cufwFOEncryption
CISCO-UNIFIED-FIREWALL-MIB ·
.1.3.6.1.4.1.9.9.491.1.4.1.6
Object
scalar
Integer32
The type of encryption enabled
on the failover links between the units to encrypt all failover
communications.
Value Type
0 none
1 IPSec LAN-to-LAN tunnels
2 Key Passphrase
Context
- MIB
- CISCO-UNIFIED-FIREWALL-MIB
- OID
.1.3.6.1.4.1.9.9.491.1.4.1.6- Type
- scalar
- Access
- readonly
- Status
- current
- Parent
- cuFwFailoverGlobals
- Siblings
- 19
Syntax
Integer32
Values & Constraints
Object Constraints
range: 0-2
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| cufwFOEnabled This value depicts if failover is enabled or not
on the device. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.491.1.4.1.1 |
| cufwFOSwVersionMate The vendor-specific software revision string for the
peer unit in pair. | scalar | SNMP-FRAMEWORK-MIBSnmpAdminString | .1.3.6.1.4.1.9.9.491.1.4.1.10 |
| cufwFOUnitPolltime The polling frequency of the Hello packets
between the units in HA pair. | scalar | millisec Integer32 | .1.3.6.1.4.1.9.9.491.1.4.1.11 |
| cufwFOUnitHoldtime The hold time that each unit will wait before
declaring the peer unit as dead. If the failed unit is the active unit,
the standby unit takes over as the active unit. | scalar | millisec Integer32 | .1.3.6.1.4.1.9.9.491.1.4.1.12 |
| cufwFOUnitBfdEnabled This object depicts if BFD protocol is enabled between the units for
health monitoring. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.491.1.4.1.13 |
| cufwFOLinkStatePolltime The frequency at which the link-state of a unit's
interfaces are polled to detect link failures. | scalar | millisec Integer32 | .1.3.6.1.4.1.9.9.491.1.4.1.14 |
| cufwFOInterfacePolicy The count of interface failures set as threshold to trigger switchover when interfaces
are declared as health-check failed. | scalar | Integer32 | .1.3.6.1.4.1.9.9.491.1.4.1.15 |
| cufwFOMonitoredInterfaces The count of interfaces monitored on the HA units for interface health. | scalar | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.9.9.491.1.4.1.16 |
| cufwFOInterfacePolltime The polling frequency of the Hello packets
on each interface between the units in HA pair. | scalar | millisec Integer32 | .1.3.6.1.4.1.9.9.491.1.4.1.17 |
| cufwFOInterfaceHoldtime The hold time that each unit will wait before
declaring the peer unit as dead due to interface check failure. | scalar | millisec Integer32 | .1.3.6.1.4.1.9.9.491.1.4.1.18 |
| cufwFOReplicationHttp This object depicts if the stateful replication of HTTP
sessions is enabled in a Stateful Failover environment. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.491.1.4.1.19 |
| cufwFOUnitDesignation The hardware type that points to designation as primary
or secondary unit. | scalar | CISCO-FIREWALL-MIBHardware | .1.3.6.1.4.1.9.9.491.1.4.1.2 |
| cufwFOReplicationRate The bulk-sync connection replication rate between the HA units. | scalar | Connections Per Second SNMPv2-SMIGauge32 | .1.3.6.1.4.1.9.9.491.1.4.1.20 |
| cufwFOLink The ifIndex of the interface used for failover communication
between the two units. | scalar | IF-MIBInterfaceIndex | .1.3.6.1.4.1.9.9.491.1.4.1.3 |
| cufwFOStateLink The ifIndex of the interface used for failover communication
to pass connection state information. | scalar | IF-MIBInterfaceIndex | .1.3.6.1.4.1.9.9.491.1.4.1.4 |
| cufwFOStdbyConfigLocked This object depicts if the the ability to make any configuration
changes directly on the standby unit or context is enabled. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.491.1.4.1.5 |
| cufwFOSerialNumOurs The vendor-specific serial number string for the
current unit in pair. | scalar | SNMP-FRAMEWORK-MIBSnmpAdminString | .1.3.6.1.4.1.9.9.491.1.4.1.7 |
| cufwFOSerialNumMate The vendor-specific serial number string for the
peer unit in pair. | scalar | SNMP-FRAMEWORK-MIBSnmpAdminString | .1.3.6.1.4.1.9.9.491.1.4.1.8 |
| cufwFOSwVersionOurs The vendor-specific software revision string for the
current unit in pair. | scalar | SNMP-FRAMEWORK-MIBSnmpAdminString | .1.3.6.1.4.1.9.9.491.1.4.1.9 |