coIfXcvrLSCPulseRepetitionTime
CISCO-OPTICAL-IF-EXTN-MIB ·
.1.3.6.1.4.1.9.10.66.1.4.1.1.13
Object
column
r/w
seconds Unsigned32
This object specifies the delay interval between transmissions of restart pulses, when coIfXcvrLSCRestartMode is set to 'automaticRestart' and coIfXcvrLaserOperStatus indicates 'lscDown'.
Context
- MIB
- CISCO-OPTICAL-IF-EXTN-MIB
- OID
.1.3.6.1.4.1.9.10.66.1.4.1.1.13- Type
- column
- Access
- readwrite
- Status
- current
- Units
- seconds
- Parent
- coIfXcvrEntry
- Table
- coIfXcvrTable
- Siblings
- 12
Syntax
seconds Unsigned32
Values & Constraints
Object Constraints
range: 1-300
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| coIfXcvrLaserAdminStatus The desired state of the laser on this interface.
This object differs from ifAdminStatus in the IF-MIB, since
in some cases setting ifAdminStatus to 'down' causes a… | column | Enumeration | .1.3.6.1.4.1.9.10.66.1.4.1.1.1 |
| coIfXcvrLSCManualRestart This object initiates laser activation when the laser is shut
down due to Laser Safety Control.
When the value is set to 'restart', transmission of a restart
pulse … | column | Enumeration | .1.3.6.1.4.1.9.10.66.1.4.1.1.10 |
| coIfXcvrLSCPulseLength This object specifies the length of restart pulses used to
restore transmission when a Laser Safety Control protocol is
activated. | column | milliseconds Unsigned32 | .1.3.6.1.4.1.9.10.66.1.4.1.1.11 |
| coIfXcvrLSCTestPulseLength This object specifies the length of test restart pulses that
are transmitted when coIfXcvrLSCManualRestart is set to
'restartForTest'. | column | seconds Unsigned32 | .1.3.6.1.4.1.9.10.66.1.4.1.1.12 |
| coIfXcvrLaserOperStatus This object indicates the current operational status of the
laser on this interface.
'transmitting': The laser is on.
'degraded': The laser is on, bu… | column | Enumeration | .1.3.6.1.4.1.9.10.66.1.4.1.1.2 |
| coIfXcvrMinLaserFrequency The lowest frequency represented in the bitmap specified in
coIfXcvrLaserFrequencyBitmap, i.e., the frequency represented
by bit 0 of octet 1 of coIfXcvrLaserFrequencyBitmap.
… | column | GHz CoDwdmFrequencyOrZero | .1.3.6.1.4.1.9.10.66.1.4.1.1.3 |
| coIfXcvrLaserFrequencySpacing The difference in frequency between successive bits in
coIfXcvrLaserFrequencyBitmap. This is typically the frequency
difference between adjacent channels in the DWDM system. | column | GHz Unsigned32 | .1.3.6.1.4.1.9.10.66.1.4.1.1.4 |
| coIfXcvrLaserFrequencyBitmap This bitmap indicates the DWDM channel frequencies supported
by the tunable laser on this interface.
Bit zero of octet one corresponds to the lowest channel
(repres… | column | OctetString | .1.3.6.1.4.1.9.10.66.1.4.1.1.5 |
| coIfXcvrForwardLaserControl This object is used to enable or disable Forward Laser Control
(FLC) on this interface. If Forward Laser Control is enabled,
the laser is automatically shut down when the receive… | column | Enumeration | .1.3.6.1.4.1.9.10.66.1.4.1.1.6 |
| coIfXcvrLaserSafetyControl This object is used to enable or disable Laser Safety Control
(LSC) mechanisms such as Automatic Laser Shutdown (ALS) on this
interface. Laser Safety Control mechanisms are used … | column | Enumeration | .1.3.6.1.4.1.9.10.66.1.4.1.1.7 |
| coIfXcvrLSCProtocol This object identifies the Laser Safety Control protocol that
is applied when coIfXcvrLaserSafetyControl is set to 'enable'.
'proprietary': Indicates that the Laser… | column | Enumeration | .1.3.6.1.4.1.9.10.66.1.4.1.1.8 |
| coIfXcvrLSCRestartMode This object selects the mechanism used to restore transmission
after the fiber has been repaired or reconnected.
'automaticRestart': This mode selects automatic res… | column | Enumeration | .1.3.6.1.4.1.9.10.66.1.4.1.1.9 |