-MIB ·
.1.3.6.1.4.1.351.110.5.1.2.1.1.1.5
Object
column
r/w
Enumeration
Selects one out of two possible port queues. The default port queue number is 1 which is the high pririty queue. 1 = High priority queue 2 = Low priority queue 3 = Indicates that this entry is not used (eg: in FRSM-VHS, chanServType indicates the channel service type and would determine the queue to which the channel gets mapped) For FRSM12 Card: This object is used to select between the two ATM-COS queues in the egress direction.
Context
- MIB
- CISCO-WAN-FR-CONN-MIB
- OID
.1.3.6.1.4.1.351.110.5.1.2.1.1.1.5- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- frChanCnfGrpEntry
- Table
- frChanCnfGrpTable
- Siblings
- 72
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | highPriority |
2 | lowPriority |
3 | notSupported |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| chanNum The value of this object identifies the
frame relay connection/channel index.
Note that the actual range of the index
supported by a card depends on the type of car… | column | Integer32 | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.1 |
| egressQDEThresh This variable sets the max depth for queue, before
they become discard eligible. It is defined in terms of
number of bytes.
In all cards except the FRSM-VHS card, the range is
li… | column | Integer32 | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.10 |
| egressQECNThresh This variable sets the max depth for queue, before
it starts flow control. It is defined in terms of
number of bytes.
In all cards except the FRSM-VHS card, the range is
limited… | column | Integer32 | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.11 |
| deTaggingEnable This object enables/disables the DE tagging.
The tagging is enabled only in the ingress
direction.
For FRSM12 Card:
When this object is disabled, the ingress poli… | column | Enumeration | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.12 |
| cir The value of this object is equal to the CIR parameter
for this frame relay connection.
The CIR value have to be less than or equal to the port speed.
Any value fro… | column | bps Integer32 | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.13 |
| bc The value of this object is equal to the
committed burst size(BC) parameter for this
PVC endpoint.
The value of bc can not be 0 when cir is non zero.
The value of b… | column | bytes Integer32 | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.14 |
| be The value of this object is euqal to the
excess burst size(Be) parameter for this PVC
endpoint.
The value be can not be 0 when cir is 0.
The peak v… | column | bytes Integer32 | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.15 |
| ibs The value of this object is euqal to the
excess burst size(Be) parameter for this PVC
endpoint.
The value of ibs should be less or equal to bc
when cir is greate… | column | Integer32 | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.16 |
| foreSightEnable This variable enables/disables foreSight option.
Following objects can be modified only when this
object is set to enable(1):
qir, mir, pir
… | column | Enumeration | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.17 |
| qir The value of this object is euqal to the
quiescent information rate for Foresight.
The unit is 1 Cell/Sec = 16 fastpackets/sec.
Following informatio… | column | fastpackets-per-second Integer32 | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.18 |
| mir The value of this object is euqal to the
minimum information rate for Foresight.
The unit is 1 Cell/Sec = 16 fastpackets/sec.
is equal to 16 fastpackets/sec.
… | column | fastpackets-per-second Integer32 | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.19 |
| chanRowStatus This object is used for adding/modifying/deleting
the channel.
add(1) : For adding the frame relay connections.
delete(2): For deleting frame relay connections.
mod(3) : For M… | column | Enumeration | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.2 |
| pir The value of this object is euqal to the
peak information rate for Foresight.
The unit is 1 Cell/Sec = 16 fastpackets/sec.
is equal to 16 fastpackets/sec.
… | column | fastpackets-per-second Integer32 | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.20 |
| chanLocRmtLpbkState This variable enables or disables the remote loopback for each
channel.
When you enable this option on a connection (channel) then all the
cells that are coming from the network s… | column | Enumeration | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.21 |
| chanTestType The chanTestType starts testing the continuity
or delay of a connection.
It sends specific cell patterns toward the network
and the terminating end of this connection has to be … | column | Enumeration | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.22 |
| chanTestState This shows the state of the test
When you add a connection then the chanTestState becomes notinprogress
and when you select any test, it would go to inprogress state and after
it … | column | Enumeration | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.23 |
| chanRTDResult This is round trip delay in milliseconds.
When you select testdelay option for the chanTestType, the result of
the test that is measured in milliseconds can be read in chanRTDResu… | column | Integer32 | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.24 |
| chanType The value of this object is used for setting the
channel type of a frame relay connection. If set
with values frSIW-transparent(2) and frSIW-translate(3),
all PVC data is subject … | column | Enumeration | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.25 |
| chanFECNconfig The value of this object specifies how to map
from FECN field in the frame Relay PDU to
the EFCI field in the ATM cells.
This object does not apply to NIW.
This is… | column | Enumeration | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.26 |
| chanDEtoCLPmap The value of this object specifies how to map
from DE bit on the Frame Relay side to CLP
bit on the ATM side.
mapCLP(1) : Map DE bit to CLP bit in ATM cell.
set… | column | Enumeration | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.27 |
| chanCLPtoDEmap The value of this object enables mapping of
Cell Loss Priority(CLP) bit on the ATM Side
to Discard Eligibility(DE) bit on the Frame relay
side.
