vismEcanTail
CISCO-VISM-DSX1-MIB ·
.1.3.6.1.4.1.351.110.4.3.5.1.1.1.5
Object
column
r/w
milliseconds Integer32
This object identifies the maximum tail. The object
should be set just higher than the worst round trip delay
anticipated. Convergence times may increase for longer
tails and more resource will be used.
Only following discrete values are allowed:
24, 32, 48, 64, 80, 96, 112 and 128.
Context
- MIB
- CISCO-VISM-DSX1-MIB
- OID
.1.3.6.1.4.1.351.110.4.3.5.1.1.1.5- Type
- column
- Access
- readwrite
- Status
- current
- Units
- milliseconds
- Parent
- dsx1VismCnfGrpEntry
- Table
- dsx1VismCnfGrpTable
- Siblings
- 37
Syntax
milliseconds Integer32
Values & Constraints
Object Constraints
range: 24-128
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| vismLineNum This object identifies the DS1/E1 interface number. | column | Integer32 | .1.3.6.1.4.1.351.110.4.3.5.1.1.1.1 |
| vismCadenceTime deprecated This object describes the cadence time for CAS signals.
This object is applicable only for CAS backhaul
applications. For trunking application it is not applicable. | column | milliseconds Integer32 | .1.3.6.1.4.1.351.110.4.3.5.1.1.1.10 |
| vismTrunkConditionEnable This object determines if trunk conditioning should be
enabled or disabled on this line. If this object is
set to true(1), VISM will do trunk conditioning on
the affected DS0s … | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.351.110.4.3.5.1.1.1.11 |
| vismDsx1CircuitIdentifier This object is the identifier of a T1/E1 line.
It contains alphanumeric description of a line for the
purpose of better identification. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.351.110.4.3.5.1.1.1.12 |
| vismDsx1TxDigitOrder When the call agent hands the ANI (Automatic
Number Identification, denoting the calling party number)
and the DNIS (Destination Number Identification Service,
indicating the ca… | column | Enumeration | .1.3.6.1.4.1.351.110.4.3.5.1.1.1.13 |
| vismDsx1TonePlanRegion This object specifies regional tone plan string. If the
value of the object is 'NULL' then it will be considered
non usable, and non 'NULL' is (usable or activated
and related … | column | OctetString | .1.3.6.1.4.1.351.110.4.3.5.1.1.1.14 |
| vismDsx1TonePlanVersion This object will either be considered NULL
(i.e. non usable) or non NULL (usable or activated
and related to an entry in the vismTonePlanTable table).
This object must be compati… | column | Integer32 | .1.3.6.1.4.1.351.110.4.3.5.1.1.1.15 |
| vismDsx1RingingTO Time in seconds for which the ringing cadence will be
generated towards the basic PBX unless interrupted
(e.g. by the answer from the called party or a delete
connection command… | column | seconds Integer32 | .1.3.6.1.4.1.351.110.4.3.5.1.1.1.16 |
| vismDsx1RingBackTO Time in seconds for which the local ring back tone
(towards the TDM) will be generated unless interrupted
(e.g. by the answer from the called party or a delete
connection comma… | column | seconds Integer32 | .1.3.6.1.4.1.351.110.4.3.5.1.1.1.17 |
| vismDsx1BusyTO Time in seconds for which the busy tone will be
generated unless interrupted (e.g. by the hangup from
the calling party). The value Zero indicates that the
tone will be generate… | column | seconds Integer32 | .1.3.6.1.4.1.351.110.4.3.5.1.1.1.18 |
| vismDsx1ReorderTO Time in seconds for which the reorder/fast busy
tone will be generated unless interrupted
(e.g. by the hangup from the calling party). The value
zero indicates that the tone wil… | column | seconds Integer32 | .1.3.6.1.4.1.351.110.4.3.5.1.1.1.19 |
| vismEcanEnabled This object disable/enable echo cancellation.
'disable' : disable echo cancellation.
'enable' : enable echo cancellation. | column | Enumeration | .1.3.6.1.4.1.351.110.4.3.5.1.1.1.2 |
| vismDsx1DialTO Time in seconds for which the dial tone will be
generated unless interrupted (e.g. by the first DTMF
digit from the calling party). The value Zero indicates
that the tone will b… | column | seconds Integer32 | .1.3.6.1.4.1.351.110.4.3.5.1.1.1.20 |
| vismDsx1StutterDialTO Time in seconds for which the stutter dial
tone/confirmation dial tone will be generated unless
interrupted (e.g. by the first DTMF digit from the
calling party). The value Zero … | column | seconds Integer32 | .1.3.6.1.4.1.351.110.4.3.5.1.1.1.21 |
| vismDsx1OffHookAlertTO Time in seconds for which the off-hook alert tone
will be generated unless interrupted (e.g. caller hangup).
The value Zero indicates that the tone will be generated
indefinitel… | column | seconds Integer32 | .1.3.6.1.4.1.351.110.4.3.5.1.1.1.22 |
| vismDsx1RemoteRingback This object specifies the remote ring back method on
endpoints on this DS1/E1.
This object can have the following values:
'proxy(1)': This gateway sends the appro… | column | Enumeration | .1.3.6.1.4.1.351.110.4.3.5.1.1.1.23 |
| vismDsx1MidcallTpart This object represents the partial dial timing in
seconds and is used along with a digit map as the
inter-digit timer. This object is used for both CAS
and non CAS endpoints when… | column | seconds Integer32 | .1.3.6.1.4.1.351.110.4.3.5.1.1.1.24 |
| vismDsx1MidcallTcrit This object represents the critical timing in seconds.
