ciscoTsPortCfgSpanningTreeMode
CISCO-TS-STACK-MIB ·
.1.3.6.1.4.1.9.5.32.4.1.1.25
Object
column
mandatory
r/w
Enumeration
Used when configuring manual spanning tree. Setting this object to forwarding(2) or blocking(3) overrides the TrCRF's spanning tree's algorithm for this port.
Context
- MIB
- CISCO-TS-STACK-MIB
- OID
.1.3.6.1.4.1.9.5.32.4.1.1.25- Type
- column
- Access
- readwrite
- Status
- mandatory
- Parent
- ciscoTsPortCfgEntry
- Table
- ciscoTsPortCfgTable
- Siblings
- 28
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | auto |
2 | forwarding |
3 | blocking |
4 | unknown |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| ciscoTsPortCfgNumber mandatory A unique value for each port entry. The value
corresponds the port number. | column | Integer32 | .1.3.6.1.4.1.9.5.32.4.1.1.1 |
| ciscoTsPortCfgErrSampling mandatory Error sampling interval in minutes. | column | Integer32 | .1.3.6.1.4.1.9.5.32.4.1.1.10 |
| ciscoTsPortCfgMaxTransmitUnit mandatory MTU size. The valid values for this object are 1500,
4472, 8144 and 17800. The value specified cannot exceed
the vtpVlanMTU (see Cisco VTP MIB) for the TrBRF that
this port is a… | column | Integer32 | .1.3.6.1.4.1.9.5.32.4.1.1.11 |
| ciscoTsPortCfgMaxExplorerRate mandatory Explorer frame forwarding rate per second throttle.
A value of (-1) disables explorer frame throttling. | column | Integer32 | .1.3.6.1.4.1.9.5.32.4.1.1.12 |
| ciscoTsPortCfgSetACbits mandatory Specifies if the AC bits shall be set unconditionally
when a port forwards certain LLC frames. | column | Enumeration | .1.3.6.1.4.1.9.5.32.4.1.1.13 |
| ciscoTsPortCfgEarlyTokenRlse mandatory Early token release operation. | column | Enumeration | .1.3.6.1.4.1.9.5.32.4.1.1.14 |
| ciscoTsPortCfgForwardingMode mandatory Operational frame switching mode for the port. When in
auto mode the port uses the Direct Cut algorithm to place
the port in either cutthru(3) or storeandforward(2) mode. | column | Enumeration | .1.3.6.1.4.1.9.5.32.4.1.1.15 |
| ciscoTsPortCfgActualForwardingMode mandatory Actual operational frame switching mode for the port. | column | Enumeration | .1.3.6.1.4.1.9.5.32.4.1.1.16 |
| ciscoTsPortCfgPortMode mandatory Port operation mode. Only the HDX and FDX modes can be
auto detected. Note, that passive-probe(7) mode can not be
set with this object. The passive-probe(7) mode is set
automatic… | column | Enumeration | .1.3.6.1.4.1.9.5.32.4.1.1.17 |
| ciscoTsPortCfgActualPortMode mandatory The actual port operation mode. If the port is in auto mode,
this object will return the mode that the port opened in. | column | Enumeration | .1.3.6.1.4.1.9.5.32.4.1.1.18 |
| ciscoTsPortCfgPriorityThres mandatory The highest token-ring frame priority that shall go to
the low-priority transmit queue. | column | Integer32 | .1.3.6.1.4.1.9.5.32.4.1.1.19 |
| ciscoTsPortCfgModNumber mandatory Module number of the module that contains this port. | column | Integer32 | .1.3.6.1.4.1.9.5.32.4.1.1.2 |
| ciscoTsPortCfgMinXmitPriority mandatory The minimum token priority that will be used for
transmit. | column | Integer32 | .1.3.6.1.4.1.9.5.32.4.1.1.20 |
| ciscoTsPortCfgCfgLossThres mandatory Number of configuration loss events (described in
TsPortCfgLossRC) during the sample period which, if
exceeded, should cause the port to be disabled. If the
port is disabled by th… | column | Integer32 | .1.3.6.1.4.1.9.5.32.4.1.1.21 |