The possible values… | column | Enumeration | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.28 |
| chanIngrPercentUtil The ingress utilization on a
frame relay connection. | column | percentage Integer32 | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.29 |
| chanPortNum This object refers to the frame relay
port on which channel is created.
This is a mandatory object for creating the channel.
For FRSM12 Card:
This object contains t… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.3 |
| chanEgrPercentUtil The egress utilization on a
frame relay connection. | column | percentage Integer32 | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.30 |
| chanEgrSrvRate The value of this object identifies egress CIR
value for a frame relay connection.
The value of this object must be less than or equal(<=)
to the port speed.
… | column | Integer32 | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.31 |
| chanOvrSubOvrRide The value of this object enables/disables the
oversubscription on a connection.
This object allows one to add a new connection on a port
even if it is over subscribed.
… | column | Enumeration | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.32 |
| chanFrConnType The value of this object is used for configuring
connection type of a frame relay connection.
The possible values are :
pvc(1) : Permanent Virtua… | column | Enumeration | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.33 |
| frCDRNumber The value of this object identifies
the CDR(Call Detail Record) number.
This is the key to correlate
cell/frame counts, start/end record.
For FRSM12 Card: Not S… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.34 |
| frLocalVpi The value of this object provides the VPI
value for the local endpoint.
This object in conjunction with frLocalVci and
frLocalNSAP represents the local end point of
this connect… | column | Integer32 | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.35 |
| frLocalVci The value of this object provides the VCI
value for the local endpoint.
This object in conjunction with frLocalVpi and
frLocalNSAP represents the local end point of
this connec… | column | Integer32 | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.36 |
| frLocalNSAP The value of this object identifies the
NSAP address of the frame relay connection.
The value of this object follows the format:
Prefix : 13 Bytes
… | column | OctetString | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.37 |
| frRemoteVpi The value of this object identifies the VPI value of remote
end point of this connection. The frRemoteVpi, frRemoteVci
and frRemoteNSAP identifies the remote end point of
this con… | column | Integer32 | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.38 |
| frRemoteVci The value of this object identifies the VCI value of remote
end point of this connection. The frRemoteVpi, frRemoteVci
and frRemoteNSAP identifies the remote end point of
this con… | column | Integer32 | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.39 |
| dLCI The value of this object is the DLCI number of the channel.
This is a mandatory object for creating the channel.
All the connections on the same por… | column | Integer32 | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.4 |
| frRemoteNSAP The value of this object identifies the
NSAP address of the frame relay connection.
The value of this object follows the format:
Prefix : … | column | OctetString | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.40 |
| frMastership This is used by PXM to determine if this end point is
master or slave, a new type unknown is added to identify
the SM in MGX8220 shelf and the SM in MGX shelf. In AXIS
shelf, use… | column | Enumeration | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.41 |
| frVpcFlag This represents the connection type, used for PXM to
identify VPC/VCC but FRSM card doesn't use it
always set to vcc for FRSM card
For FRSM12 Card:
For chanFrConnType = pnni(5), t… | column | Enumeration | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.42 |
| frConnServiceType This specifies the service type
1 ==> Constant Bit Rate
2 ==> Variable Bit Rate
3 ==> Not used
4 ==> Unspecified Bit Rate
5 ==> ATM frame relay
6 ==> standard ABR
7 ==> foresight… | column | Enumeration | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.43 |
| frRoutingPriority This is used by PXM to determine how important this
connection is when selecting connections to route | column | Integer32 | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.44 |
| frMaxCost The value of this object specifies the
Maximum allowed cost. It is related to Cost Based Routing.
This is used by PXM so that it won't choose a path with
a cost greater than this … | column | Integer32 | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.45 |
| frRestrictTrunkType Restricted trunk type for routing, used by PXM. It
specifies that the connection either cannot be routed over
satelite trunks, or terrestrial trunks, or it can be on
any type of … | column | Enumeration | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.46 |
| frConnPCR The value of this object identifies
the PCR(Peak Cell Rate). If not provided in
the connection setup request, it'll be derived from
object 'pir'.
For FRSM12 Card:… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.47 |
| frConnRemotePCR Peak cell rate of the other end, if not set, will be
set to the same as local end PCR (frConnPCR). However,
note that if the CIRs for both local and remote end
are set to the diff… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.48 |
| frConnMCR Minimum cell rate, if not provided in the connection setup
request, it'll be derived from object 'mir'.
For FRSM12 Card:
Default value is frConnPCR | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.49 |
| frConnRemoteMCR Minimum cell rate of the other end, if not set, will be
set to the same as local end MCR (frConnMCR). However,
note that if the CIRs for both local and remote end
are set to the d… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.50 |
| frConnPercentUtil This is the expected long-term utilization of the
channel by this end-point. If this is not specified in
the connection setup request, it'll be defaulted to
100 percent
… | column | Integer32 | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.51 |
| frConnRemotePercentUtil This is the expected long-term utilization of the
channel by the other end-point. If this is not specified in
the connection setup request, it'll be set to be the same
as the loca… | column | Integer32 | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.52 |
| frConnForeSightEnable This object is used by the controller(PAR/PNNI/TAG) to
set up the Qbin for the connection, if this is not set,
it'll be defaulted by SM to the same as foreSightEnable
in the end p… | column | Enumeration | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.53 |
| frConnFGCRAEnable The value of this object is used for
enabling/disabling Frame based GCRA
(early packet discard).
