vismAggregateTrafficClipping
CISCO-VISM-MODULE-MIB ·
.1.3.6.1.4.1.351.110.3.17.4.24
Object
scalar
r/w
Enumeration
This attribute defines the aggregate traffic clipping
policy which is applicable to all bearer traffic
generated at VISM card. The applicable options are:
'disable' : aggregate traffic clipping is disabled,
VISM card traffic management does not
perform aggregate traffic clipping.
'enable' : aggregate traffic clipping is enabled,
VISM card traffic management performs
aggregate traffic clipping.
This is applicable to only AAL2 SVC voice bearer traffic.
When aggregate traffic clipping is enabled, VISM card
can discard cells which are exceeding VISM card
aggregate SVC bandwidth which is specified as
vismAggregateSvcBandwidth value.
Context
- MIB
- CISCO-VISM-MODULE-MIB
- OID
.1.3.6.1.4.1.351.110.3.17.4.24- Type
- scalar
- Access
- readwrite
- Status
- current
- Parent
- vismSystemGrp
- Siblings
- 47
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | disable |
2 | enable |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| vismDaughterCardSerialNum A unique value for each VISM daughter card, entered
in nvram by manufacturing. The serial number is on
the non-volatile RAM on the VISM daughter card. | scalar | OctetString | .1.3.6.1.4.1.351.110.3.17.4.1 |
| vismTftpServerDn This object holds the domain name of the tftp server
from where the CAS module will download the CAS files.
This domain name can be resolved internally or externally. … | scalar | OctetString | .1.3.6.1.4.1.351.110.3.17.4.11 |
| vismXgcpBearerNetworkType This object specifies the network type to use in
order to transport bearer traffic.
The user can configure this to IP or ATM based
on where the VISM will be located.
… | scalar | Enumeration | .1.3.6.1.4.1.351.110.3.17.4.12 |
| vismXgcpBearerVCType This object specifies the VC(Virtual Channel) type
to use in order to transport bearer traffic.
If the call agent specifies the VC type in the
MGCP local connection op… | scalar | Enumeration | .1.3.6.1.4.1.351.110.3.17.4.13 |
| vismXgcpBearerConnectionType This object specifies the connection type used
to transport bearer traffic. If the
vismXgcpBearerNetworkType is chosen to be IP
then the value of this object has to be/will
be se… | scalar | Enumeration | .1.3.6.1.4.1.351.110.3.17.4.14 |
| vismBearerContinuityTimer This object specifies the co4 (bearer continuity) timer in
millisecs.
The timer will be started in the terminating/originating
gateway for a duration as specified in th… | scalar | Integer32 | .1.3.6.1.4.1.351.110.3.17.4.15 |
| vismCodecNegotiationOption This object helps in forming an ordered intersection
of lists and one of the lists must be used in determining
the resulting order of codecs.
Lco - local connection op… | scalar | Enumeration | .1.3.6.1.4.1.351.110.3.17.4.16 |
| vismProfileNegotiationOption This object helps in forming an ordered intersection
of lists and one of the lists must be used in determining
the resulting order of profiles.
Lco - local connection… | scalar | Enumeration | .1.3.6.1.4.1.351.110.3.17.4.17 |
| vismCarrierLossPolicy This object defines the policy that needs to be
applied when a carrier loss is detected.
This states whether to switch to the pre-upspeed codec
or to remain with the up… | scalar | Enumeration | .1.3.6.1.4.1.351.110.3.17.4.18 |
| vismCacRejectionPolicy This attribute defines the policy that needs to be
applied once the CAC function rejects the upspeeding
of a connection, due to a fax/modem switch-over
request. The applicable opt… | scalar | Enumeration | .1.3.6.1.4.1.351.110.3.17.4.19 |
| vismDaughterCardDescription This object identifies the VISM daughter card. | scalar | OctetString | .1.3.6.1.4.1.351.110.3.17.4.2 |
| vismExtDnsServerDn This object refers to the domain name of the external
DNS server which will be used to resolve other
domain name.
Currently this domain name can only be resolved
inter… | scalar | OctetString | .1.3.6.1.4.1.351.110.3.17.4.20 |
| vismFeatureBitMap This object denotes the bit map for VISM features. It
indicates the current features that are enabled. It
should be consistent with vismMode. When user change
vismMode, this objec… | scalar | Integer32 | .1.3.6.1.4.1.351.110.3.17.4.21 |
| vismVADTolerance The value in this object refers to the customer
accepted drop rate for voice connections when the
bandwidth usage exceeds allowed value.
