cesRemoteNSAP
CISCO-WAN-CES-CONN-MIB ·
.1.3.6.1.4.1.351.110.5.3.2.1.1.1.32
Object
column
r/w
OctetString
This object identifies the NSAP address of the
peer endpoint.
The NSAP address is 20 bytes long and follows the format:
- 13 bytes as prefix 2 bytes for Cisco ID,
- 2 bytes for Cisco ID
- 1 byte reserved
- 3 bytes for logical interface
(slot:1 bytes,port number:2 bytes)
- 1 byte is for Selector(SEL).
Context
- MIB
- CISCO-WAN-CES-CONN-MIB
- OID
.1.3.6.1.4.1.351.110.5.3.2.1.1.1.32- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- cesmChanCnfGrpEntry
- Table
- cesmChanCnfGrpTable
- Siblings
- 49
Syntax
OctetString
Values & Constraints
Object Constraints
range: 0-20
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| cesCnfChanNum This object identifies the channel number of the
CESM channel.
For CESM-4P the range is 16..19 (only for 4 entries).
For CESM-8t1 the range is 16..192
For CESM-8e1 the range is 1… | column | Integer32 | .1.3.6.1.4.1.351.110.5.3.2.1.1.1.1 |
| cesBufMaxSize Specifies the maximum size in octets of egress buffer.
CESM - 4P:
Should be at least 0.6*CDVRxT for a T1 line and
0.7 * CDVRxT for a E1 line. 0 can be specified to internally
co… | column | Integer32 | .1.3.6.1.4.1.351.110.5.3.2.1.1.1.10 |
| cesCDVRxT This object specifies maximum cell arrival jitter
that the reassembly process will tolerate.
In case of CESM-8P it should be in increment of 125 micro secs and
Max … | column | Integer32 | .1.3.6.1.4.1.351.110.5.3.2.1.1.1.11 |
| cesCellLossIntegrationPeriod This object specifies the cell loss integration
period. | column | milliseconds Integer32 | .1.3.6.1.4.1.351.110.5.3.2.1.1.1.12 |
| cesChanLocRmtLpbkState Loopback on cellbus in egress direction. | column | Enumeration | .1.3.6.1.4.1.351.110.5.3.2.1.1.1.13 |
| cesChanTestType This is the type of the test
1 = Test Continuity
2 = Test Delay
3 = no test is initated
4 = test continuity with sti cell format
5 = test delay with sti cell format | column | Enumeration | .1.3.6.1.4.1.351.110.5.3.2.1.1.1.14 |
| cesChanTestState This shows the state of the test
1 = Passed
2 = Failed
3 = In Progress
4 = Not In Progress | column | Enumeration | .1.3.6.1.4.1.351.110.5.3.2.1.1.1.15 |
| cesChanRTDResult This is round trip delay time. | column | milliseconds Integer32 | .1.3.6.1.4.1.351.110.5.3.2.1.1.1.16 |
| cesChanPortNum This object refers to the CES logical
port on which channel is created.
The value for this object must be same as the
'cesPortNum' object from cesmPortCnfGrpTable.
… | column | Integer32 | .1.3.6.1.4.1.351.110.5.3.2.1.1.1.17 |
| cesChanConnType This object identifies the type of the connection.
The possible values are :
pvc(1) : Permanent Virtual Connection
svc(2) : Switched Virtual C… | column | Enumeration | .1.3.6.1.4.1.351.110.5.3.2.1.1.1.18 |
| cesChanStrauSciNum This indicates the type of connection.
1 = Normal Channel (nonStrauChannel(0) )
2 = SCI 1 i.e bit 1 & 2
3 = SCI 2 i.e bit 3 & 4
4 = SCI 3 i.e bit 5 & 6
5 = SCI 4 i.e bit 7 & 8
Cur… | column | Enumeration | .1.3.6.1.4.1.351.110.5.3.2.1.1.1.19 |
| cesChanRowStatus This object is used to create,modify or delete an entry
in the table.
A row need to be created using 'add' option. When the
row is successfully created, this object… | column | Enumeration | .1.3.6.1.4.1.351.110.5.3.2.1.1.1.2 |
| cesChanIdleDetEnable This indicates the type of Idle detection enabled
disable(1) : Idle code detection is disabled.
enableOnhookDet(2) : Enable Idle detection wh… | column | Enumeration | .1.3.6.1.4.1.351.110.5.3.2.1.1.1.20 |
| cesChanIdleSignalCode This object identifies the signal code to be sent.
The value indicates the idle pattern in DS0 time slots.