| ciscoTsPortCfgCfgLossInterval mandatory The sampling period, in minutes, for which the port
monitors to determine if the configuration loss threshold has
been exceeded. | column | Integer32 | .1.3.6.1.4.1.9.5.32.4.1.1.22 |
| ciscoTsPortCfgBcastSuppresion mandatory The number of broadcast frames per second allowed to be
forwarded by this port. Any broadcast frames exceeding
this watermark will not be forwarded by the port. Setting this
obje… | column | Integer32 | .1.3.6.1.4.1.9.5.32.4.1.1.23 |
| ciscoTsPortCfgCDPTimeToLive mandatory The advertised time-to-live parameter on all CDP messages
generated by this switch on this port. | column | Integer32 | .1.3.6.1.4.1.9.5.32.4.1.1.24 |
| ciscoTsPortCfgSecurityMode mandatory Port security mode is used to disable address learning
at a port where an allow-source or allow-destination
MAC address filter is configured. A value of normal(1)
indicates that … | column | Enumeration | .1.3.6.1.4.1.9.5.32.4.1.1.26 |
| ciscoTsPortCfgSoftErrThreshold mandatory The number of soft errors reported from a station
connected to this port which, if exceeded, should
cause a soft error exceeded trap to be issued. The
error counters being monito… | column | Integer32 | .1.3.6.1.4.1.9.5.32.4.1.1.27 |
| ciscoTsPortCfgSoftErrReportInterval mandatory The sampling period, in seconds, in which each station
connected to this port will be monitored for excessive
soft error reports. If a station reports more than
ciscoTsPortCfgSoft… | column | Integer32 | .1.3.6.1.4.1.9.5.32.4.1.1.28 |
| ciscoTsPortCfgSoftErrorMonitoring mandatory Used to enable or disable, for this port, the collection
of soft error statistics and the sending of traps when
the configured error threshold is exceeded. If RMON
statistics col… | column | Enumeration | .1.3.6.1.4.1.9.5.32.4.1.1.29 |
| ciscoTsPortCfgIfIndex mandatory A pointer to the entry in the ifTable corresponding
to this port. | column | Integer32 | .1.3.6.1.4.1.9.5.32.4.1.1.3 |
| ciscoTsPortCfgResetStats mandatory Setting this object to reset(3) causes all
traffic counters for this port to be set to zero.
Also the value of ciscoTsPortStatsResetTimer is set to
zero. | column | Enumeration | .1.3.6.1.4.1.9.5.32.4.1.1.4 |
| ciscoTsPortCfgResetAddrs mandatory Setting this object to reset(3) clears all
address table entries for this port as well as
setting all port traffic counters to zero and
setting ciscoTsPortStatsResetTimer to zero. | column | Enumeration | .1.3.6.1.4.1.9.5.32.4.1.1.5 |
| ciscoTsPortCfgAddrAgingTime mandatory Port level address aging time in minutes. Setting this object
to zero disables address aging. | column | Integer32 | .1.3.6.1.4.1.9.5.32.4.1.1.6 |
| ciscoTsPortCfgDemandAgingLevel mandatory Threshold to demand age the port address table. All
numbers refer to percentage of the address table. The
only values accepted by the agent are 50,60,70,80,90
and 0. Setting the v… | column | Integer32 | .1.3.6.1.4.1.9.5.32.4.1.1.7 |
| ciscoTsPortCfgErrLoThreshold mandatory Lower error rate threshold which causes the port to
transition from store and forward mode to cut-through mode. | column | Integer32 | .1.3.6.1.4.1.9.5.32.4.1.1.8 |
| ciscoTsPortCfgErrHiThreshold mandatory Upper error rate threshold which causes the port to
transition from cut-through mode to store and forward mode. | column | Integer32 | .1.3.6.1.4.1.9.5.32.4.1.1.9 |