For FRSM12 Card: Not Supported. | column | Enumeration | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.54 |
| chanServType The value of this object indicates the
indicates the class of the connection.
1-High priority (typically CBR connections)
2- real-time VBR
3- non-real time VBR
4- Ava… | column | Enumeration | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.55 |
| chanServiceRateOverride This variable sets the SAR IR programming option.
Foresight and chanServiceRateOverride are mutually exclusive.
For FRSM12 Card: Not Supported. | column | Enumeration | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.56 |
| chanServiceRate This is the rate to which IR can be set to when
chanServiceRateOverride is set to enable(1). If
chanServiceRateOverride is disable(2) then this object
does not have any signific… | column | Integer32 | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.57 |
| zeroCirConEir The value of this object defines defines EIR
value for '0' CIR connection.
If the value is '0', EIR is set to port speed.
If zeroCirConEir is non-zero value, EIR i… | column | Integer32 | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.58 |
| chanReroute This is used by the administrator to trigger the re-routing
of the connection. The rerouting takes effect, when this object
is set to true(1). When set to false (2), no action is … | column | Enumeration | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.59 |
| ingressQDepth This variable sets the max depth for queue, before
it starts dropping the cells. It is defined in
terms of number of bytes.
In all cards except the FRSM-VHS card, the range is
lim… | column | Integer32 | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.6 |
| frConnSCR Sustained cell rate, Used for VBR connections setup with PNNI
controller.
For FRSM12 Card: Default value is frConnPCR
This object is not applicable to MGX Release 1.x. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.60 |
| frConnRemoteSCR Sustained cell rate of the other end, Used for VBR connections
setup with PNNI controller.
For FRSM12 Card: Default value is frConnSCR
This object is not applicable to MGX Releas… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.61 |
| frConnTemplateId This object specifies the template identifier for the connection
template associated with this connection.
The valid range for templates is 1..16.
A value of 17 indicates no templ… | column | Integer32 | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.62 |
| frConnAdminStatus This object specifies channel admin status.
This object is not applicable to MGX Release 1.x. | column | Enumeration | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.63 |
| frChanCnfChangeCount This object is added only for FRSM12 card.
This counter tracks the number of configuration changes
that happen on a channel. The counter is
associated only with … | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.64 |
| frChanCnfIgnoreIncomingDE This object is added for FRSM12 card.
When this object is enabled, the incoming frames with
DE(Discard Eligible) bit set to 1 are counted in the
Bc bucket instead of Be bucket
… | column | Enumeration | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.65 |
| frChanOamCCEnable This object is added for FRSM12 card.
This object serves to enable or disable continuity check(CC)
on a connection endpoint. When continuity check is enabled
on an… | column | Enumeration | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.66 |
| frChanStatsEnable This object serves the purpose of enabling/disabling statistics
collection on a per connection basis. In implementations which
do not have such limitations, this object can be set… | column | Enumeration | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.67 |
| frChanLocalLpbkEnable This object is added for FRSM12 card.
This object when enabled adds a channel-level loopback
towards the port side. If the connection is in loopback,
Connection MIB (FrChanCnfGrp… | column | Enumeration | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.68 |
| frChanUpcEnable This object is added for FRSM12 card.
This object when disabled, disables Frame Relay policing.
This object is not applicable to MGX Release 1.x. | column | Enumeration | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.69 |
| ingressQECNThresh This variable sets the max depth for queue, before
it starts flow control. It is defined in terms of
number of bytes.
In all cards except the FRSM-VHS card, the range is
limited … | column | Integer32 | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.7 |
| frChanSlaveType This object is added for FRSM12 card.
This object indicates whether a master endpoint has a persistent
slave or not. A connection with a master and a non-persistent
slave is consi… | column | Enumeration | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.70 |
| frConnRemoteMBS Remote Maximum Burst Size in terms of number of cells.
This object should be set by the user in cases when
the remote end of the connection is an ATM end-point
where the Local MBS… | column | Integer32 | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.71 |
| frChanPrefRouteId This object serves to to associate a preferred
route with a connection.
The value '0' means no preferred route is associated with
this connection.
… | column | Integer32 | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.72 |
| frChanDirectRoute This object serves to associate a prefer
route as directed route (correspond to the prefer route
object frChanPrefRouteId).
A directed route specifies that the ass… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.73 |
| ingressQDEThresh This variable sets the max depth for queue, before
they become discard eligible. It is defined in terms of
number of bytes.
In all cards except the FRSM-VHS card, the range is
li… | column | Integer32 | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.8 |
| egressQDepth This variable sets the max depth for queue, before
it starts dropping the cells. It is defined in terms of
number of bytes.
In all cards except the FRSM-VHS card, the range is
l… | column | Integer32 | .1.3.6.1.4.1.351.110.5.1.2.1.1.1.9 |