This object is applicable only when cesChanIdleDetEnable object
is set… | column | Integer32 | .1.3.6.1.4.1.351.110.5.3.2.1.1.1.21 |
| cesChanIdleCodeIntgnPeriod This object indicates the Integration period in seconds
This object is applicable only when cesChanIdleDetEnable
is set to enableIdlePatternDet(3). | column | seconds Integer32 | .1.3.6.1.4.1.351.110.5.3.2.1.1.1.22 |
| cesChanOnhookCode This object identifies the on-hook code to be sent.
This object is applicable only when cesChanIdleDetEnable object
is set to enableOnhookDet(2).
The value 0..3 is … | column | Integer32 | .1.3.6.1.4.1.351.110.5.3.2.1.1.1.23 |
| cesChanConditionedData This byte will indicate Idle data to be sent
towards the line whenever channels goes
in to Underrun
Only applicable for CESM-8T1/E1. | column | Integer32 | .1.3.6.1.4.1.351.110.5.3.2.1.1.1.24 |
| cesmChanExtTrgIdleSupp This object is used for disabling/enabling
idle suppression on the connection. This can be set by
external signalling device.
Only applicable to CESM-8T1/E1. | column | Enumeration | .1.3.6.1.4.1.351.110.5.3.2.1.1.1.25 |
| cesmChanConditionedSigCode This byte will indicate Signal code to be sent
sent towards the line whenever channels goes
in to Underrun
Only applicable to CESM-8T1/E1. | column | Integer32 | .1.3.6.1.4.1.351.110.5.3.2.1.1.1.26 |
| cesLocalVpi This object identifies the internal VPI assigned to
a local endpoint, by the switch. The cesLocalVpi,
cesLocalVci and cesLocalNSAP form a unique identifier
for the local connectio… | column | Integer32 | .1.3.6.1.4.1.351.110.5.3.2.1.1.1.27 |
| cesLocalVci This object identifies the internal VCI assigned to
a local endpoint, by the switch. The cesLocalVpi,
cesLocalVci and cesLocalNSAP form a unique identifier
for the local connectio… | column | Integer32 | .1.3.6.1.4.1.351.110.5.3.2.1.1.1.28 |
| cesLocalNSAP This object identifies the internal NSAP
address assigned to local endpoint.
The NSAP address is 20 bytes long and follows the format:
- 13 bytes as prefix 2 bytes for Cisco … | column | OctetString | .1.3.6.1.4.1.351.110.5.3.2.1.1.1.29 |
| cesMapPortNum This object provides the mapping from CES channel number
and physical line number.
In case of CESM-4P this variable specifies the port number
to which this channel… | column | Integer32 | .1.3.6.1.4.1.351.110.5.3.2.1.1.1.3 |
| cesRemoteVpi This object identifies the VPI value of the
peer endpoint. The cesRemoteVpi, cesRemoteVci
and the cesRemoteNSAP identify the peer endpoint(remote) in
the networking domain.
The v… | column | Integer32 | .1.3.6.1.4.1.351.110.5.3.2.1.1.1.30 |
| cesRemoteVci This object identifies the VCI value of the
peer endpoint. The cesRemoteVpi, cesRemoteVci
and the cesRemoteNSAP identify the peer endpoint(remote) in
the networking domain.
The v… | column | Integer32 | .1.3.6.1.4.1.351.110.5.3.2.1.1.1.31 |
| cesMastership This is used by PXM to determine if this end point is
master or slave, a new type unknown(3) is added to identify
the SM in MGX8220(formerly AXIS) shelf and the SM in
MGX8250 sh… | column | Enumeration | .1.3.6.1.4.1.351.110.5.3.2.1.1.1.33 |
| cesVpcFlag This represents the connection type, used for PXM to
identify VPC/VCC but CESM card doesn't use it
always set to vcc for CESM card. | column | Enumeration | .1.3.6.1.4.1.351.110.5.3.2.1.1.1.34 |
| cesConnServiceType This specifies the service type
1 ==> Constant Bit Rate
2 ==> Variable Bit Rate
3 ==> Not used
4 ==> Unspecified Bit Rate
5 ==> ATM frame relay
6 ==> standard ABR
7 ==> foresight… | column | Enumeration | .1.3.6.1.4.1.351.110.5.3.2.1.1.1.35 |
| cesRoutingPriority This is used by PXM to determine how important
this connection is when selecting connections to route. | column | Integer32 | .1.3.6.1.4.1.351.110.5.3.2.1.1.1.36 |
| cesMaxCost This object is used by the networking entity
to select a route based on administrative weight of
possible routes. It is related to Cost Based Routing.
