dsx3bertLoopback
CISCO-MGX82XX-DSX3-BERT-MIB ·
.1.3.6.1.4.1.351.110.6.2.11
Object
scalar
r/w
Enumeration
This object specifies the type of loopback to be established/de-established. The value farEndLoopback(1) is not supported in CESM-T3E3 and FRSM-2T3E3, where the default value for this object shall be 2.
Context
- MIB
- CISCO-MGX82XX-DSX3-BERT-MIB
- OID
.1.3.6.1.4.1.351.110.6.2.11- Type
- scalar
- Access
- readwrite
- Status
- current
- Parent
- dsx3bert
- Siblings
- 19
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | farEndLoopback |
2 | metallicLoopback |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| dsx3bertControl This object controls all the SET operations on this MIB group.
noAction : No action is taken. This value can not be written
This object contains value noAction… | scalar | Enumeration | .1.3.6.1.4.1.351.110.6.2.1 |
| dsx3bertPattern This variable determines BERT pattern to be transmitted
on the interface identified by dsx3bertLine or dsx3bertPort.
Bit error measurements are widely used to assess t… | scalar | Enumeration | .1.3.6.1.4.1.351.110.6.2.10 |
| dsx3bertStartTime This object contains the time at which
BERT started. The syntax is hh:mm:ss.
The time zone is as configured in the shelf.
This object contains zero length string for fo… | scalar | OctetString | .1.3.6.1.4.1.351.110.6.2.12 |
| dsx3bertStartDate This object contains the date on which
BERT started. The syntax is yy/mm/dd.
This object contains zero length string for following
values of dsx3bertControl:
noActio… | scalar | OctetString | .1.3.6.1.4.1.351.110.6.2.13 |
| dsx3bertBitCountUpper This number of bits transmitted is represented in an encoded
form as a 64-bit counter. This object gives the upper 31 bits
of the 64 bit counter. The 32nd bit is not available. | scalar | Integer32 | .1.3.6.1.4.1.351.110.6.2.14 |
| dsx3bertBitCountLower This number of bits transmitted is represented in an encoded
form as a 64-bit counter. This object gives the lower 31 bits
of the 64 bit counter. The 32nd bit is not available. | scalar | Integer32 | .1.3.6.1.4.1.351.110.6.2.15 |
| dsx3bertBitErrorCountUpper This number of bits received in error is represented in
an encoded form as a 64-bit counter. This object gives the
upper 31 bits of the 64 bit counter. The 32nd bit is not
avail… | scalar | Integer32 | .1.3.6.1.4.1.351.110.6.2.16 |
| dsx3bertBitErrorCountLower This number of bits received in error is represented in
an encoded form as a 64-bit counter. This object gives the
lower 31 bits of the 64 bit counter. The 32nd bit is not
avai… | scalar | Integer32 | .1.3.6.1.4.1.351.110.6.2.17 |
| dsx3bertErrorInsertionRate This object is used for injecting continuous errors into
transmitted BERT pattern. The errors are inserted in a BERT
pattern sent, in order to do sanity check on receive interf… | scalar | Enumeration | .1.3.6.1.4.1.351.110.6.2.18 |
| dsx3bertErrorInjectCount This shows the number of times error was injected. | scalar | Integer32 | .1.3.6.1.4.1.351.110.6.2.19 |
| dsx3bertResourceStatus All of bert resources can be used by only one user at a time.
This object provides the status of the resources. | scalar | Enumeration | .1.3.6.1.4.1.351.110.6.2.2 |
| dsx3bertCleanupAction When the BERT has to be stopped or aborted (due to card state
changes), this object would give the exact action to take.
The bert related changes to the card, then, can be clea… | scalar | Enumeration | .1.3.6.1.4.1.351.110.6.2.20 |
| dsx3bertOwner This refers to the user who owns the BERT resources.
If the user is a CLI user, then this is username.
If it is SNMP Manager, then this would be the ASCII
form of the IP address. | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.351.110.6.2.3 |
| dsx3bertUserId This identifies the user who wants to do a SET operation
on this group. This will be compared against bertOwner
and access will be given only if it matches. Hence, for
every SET r… | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.351.110.6.2.4 |
| dsx3bertStatus This object provides the status of BERT in the shelf.
The possible values are :
inactive (1) : BERT not in progress
bertInSync (2) : BERT is activated and r… | scalar | Enumeration | .1.3.6.1.4.1.351.110.6.2.5 |
| dsx3bertTestMedium Specifies whether the BERT is to be tested on a port or an
entire T3/E3 line.
For a BERT test, this object must be set.
For CESM-T3E3 and FRSM-@T3E3, this object must be set
to l… | scalar | Enumeration | .1.3.6.1.4.1.351.110.6.2.6 |
| dsx3bertPort This object specifies the port number for BERT.
Port level bert is not supported in CESM-T3E3 and
FRSM-2T3E3. So for these cards, the value must be always 1. | scalar | Integer32 | .1.3.6.1.4.1.351.110.6.2.7 |
| dsx3bertLine This object specifies the line number for BERT.
If the dsx3bertTestMedium is set to port(1),
this represents the line to which the port
(dsx3bertPort) belongs.
The value supported… | scalar | Integer32 | .1.3.6.1.4.1.351.110.6.2.8 |
| dsx3bertMode This object specifies the mode, the BERT module is to be
configured for.
The value loopback(2) is not supported in CESM-T3E3 and FRSM-2T3E3 . | scalar | Enumeration | .1.3.6.1.4.1.351.110.6.2.9 |