If used along with a digit map, the timer is started when
the last digit is received i.e when no more digits
are required fo… | column | seconds Integer32 | .1.3.6.1.4.1.351.110.4.3.5.1.1.1.25 |
| vismDsx1Sa4Byte This is a spare bit on T1/E1 Framer reserved for
international standardization. | column | Integer32 | .1.3.6.1.4.1.351.110.4.3.5.1.1.1.26 |
| vismDsx1Sa5Byte This is a spare bit on T1/E1 Framer reserved for
international standardization. | column | Integer32 | .1.3.6.1.4.1.351.110.4.3.5.1.1.1.27 |
| vismDsx1Sa6Byte This is a spare bit on T1/E1 Framer reserved for
international standardization. | column | Integer32 | .1.3.6.1.4.1.351.110.4.3.5.1.1.1.28 |
| vismDsx1Sa7Byte This is a spare bit on T1/E1 Framer reserved for
international standardization. | column | Integer32 | .1.3.6.1.4.1.351.110.4.3.5.1.1.1.29 |
| vismEcanToneDisable deprecated This object determines the behavior of the echo canceler
in the presence of a modem.
'ignore': Ignore 2100 Hz modem answer tone.
'g-164' : G-164 mode, disable the c… | column | Enumeration | .1.3.6.1.4.1.351.110.4.3.5.1.1.1.3 |
| vismDsx1Sa8Byte This is a spare bit on T1/E1 Framer reserved for
international standardization. | column | Integer32 | .1.3.6.1.4.1.351.110.4.3.5.1.1.1.30 |
| vismDsx1State This object will allow the line administrative state
(in service and out of service) to be persistent.
invalid (1) : invalid state.
is (2) : in service
oos (3) : out of s… | column | Enumeration | .1.3.6.1.4.1.351.110.4.3.5.1.1.1.31 |
| vismDsx1AdminStateControl This control object is used to change the service state of the
line from 'is' to 'coos' or from 'coos'
to 'is'. The resulting service state of the line is
represented by vismDsx1S… | column | Enumeration | .1.3.6.1.4.1.351.110.4.3.5.1.1.1.32 |
| vismBearerBusyCode This object is used when vismTrunkConditionEnable is
enabled on a line. It is a configurable busy pattern
sent out on the 'Bearer' on the channels, which are
receiving remote ATM … | column | Integer32 | .1.3.6.1.4.1.351.110.4.3.5.1.1.1.33 |
| vismDsx1V110Enable This object specifies whether V.110 detection on the
line is enabled or disabled.
If the value of this object is 'true', V.110 detection
on the line is enabled.
If the value of t… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.351.110.4.3.5.1.1.1.34 |
| vismDsx1AlarmLogEnable This object specifies whether detailed alarm logging
on the DS1 is enabled or disabled.
If this object is true, detailed alarm logging for
the DS1 will be enabled.
If this objec… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.351.110.4.3.5.1.1.1.35 |
| vismDsx1AlarmLogAdminTimer This object specifies the time for which the detailed
alarm logging for the DS1 will remain active.
The value in this object can be set and is valid only
if vismDsx1AlarmLogEnab… | column | minutes Unsigned32 | .1.3.6.1.4.1.351.110.4.3.5.1.1.1.36 |
| vismDsx1AlarmLogOperTimer This object specifies the time remaining in minutes for
which the detailed alarm logging will remain active on
the DS1.
When this value becomes 0, it indicates that the DS1
has… | column | minutes Unsigned32 | .1.3.6.1.4.1.351.110.4.3.5.1.1.1.37 |
| vismDsx1ElectricalSignalEnable This object specifies whether electrical signal on the
line is enabled or disabled.
If the value of this object is 'true', electrical signal
on the line is enabled.
If the value … | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.351.110.4.3.5.1.1.1.38 |
| vismEcanCnfNRN deprecated Echo canceler re-enable (NRN). This object
determines when an echo canceler re-enable
and begins cancellation after it has been
disabled.
'reenableOnModemData': Re-… | column | Enumeration | .1.3.6.1.4.1.351.110.4.3.5.1.1.1.4 |
| vismEcanREC Residual Echo Control (REC) instructs the canceler
how to treat echo remaining after cancellation.
'cancelOnly' : REC is disabled.
'suppressResidual': The resi… | column | Enumeration | .1.3.6.1.4.1.351.110.4.3.5.1.1.1.6 |
| vismCompCnfVAD This object identifies VAD (Voice Activity Detection).
'disable': Disable VAD on the compression DSPs.
'enable' : Enable VAD on the compression DSPs. | column | Enumeration | .1.3.6.1.4.1.351.110.4.3.5.1.1.1.7 |
| vismSignalingType This object specifies the type of signaling used for
the line.
'cas' : Channel Associated Signaling.
'ccs' : Common Channel Signaling.
'none' : No signaling used… | column | Enumeration | .1.3.6.1.4.1.351.110.4.3.5.1.1.1.8 |
| vismCcsChannels This object describes the CCS signaling channels or
DS0s (also referred to as D-channel).
It is used only for lines configured as CCS signaling type.
It is a bit map of the DS0… | column | Integer32 | .1.3.6.1.4.1.351.110.4.3.5.1.1.1.9 |