The actual range of this object… | scalar | Integer32 | .1.3.6.1.4.1.351.110.3.17.4.22 |
| vismVADDutyCycle This object refers to the talk-spurts duty cycle.
The unit is in percentage.
When the value of this object is to be passed
to underlying CAC module in VISM this value h… | scalar | Integer32 | .1.3.6.1.4.1.351.110.3.17.4.23 |
| vismAggregateSvcBandwidth The aggregate svc bandwidth is used for AAL2 SVC
aggregate SVC CAC and also used for aggregate
traffic clipping at VISM card when
vismAggregateTrafficClipping is enabled.
… | scalar | Integer32 | .1.3.6.1.4.1.351.110.3.17.4.25 |
| vismBearerContinuityTest This attribute defines whether the bearer continuity
test for a connection will be performed at the time of
call setup or not.
When the vismBearerContinuityTest is enab… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.351.110.3.17.4.26 |
| vismCaleaEnable This attribute describes whether CALEA (Communication
Assistance for Law Enforcement Agency) functionality
needs to be enabled on the VISM card. This attribute
enables/disables th… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.351.110.3.17.4.27 |
| vismMaxConfNum Identify how many conference will be supported on a VISM
card | scalar | Integer32 | .1.3.6.1.4.1.351.110.3.17.4.28 |
| vismLongDurationTimer The long duration is the elapse time in hour to
indicate a connection has been established for a
given period of time. The default time is one hour. | scalar | Integer32 | .1.3.6.1.4.1.351.110.3.17.4.29 |
| vismDaughterCardHWRev This object identifies the hardware revision number
for the daughter card. | scalar | OctetString | .1.3.6.1.4.1.351.110.3.17.4.3 |
| vismContinuityCo1Timer A 2010Hz tone is applied, if the co1(Continuity
Tone 1) is specify as a signal the range is
2010Hz +/- 8Hz and if it is specify as an event
the range is 2010Hz +/- 30Hz. The cont… | scalar | Integer32 | .1.3.6.1.4.1.351.110.3.17.4.30 |
| vismContinuityCo2Timer A 1780Hz tone is applied, if the co2(Continuity
Tone 2) is specify as a signal the range is
1780Hz +/- 20Hz and if it is specify as an event
the range is 1780Hz +/- 30Hz. The con… | scalar | Integer32 | .1.3.6.1.4.1.351.110.3.17.4.31 |
| vismReverseCotTone This attribute defines the direction of COT Tone
that is sent in a 2w to 4w arrangement. The VISM
responds to a request from the call agent through
the M:conttest mode, it retur… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.351.110.3.17.4.32 |
| vismSendDnEnable This will allow VISM to send domain name as part
of Audit Enpoint response to the call agent
when it is configured as 'true(1)'. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.351.110.3.17.4.33 |
| vismSendDataGramSize Specify the size of datagram that should be sent
when the vismSendDnEnable is set to 'true(1)'.
Any value greater than the specified size will
be rejected. | scalar | Integer32 | .1.3.6.1.4.1.351.110.3.17.4.34 |
| vismOamLoopThreshold Specify OAM loopback cell loss count before
declaring a PVC alarm. | scalar | Integer32 | .1.3.6.1.4.1.351.110.3.17.4.35 |
| vismFreeDs0Threshold This attribute holds the threshold value of free
DS0 counts on the VISM card. A trap is sent out
if the number of free ds0s fall below this threshold. | scalar | Integer32 | .1.3.6.1.4.1.351.110.3.17.4.36 |
| vismCPUUtilizationThreshold This attribute holds the threshold value of CPU utilization
on the VISM card. A trap is sent out if the CPU utilization
equals or exceeds this threshold. | scalar | Integer32 | .1.3.6.1.4.1.351.110.3.17.4.37 |
| vismMemoryUtilizationThreshold This attribute holds the threshold value of memory
utilization on the VISM card. A trap is sent out if the
memory utilization equals or exceeds this threshold. | scalar | Integer32 | .1.3.6.1.4.1.351.110.3.17.4.38 |
| vismDualToneDetect This object is use to enable/disable dual tone
configuration. When the dual tone is enable and
detected, the Marconi Application will upspeed
to VBD(Voice Band Data) codec. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.351.110.3.17.4.39 |
| vismEcanEncoding The object identifies the voice encoding type,
mu-law or a-law. 'mu-law' is returned for T1 lines
and 'a-law' is returned for E1 lines. | scalar | Enumeration | .1.3.6.1.4.1.351.110.3.17.4.4 |
| vismAisSuppression deprecated This object is used to enable/disable the
AIS(Alarm Indication Signal) suppression
functionality. When AIS suppression is enabled
AIS and RDI(Remote Defect Indication)/FERF(Far En… | scalar | Enumeration | .1.3.6.1.4.1.351.110.3.17.4.40 |
| vismBearerIpPingEnable This object is used to enable/disable the bearer
IP ping response configuration.
