cmedxProfileInGainControl
CISCO-MEGACO-EXT-MIB ·
.1.3.6.1.4.1.9.10.104.1.1.3.1.13
Object
column
r/w
dB Integer32
This object contains the amount of gain inserted at the receiver side of the interface. The input gain settings only define a gain/loss relative to the 0 dB setting. The absolute loss at the 0 dB setting could be implementation dependent based on the desired network loss plan.
Context
- MIB
- CISCO-MEGACO-EXT-MIB
- OID
.1.3.6.1.4.1.9.10.104.1.1.3.1.13- Type
- column
- Access
- readwrite
- Status
- current
- Units
- dB
- Parent
- cmedxProfileEntry
- Table
- cmedxProfileTable
- Siblings
- 26
Syntax
dB Integer32
Values & Constraints
Object Constraints
range: -6-14
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| cmedxProfileIndex This object uniquely identifies the H.248 profile. | column | CISCO-MEDIA-GATEWAY-MIBCCallControlProfileIndex | .1.3.6.1.4.1.9.10.104.1.1.3.1.1 |
| cmedxProfileDetectLongDigitDur This object specifies the duration for detecting a
long digit tone signal. | column | milliseconds Unsigned32 | .1.3.6.1.4.1.9.10.104.1.1.3.1.10 |
| cmedxProfileEchoCancelEnabled This object specifies whether or not the Echo
Cancellation is enabled or not. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.10.104.1.1.3.1.11 |
| cmedxProfileEchoCancelTail This object specifies the Echo Canceler coverage.
This object is valid if the cmedxProfileEchoCancelEnabled
object is 'true'.
echoCanceller8ms - 8 ms echo canceler coverage.
ech… | column | Enumeration | .1.3.6.1.4.1.9.10.104.1.1.3.1.12 |
| cmedxProfileOutAttnControl This object contains the amount of attenuation inserted
at the transmit side of the interface.
The output attenuation settings only define a loss
relative to the 0 dB setting.
The… | column | dB Unsigned32 | .1.3.6.1.4.1.9.10.104.1.1.3.1.14 |
| cmedxProfileVoIpVadEnabled This object specifies VAD (Voice Activity Detection)
is enabled for the compression DSPs of this interface
when the application is VoIP. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.10.104.1.1.3.1.15 |
| cmedxProfileVoIpVadTimer This object specifies the hangover time for VAD in the
VoIP application.
Once the voice inactivity is detected, the media gateway
waits for the duration of this value before activ… | column | milliseconds Unsigned32 | .1.3.6.1.4.1.9.10.104.1.1.3.1.16 |
| cmedxProfileVoAal2VadTimer This object specifies the hangover time for VAD in the
VoATM over AAL2 application.
Once the voice inactivity is detected, the media gateway
waits for the duration of this value b… | column | milliseconds Unsigned32 | .1.3.6.1.4.1.9.10.104.1.1.3.1.17 |
| cmedxProfileAtmBearerType This object specifies ATM bearer type.
bearerSvc (1) - the ATM bearer type is SVC (Switched
Virtual Circuit).
bearerPvc (1) - the ATM bearer type is PVC (Permanent… | column | Enumeration | .1.3.6.1.4.1.9.10.104.1.1.3.1.18 |
| cmedxProfileAtmAalPartialFill This object specifies the fill level of cells in case of
AAL adaptation .
The value of this object will be used if the MGC does
not specify partial fill in the commands.
ATM cell … | column | Unsigned32 | .1.3.6.1.4.1.9.10.104.1.1.3.1.19 |
| cmedxProfilePlayCpToneInterDur This object specifies the duration for playing
a list of call progressing tones between two call
progressing signals.
The value of 0 indicates there is no wait between
two call … | column | milliseconds Unsigned32 | .1.3.6.1.4.1.9.10.104.1.1.3.1.2 |
| cmedxProfileAtmAalType This object specifies the adaptation layer of ATM.
other (1) - None of the types listed below.
aal1 (2) - ATM AAL1 adaptation layer
aal1Sdt (3) - ATM AAL1 with SDT (Structure… | column | Enumeration | .1.3.6.1.4.1.9.10.104.1.1.3.1.20 |
| cmedxProfileSuppressBearerDigit This object controls if the digits should be suppressed
from voice media stream. When MGC has requested digits,
if this object is set to 'true', the digits will be
reported to MG… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.10.104.1.1.3.1.21 |
| cmedxProfileRowStatus When an entry is created, at least one of the objects
in the entry has to be provided and the default value
will be assigned to the rest of the objects. | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.9.10.104.1.1.3.1.22 |
| cmedxProfileOriginatingCotTx This object specifies the COT tone to be transmitted
from originating gateway in the continuity test. | column | CMedxCotTones | .1.3.6.1.4.1.9.10.104.1.1.3.1.23 |
| cmedxProfileOriginatingCotRx This object specifies the COT tone to be received
in originating gateway in the continuity test. | column | CMedxCotTones | .1.3.6.1.4.1.9.10.104.1.1.3.1.24 |
| cmedxProfileTerminatingCotTx This object specifies the COT tone to be transmitted
from terminating gateway in the continuity test. | column | CMedxCotTones | .1.3.6.1.4.1.9.10.104.1.1.3.1.25 |
| cmedxProfileTerminatingCotRx This object specifies the COT tone to be received
in terminating gateway in the continuity test. | column | CMedxCotTones | .1.3.6.1.4.1.9.10.104.1.1.3.1.26 |
| cmedxProfileComfortNoiseGenerate This object specifies the type of comfort noise generation:
(1) none: No comfort noise generation applied
(2) simple: Cisco Proprietary comfort noise generation
(3)… | column | Enumeration | .1.3.6.1.4.1.9.10.104.1.1.3.1.27 |
| cmedxProfileDtmfDigitOnDur This object specifies the duration of the active DTMF
digit during DTMF playout from the gateway.
A complete DTMF digit is characterized by DTMF on
with duration specified by th… | column | milliseconds Unsigned32 | .1.3.6.1.4.1.9.10.104.1.1.3.1.3 |
| cmedxProfileDtmfPauseDur This object specifies the duration of the pause after an
active DTMF digit during DTMF playout from the gateway.
For playout of multiple DTMF digits, the sum of the
digit-on and… | column | milliseconds Unsigned32 | .1.3.6.1.4.1.9.10.104.1.1.3.1.4 |
| cmedxProfileCot1Frequency This object specifies the tone frequency to be
transmit between gateways in the continuity test. | column | Hz Unsigned32 | .1.3.6.1.4.1.9.10.104.1.1.3.1.5 |
| cmedxProfileCot2Frequency This object specifies the tone frequency to be
received between gateways in the continuity test. | column | Hz Unsigned32 | .1.3.6.1.4.1.9.10.104.1.1.3.1.6 |
| cmedxProfileInitiateCotDur This object specifies the duration for the continuity
test tone to be played when the gateway initiates a COT.
The value of 0 indicates that the tone will be played
infinitely un… | column | milliseconds Unsigned32 | .1.3.6.1.4.1.9.10.104.1.1.3.1.7 |
| cmedxProfileRespCotMethod This object specifies the method for responding to COT
(Continuity Test Tone) when the gateway detects a
the continuity test signal.
loopback (1) - The gateway loops back … | column | Enumeration | .1.3.6.1.4.1.9.10.104.1.1.3.1.8 |
| cmedxProfileDetectLongCpToneDur This object specifies the duration for detecting a
long call progressing tone. | column | milliseconds Unsigned32 | .1.3.6.1.4.1.9.10.104.1.1.3.1.9 |