cseSysUpTime
CISCO-SYSTEM-EXT-MIB ·
.1.3.6.1.4.1.9.9.305.1.1.10
Object
The time (in seconds) since the entire system was last re-initialized as a result of reload. The initialization being system loaded and running with a system image software on the first active supervisor (SUP). In High Availibility (HA) capable system / System that provides Supervisor module redundancy, this uptime indicates time elapsed since the first active SUP was booted. This will not change even if the active SUP goes down and stand-by takes over as active.
Context
- MIB
- CISCO-SYSTEM-EXT-MIB
- OID
.1.3.6.1.4.1.9.9.305.1.1.10- Type
- scalar
- Access
- readonly
- Status
- current
- Units
- Seconds
- Parent
- ciscoSysInfoGroup
- Siblings
- 9
Values & Constraints
No enumerated values or constraints recorded.
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| cseSysCPUUtilization The average utilization of CPU on the active
supervisor. | scalar | % Unsigned32 | .1.3.6.1.4.1.9.9.305.1.1.1 |
| cseSysMemoryUtilization The average utilization of memory on the active
supervisor. | scalar | % Unsigned32 | .1.3.6.1.4.1.9.9.305.1.1.2 |
| cseSysConfLastChange The local date and time when the
configuration was last changed. This object will
be set to zero on power cycle or on reboot of
the system. Also, if the clock is changed on
loc… | scalar | SNMPv2-TCDateAndTime | .1.3.6.1.4.1.9.9.305.1.1.3 |
| cseSysAutoSync The state of the auto synchronization of images
between the active and standby supervisor.
Setting the value to sync when the existing value
is sync, has no effect on the operatio… | scalar | Enumeration | .1.3.6.1.4.1.9.9.305.1.1.4 |
| cseSysAutoSyncState The status of the current auto synchronization
process, or if no such process is in progress,
then the state of the most recent one. The
value 'notStarted' indicates no auto s… | scalar | Enumeration | .1.3.6.1.4.1.9.9.305.1.1.5 |
| cseWriteErase This object is used to initiate a write erase on the
device's saved configuration file(s) from which the
device loads its configuration when it restarts.
If the value … | scalar | Enumeration | .1.3.6.1.4.1.9.9.305.1.1.6 |
| cseSysConsolePortStatus This object describes the status of the console
port on this device.
The status 'connected' means that there is
a cable attached to the console port.
The s… | scalar | Enumeration | .1.3.6.1.4.1.9.9.305.1.1.7 |
| cseSysTelnetServiceActivation Enables or disables the Telnet service on the
device. In other words, it enables or disables
the telneting to the device. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.305.1.1.8 |
| cseSysFIPSModeActivation The object to enable/disable FIPS mode on the device.
FIPS 140-2 is a set of security requirements for cryptographic
modules and it details the U.S. Government requirements for
c… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.305.1.1.9 |