clrRrmParametersMaxTxPower
CISCO-LWAPP-RRM-MIB ·
.1.3.6.1.4.1.9.9.615.1.1.1.1.11
Object
column
r/w
dBm Integer32
This object specifies the upper limit of transmit power in dBm. For a 802.11a network, the system will only accept this configuration if the bsnGlobalDot11aDynamicTransmitPowerControl is set to 'automatic' or 'runOnce'. For a 802.11b network, the system will only accept this configuration if the bsnGlobalDot11bDynamicTransmitPowerControl is set to 'automatic' or 'runOnce'. The value of this attribute has to be greater than equal to value of clrRrmParametersMinTxPower.
Context
- MIB
- CISCO-LWAPP-RRM-MIB
- OID
.1.3.6.1.4.1.9.9.615.1.1.1.1.11- Type
- column
- Access
- readwrite
- Status
- current
- Units
- dBm
- Parent
- clrRrmParametersEntry
- Table
- clrRrmParametersTable
- Siblings
- 24
Syntax
dBm Integer32
Values & Constraints
Object Constraints
range: -10-30
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| clrRrmParametersType This object uniquely represents the 802.11 interface
type for this entry. | column | CISCO-LWAPP-TC-MIBCLApIfType | .1.3.6.1.4.1.9.9.615.1.1.1.1.1 |
| clrRrmParametersDcaChannelWidth This object specifies how the system performs DCA
channel width selection
twenty - 20MHz channel width supported by this radio.
forty - 40MHz channel width supported by this … | column | Enumeration | .1.3.6.1.4.1.9.9.615.1.1.1.1.10 |
| clrRrmParametersMinTxPower This object specifies the lower limit of transmit power in dBm.
For an 802.11a network, the system will
only accept this configuration if the
bsnGlobalDot11aDynamicTransmitPower… | column | dBm Integer32 | .1.3.6.1.4.1.9.9.615.1.1.1.1.12 |
| clrRrmParametersTpcVersion This object specifies the TPC(Transmission Power Control) version.
versionOne(1) - TPC would be in coverage optimal mode.
versionTwo(2) - TPC would be in interference optimal mode. | column | Enumeration | .1.3.6.1.4.1.9.9.615.1.1.1.1.13 |
| clrRrmParametersChdNoise This object specifies the state of noise
on the controller. A value of 'true'
indicates that the detection is enabled. A value
of 'false' indicates that the detection is disable… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.615.1.1.1.1.14 |
| clrRrmParametersChdInterference This object specifies the state of interference
on the controller. A value of 'true'
indicates that the detection is enabled. A value
of 'false' indicates that the detection is … | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.615.1.1.1.1.15 |
| clrRrmParametersChdLoad This object specifies the state of load
on the controller. A value of 'true'
indicates that the detection is enabled. A value
of 'false' indicates that the detection is disabled. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.615.1.1.1.1.16 |
| clrRrmParametersChdSignal This object specifies the state of signal
on the controller. A value of 'true'
indicates that the detection is enabled. A value
of 'false' indicates that the detection is disabl… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.615.1.1.1.1.17 |
| clrRrmParametersChdDevice This object specifies the state of device detection
on the controller. A value of 'true'
indicates that the detection is enabled. A value
of 'false' indicates that the detection… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.615.1.1.1.1.18 |
| clrRrmParametersMaxClients This object specifies the maximum allowed clients per radio. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.9.615.1.1.1.1.19 |
| clrRrmParametersPicoCellMode deprecated This object specifies the 802.11 pico-cell mode.
disable - pico-cell mode is disabled.
picoCellv1 - legacy pico-cell mode is in use.
picoCellv2 - in this mode the APs to use th… | column | Enumeration | .1.3.6.1.4.1.9.9.615.1.1.1.1.2 |
| clrRrmParametersRssiCheckEnable This object specifies the state of RSSI low
check on the controller. A value of 'true'
indicates that the check is enabled. A value
of 'false' indicates that the check is disabl… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.615.1.1.1.1.20 |
| clrRrmParametersRssiThreshold This object specifies the RSSI threshold value for
RSSI low check. | column | dbm Integer32 | .1.3.6.1.4.1.9.9.615.1.1.1.1.21 |
| clrRrmParametersOptRoamEnable This object specifies the state of optimized
roaming feature on the controller. A value of 'true'
indicates that the feature is enabled. A value
of 'false' indicates that the fe… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.615.1.1.1.1.22 |
| clrRrmParametersOptRoamDataRate This object specifies the data rate threshold value for
optimized roaming. A valid data rate in mbps must be entered. | column | mbps Integer32 | .1.3.6.1.4.1.9.9.615.1.1.1.1.23 |
| clrRrmParametersOptRoamInterval This object specifies the reporting interval value for
Optimized Roaming. | column | seconds Integer32 | .1.3.6.1.4.1.9.9.615.1.1.1.1.24 |
| clrRrmParametersClientNetworkPreference This object represents the client network preference.
connectivity - RRM Algorithm has a prefereance on connectiviry of the clients
throughput - RRM Algorithm has a preference… | column | Enumeration | .1.3.6.1.4.1.9.9.615.1.1.1.1.25 |
| clrRrmParametersChdEnable This object specifies the state of CHD (Coverage
Hole Detection) on the controller. A value of 'true'
indicates that the detection is enabled. A value
of 'false' indicates that … | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.615.1.1.1.1.3 |
| clrRrmParametersVoicePktCountThreshold This object specifies the minimum threshold on the
Voice packet count required to trigger the CHD
algorithm on the controller. | column | packets Unsigned32 | .1.3.6.1.4.1.9.9.615.1.1.1.1.4 |
| clrRrmParametersVoicePktPercentThreshold This object specifies the threshold on the percent
of Voice packets dropped, that is required to
trigger the CHD algorithm on the controller. | column | percent Unsigned32 | .1.3.6.1.4.1.9.9.615.1.1.1.1.5 |
| clrRrmParametersVoiceRssiThreshold This object specifies the RSSI threshold value for
Voice packets, that is required to trigger the CHD
algorithm on the controller. | column | dbm Integer32 | .1.3.6.1.4.1.9.9.615.1.1.1.1.6 |
| clrRrmParametersDataPktCountThreshold This object specifies the minimum threshold on the
Data packet count required to trigger the CHD
algorithm on the controller. | column | packets Unsigned32 | .1.3.6.1.4.1.9.9.615.1.1.1.1.7 |
| clrRrmParametersDataPktPercentThreshold This object specifies the threshold on the percent
of Data packets dropped, that is required to
trigger the CHD algorithm on the controller. | column | percent Unsigned32 | .1.3.6.1.4.1.9.9.615.1.1.1.1.8 |
| clrRrmParametersDataRssiThreshold This object specifies the RSSI threshold value for
Data packets, that is required to trigger the CHD
algorithm on the controller. | column | dbm Integer32 | .1.3.6.1.4.1.9.9.615.1.1.1.1.9 |