This is used by PXM so that… | column | Integer32 | .1.3.6.1.4.1.351.110.5.3.2.1.1.1.37 |
| cesRestrictTrunkType Restricted trunk type for routing, used by PXM. It
specifies that the connection either cannot be routed over
satelite trunks, or terrestrial trunks, or it can be on
any type of … | column | Enumeration | .1.3.6.1.4.1.351.110.5.3.2.1.1.1.38 |
| cesConnPCR This object identifies the Peak Cell Rate(PCR) value.
If not provided during the row creation, the value
will be computed as follows,
For CESM-8T1/E1 - N * 64 Kbps ,
… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.351.110.5.3.2.1.1.1.39 |
| cesMapVpi The value of this object is equal to the VPI used for the emulated
circuit represented by this connection. In MGX8220( formerly AXIS)
Implementaion slot number of the card will b… | column | Integer32 | .1.3.6.1.4.1.351.110.5.3.2.1.1.1.4 |
| cesConnMCR This object identifies the Minimum Cell Rate(MCR) value.
If not provided during the row creation, the value
will be computed as follows,
For CESM-8T1/E1 - N * 64 Kbps ,
… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.351.110.5.3.2.1.1.1.40 |
| cesConnPercentUtil This is the expected long-term utilization of the
channel by theis end-point.
For CESM-8T1/E1/T3/E3 , the value is 100% | column | Integer32 | .1.3.6.1.4.1.351.110.5.3.2.1.1.1.41 |
| cesmConnRemotePCR The PCR value of the remote end. If not set, the value
for this object is derived from the end point parameter. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.351.110.5.3.2.1.1.1.42 |
| cesmConnRemoteMCR The MCR value of the remote end. If not set, the value
for this object is derived from the end point parameter. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.351.110.5.3.2.1.1.1.43 |
| cesmConnRemotePercentUtil This is the expected long-term utilization of the
channel by the other end-point. | column | Integer32 | .1.3.6.1.4.1.351.110.5.3.2.1.1.1.44 |
| cesmConnForeSightEnable This object is used by the controller(PAR/PNNI/TAG) to set up
the Qbin for the connection.
This is notapplicable to CESM-8T1/E1/T3/E3. | column | Enumeration | .1.3.6.1.4.1.351.110.5.3.2.1.1.1.45 |
| cesmConnFGCRAEnable enables/disables Frame based GCRA (early packet discard).
This is not applicable to CESM-8T1/E1/T3/E3. | column | Enumeration | .1.3.6.1.4.1.351.110.5.3.2.1.1.1.46 |
| cesmChanReroute This is used by the administrator to trigger the re-routing
of the connection. The rerouting takes effect, when this object
is set to true(1). When set to false (2), no action is … | column | Enumeration | .1.3.6.1.4.1.351.110.5.3.2.1.1.1.47 |
| cesmConnAdminStatus This object specifies administrative status of
the connection endpoint.
This object is not applicable to MGX Release 1.x. | column | Enumeration | .1.3.6.1.4.1.351.110.5.3.2.1.1.1.48 |
| cesmChanPrefRouteId This object serves to to associate a preferred
route with a connection.
The value '0' means no preferred route is associated with
this connection.
… | column | Integer32 | .1.3.6.1.4.1.351.110.5.3.2.1.1.1.49 |
| cesMapVci This specifies VCI for emulated circuit represented by this VC.
Our Implementation cesCnfChanNum will be used for this.
In case of CESM-4P valid range is 16..19.
In case of CESM-8… | column | Integer32 | .1.3.6.1.4.1.351.110.5.3.2.1.1.1.5 |
| cesmChanDirectRoute This object serves to associate a prefer
route as directed route (correspond to the prefer route
object cesmChanPrefRouteId).
A directed route specifies that the a… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.351.110.5.3.2.1.1.1.50 |
| cesCBRService This specifies data type supported by the CBR service.
unstructured(1) : This is also known as 'clear channel'.
This service utilizes the entire T… | column | Enumeration | .1.3.6.1.4.1.351.110.5.3.2.1.1.1.6 |
| cesCBRClockMode This specifies clocking mode of the CBR service.
synchronous(1) : The transmit clock frequency is
produced by an external source.
srts (2) : … | column | Enumeration | .1.3.6.1.4.1.351.110.5.3.2.1.1.1.7 |
| cesCas This object specifies whether CAS bits are carried by the service.
This also selects which AAL1 format should be used.
The possible values are :
basi… | column | Enumeration | .1.3.6.1.4.1.351.110.5.3.2.1.1.1.8 |
| cesPartialFill Specifies the number of user octets per cell, if partial
cell fill is used. 47 means partial fill disabled.
Partial fill is not supported in CESM-4P
Ranges for partial fill are:
T… | column | Integer32 | .1.3.6.1.4.1.351.110.5.3.2.1.1.1.9 |