When set to true, the bearer IP ping feature will
be enabled on the module and the bearer IP wil… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.351.110.3.17.4.41 |
| vismTrapFilteringEnable This object is used to enable/disable the trap
filtering feature on the module.
When set to true, the trap filtering feature is
enabled on the module.
When set to false, the tra… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.351.110.3.17.4.42 |
| vismSplModemToneBitMap This bit map is applicable for any special modem
tones that need to be enabled or disabled on the module.
If a bit is set to 1, the tone detection is enabled.
If the bit is set… | scalar | Bits | .1.3.6.1.4.1.351.110.3.17.4.43 |
| vismSSRCEnable This object is used to enable/disable more than one
SSRC (Synchronization Source) per RTP session.
When set to true, the module will accept more than
one SSRC per RTP session.
Whe… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.351.110.3.17.4.44 |
| vismOamLoopbackSetCLP This object is used to set the cell loss priority
of the oam loopback cell for all the PVCs.
If set to true, all the CLP bits will be set to 1.
If set to false, all the CLP bit… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.351.110.3.17.4.45 |
| vismPvcAlarmLogEnable This object specifies whether detailed alarm logging
on all the PVC's on the module is enabled or disabled.
If this object is true, detailed alarm logging for all
the PVC's on t… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.351.110.3.17.4.46 |
| vismPvcAlarmLogAdminTimer This object specifies the time for which the detailed
alarm logging for all the PVCs on the module will
remain active.
The value in this object can be set and is valid only
if … | scalar | minutes Unsigned32 | .1.3.6.1.4.1.351.110.3.17.4.47 |
| vismPvcAlarmLogOperTimer This object specifies the time remaining in minutes for
which the detailed alarm logging will remain enabled on
all the PVCs on the module.
When this value becomes 0, it indicat… | scalar | minutes Unsigned32 | .1.3.6.1.4.1.351.110.3.17.4.48 |
| vismContinuityCheckCellEnable This object is used to enable/disable the continuity check
cell for all the PVCs on the module.
If set to true, the module will transmit continuity check
cells.
If set to fals… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.351.110.3.17.4.49 |
| vismMode This attribute defines the connection model that
the VISM card is configured to operate with. This
object can be modified by CLI(Command Line Interface)
only. The CLI 'cnfvismmode… | scalar | Enumeration | .1.3.6.1.4.1.351.110.3.17.4.5 |
| vismPrevMode deprecated This attribute indicates the mode in which VISM was
operating before the object vismMode value was
changed. i.e It gives the value of vismMode before
it got changed to the current… | scalar | Enumeration | .1.3.6.1.4.1.351.110.3.17.4.6 |
| vismCacEnable This attribute describes whether CAC (Connection
Admission Control) functionality needs to be
applied on the VISM card, on a per PVC basis.
For some applications, the CAC function… | scalar | Enumeration | .1.3.6.1.4.1.351.110.3.17.4.7 |
| vismAvailableDs0Count This attribute describes the number of DS0s available
for new connections on VISM. This is modified by the
VISM firmware after each connection is setup. | scalar | Integer32 | .1.3.6.1.4.1.351.110.3.17.4.8 |
| vismAppliedTemplate This attribute describes the Codec template
currently configured on the VISM card. The
value refers to an index to the
vismCodecTemplateCnfGrpTable (defined in
CISCO-VISM-CODEC-M… | scalar | Integer32 | .1.3.6.1.4.1.351.110.3.17.4.9 |