cufwFOUnitDesignation

CISCO-UNIFIED-FIREWALL-MIB · .1.3.6.1.4.1.9.9.491.1.4.1.2
MIB view Table view

Object

scalar CISCO-FIREWALL-MIBHardware 
The hardware type that points to designation as primary
or secondary unit.

Context

MIB
CISCO-UNIFIED-FIREWALL-MIB
OID
.1.3.6.1.4.1.9.9.491.1.4.1.2
Type
scalar
Access
readonly
Status
current
Parent
cuFwFailoverGlobals
Siblings
19

Syntax

CISCO-FIREWALL-MIBHardware
Source
CISCO-FIREWALL-MIBHardware
Base type
Enumeration

Values & Constraints

Type Values
1memory
2disk
3power
4netInterface
5cpu
6primaryUnit
7secondaryUnit
8other

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
cufwFOEnabled
This value depicts if failover is enabled or not on the device.
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.491.1.4.1.1
cufwFOSwVersionMate
The vendor-specific software revision string for the peer unit in pair.
scalarSNMP-FRAMEWORK-MIBSnmpAdminString.1.3.6.1.4.1.9.9.491.1.4.1.10
cufwFOUnitPolltime
The polling frequency of the Hello packets between the units in HA pair.
scalarmillisec Integer32.1.3.6.1.4.1.9.9.491.1.4.1.11
cufwFOUnitHoldtime
The hold time that each unit will wait before declaring the peer unit as dead. If the failed unit is the active unit, the standby unit takes over as the active unit.
scalarmillisec Integer32.1.3.6.1.4.1.9.9.491.1.4.1.12
cufwFOUnitBfdEnabled
This object depicts if BFD protocol is enabled between the units for health monitoring.
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.491.1.4.1.13
cufwFOLinkStatePolltime
The frequency at which the link-state of a unit's interfaces are polled to detect link failures.
scalarmillisec Integer32.1.3.6.1.4.1.9.9.491.1.4.1.14
cufwFOInterfacePolicy
The count of interface failures set as threshold to trigger switchover when interfaces are declared as health-check failed.
scalarInteger32.1.3.6.1.4.1.9.9.491.1.4.1.15
cufwFOMonitoredInterfaces
The count of interfaces monitored on the HA units for interface health.
scalarSNMPv2-SMIGauge32.1.3.6.1.4.1.9.9.491.1.4.1.16
cufwFOInterfacePolltime
The polling frequency of the Hello packets on each interface between the units in HA pair.
scalarmillisec Integer32.1.3.6.1.4.1.9.9.491.1.4.1.17
cufwFOInterfaceHoldtime
The hold time that each unit will wait before declaring the peer unit as dead due to interface check failure.
scalarmillisec Integer32.1.3.6.1.4.1.9.9.491.1.4.1.18
cufwFOReplicationHttp
This object depicts if the stateful replication of HTTP sessions is enabled in a Stateful Failover environment.
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.491.1.4.1.19
cufwFOReplicationRate
The bulk-sync connection replication rate between the HA units.
scalarConnections Per Second SNMPv2-SMIGauge32.1.3.6.1.4.1.9.9.491.1.4.1.20
cufwFOLink
The ifIndex of the interface used for failover communication between the two units.
scalarIF-MIBInterfaceIndex.1.3.6.1.4.1.9.9.491.1.4.1.3
cufwFOStateLink
The ifIndex of the interface used for failover communication to pass connection state information.
scalarIF-MIBInterfaceIndex.1.3.6.1.4.1.9.9.491.1.4.1.4
cufwFOStdbyConfigLocked
This object depicts if the the ability to make any configuration changes directly on the standby unit or context is enabled.
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.491.1.4.1.5
cufwFOEncryption
The type of encryption enabled on the failover links between the units to encrypt all failover communications. Value Type 0 none 1 …
scalarInteger32.1.3.6.1.4.1.9.9.491.1.4.1.6
cufwFOSerialNumOurs
The vendor-specific serial number string for the current unit in pair.
scalarSNMP-FRAMEWORK-MIBSnmpAdminString.1.3.6.1.4.1.9.9.491.1.4.1.7
cufwFOSerialNumMate
The vendor-specific serial number string for the peer unit in pair.
scalarSNMP-FRAMEWORK-MIBSnmpAdminString.1.3.6.1.4.1.9.9.491.1.4.1.8
cufwFOSwVersionOurs
The vendor-specific software revision string for the current unit in pair.
scalarSNMP-FRAMEWORK-MIBSnmpAdminString.1.3.6.1.4.1.9.9.491.1.4.1.9