clrRrmParametersTpcVersion
CISCO-LWAPP-RRM-MIB ·
.1.3.6.1.4.1.9.9.615.1.1.1.1.13
Object
column
r/w
Enumeration
This object specifies the TPC(Transmission Power Control) version. versionOne(1) - TPC would be in coverage optimal mode. versionTwo(2) - TPC would be in interference optimal mode.
Context
- MIB
- CISCO-LWAPP-RRM-MIB
- OID
.1.3.6.1.4.1.9.9.615.1.1.1.1.13- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- clrRrmParametersEntry
- Table
- clrRrmParametersTable
- Siblings
- 24
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | versionOne |
2 | versionTwo |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| clrRrmParametersType This object uniquely represents the 802.11 interface
type for this entry. | column | CISCO-LWAPP-TC-MIBCLApIfType | .1.3.6.1.4.1.9.9.615.1.1.1.1.1 |
| clrRrmParametersDcaChannelWidth This object specifies how the system performs DCA
channel width selection
twenty - 20MHz channel width supported by this radio.
forty - 40MHz channel width supported by this … | column | Enumeration | .1.3.6.1.4.1.9.9.615.1.1.1.1.10 |
| clrRrmParametersMaxTxPower This object specifies the upper limit of transmit power in dBm.
For a 802.11a network, the system will
only accept this configuration if the
bsnGlobalDot11aDynamicTransmitPowerC… | column | dBm Integer32 | .1.3.6.1.4.1.9.9.615.1.1.1.1.11 |
| clrRrmParametersMinTxPower This object specifies the lower limit of transmit power in dBm.
For an 802.11a network, the system will
only accept this configuration if the
bsnGlobalDot11aDynamicTransmitPower… | column | dBm Integer32 | .1.3.6.1.4.1.9.9.615.1.1.1.1.12 |
| clrRrmParametersChdNoise This object specifies the state of noise
on the controller. A value of 'true'
indicates that the detection is enabled. A value
of 'false' indicates that the detection is disable… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.615.1.1.1.1.14 |
| clrRrmParametersChdInterference This object specifies the state of interference
on the controller. A value of 'true'
indicates that the detection is enabled. A value
of 'false' indicates that the detection is … | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.615.1.1.1.1.15 |
| clrRrmParametersChdLoad This object specifies the state of load
on the controller. A value of 'true'
indicates that the detection is enabled. A value
of 'false' indicates that the detection is disabled. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.615.1.1.1.1.16 |
| clrRrmParametersChdSignal This object specifies the state of signal
on the controller. A value of 'true'
indicates that the detection is enabled. A value
of 'false' indicates that the detection is disabl… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.615.1.1.1.1.17 |
| clrRrmParametersChdDevice This object specifies the state of device detection
on the controller. A value of 'true'
indicates that the detection is enabled. A value
of 'false' indicates that the detection… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.615.1.1.1.1.18 |
| clrRrmParametersMaxClients This object specifies the maximum allowed clients per radio. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.9.615.1.1.1.1.19 |
| clrRrmParametersPicoCellMode deprecated This object specifies the 802.11 pico-cell mode.
disable - pico-cell mode is disabled.
picoCellv1 - legacy pico-cell mode is in use.
picoCellv2 - in this mode the APs to use th… | column | Enumeration | .1.3.6.1.4.1.9.9.615.1.1.1.1.2 |
| clrRrmParametersRssiCheckEnable This object specifies the state of RSSI low
check on the controller. A value of 'true'
indicates that the check is enabled. A value
of 'false' indicates that the check is disabl… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.615.1.1.1.1.20 |
| clrRrmParametersRssiThreshold This object specifies the RSSI threshold value for
RSSI low check. | column | dbm Integer32 | .1.3.6.1.4.1.9.9.615.1.1.1.1.21 |
| clrRrmParametersOptRoamEnable This object specifies the state of optimized
roaming feature on the controller. A value of 'true'
indicates that the feature is enabled. A value
of 'false' indicates that the fe… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.615.1.1.1.1.22 |
| clrRrmParametersOptRoamDataRate This object specifies the data rate threshold value for
optimized roaming. A valid data rate in mbps must be entered. | column | mbps Integer32 | .1.3.6.1.4.1.9.9.615.1.1.1.1.23 |
| clrRrmParametersOptRoamInterval This object specifies the reporting interval value for
Optimized Roaming. | column | seconds Integer32 | .1.3.6.1.4.1.9.9.615.1.1.1.1.24 |
| clrRrmParametersClientNetworkPreference This object represents the client network preference.
connectivity - RRM Algorithm has a prefereance on connectiviry of the clients
throughput - RRM Algorithm has a preference… | column | Enumeration | .1.3.6.1.4.1.9.9.615.1.1.1.1.25 |
| clrRrmParametersChdEnable This object specifies the state of CHD (Coverage
Hole Detection) on the controller. A value of 'true'
indicates that the detection is enabled. A value
of 'false' indicates that … | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.615.1.1.1.1.3 |
| clrRrmParametersVoicePktCountThreshold This object specifies the minimum threshold on the
Voice packet count required to trigger the CHD
algorithm on the controller. | column | packets Unsigned32 | .1.3.6.1.4.1.9.9.615.1.1.1.1.4 |
| clrRrmParametersVoicePktPercentThreshold This object specifies the threshold on the percent
of Voice packets dropped, that is required to
trigger the CHD algorithm on the controller. | column | percent Unsigned32 | .1.3.6.1.4.1.9.9.615.1.1.1.1.5 |
| clrRrmParametersVoiceRssiThreshold This object specifies the RSSI threshold value for
Voice packets, that is required to trigger the CHD
algorithm on the controller. | column | dbm Integer32 | .1.3.6.1.4.1.9.9.615.1.1.1.1.6 |
| clrRrmParametersDataPktCountThreshold This object specifies the minimum threshold on the
Data packet count required to trigger the CHD
algorithm on the controller. | column | packets Unsigned32 | .1.3.6.1.4.1.9.9.615.1.1.1.1.7 |
| clrRrmParametersDataPktPercentThreshold This object specifies the threshold on the percent
of Data packets dropped, that is required to
trigger the CHD algorithm on the controller. | column | percent Unsigned32 | .1.3.6.1.4.1.9.9.615.1.1.1.1.8 |
| clrRrmParametersDataRssiThreshold This object specifies the RSSI threshold value for
Data packets, that is required to trigger the CHD
algorithm on the controller. | column | dbm Integer32 | .1.3.6.1.4.1.9.9.615.1.1.1.1.9 |