cgprsCgChargingSrcInterface
CISCO-GPRS-CHARGING-MIB ·
.1.3.6.1.4.1.9.9.192.1.1.58
Object
scalar
r/w
Integer32
This object specifies the loopback interface to be used by GGSN as the charging source interface. When this is set to any value other than -1, the GTP path to the charging gateways will be re-created with the new address obtained from the loopback interface and this address will be used for all the charging messages in GGSN. When this is set to -1, the global GTP virtual template will be used as source interface for all charging messages.
Context
- MIB
- CISCO-GPRS-CHARGING-MIB
- OID
.1.3.6.1.4.1.9.9.192.1.1.58- Type
- scalar
- Access
- readwrite
- Status
- current
- Parent
- ciscoGprsChargingConfig
- Siblings
- 62
Syntax
Integer32
Values & Constraints
Object Constraints
range: -1-2147483647
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| cgprsCgEnable This object is used to enable/disable the charging
transaction feature on the GGSN. When the object is
set to 'true', charging processing is enabled on the GGSN. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.192.1.1.1 |
| cgprsCgPathRequest The time interval between two TCP connection establishment
retry attempts if the TCP connection can't be established
for the communication with CG. | scalar | minutes Unsigned32 | .1.3.6.1.4.1.9.9.192.1.1.10 |
| cgprsCgContainerVolThresh The traffic volume threshold that triggers addition of a
container and closing the G-CDR. | scalar | bytes Unsigned32 | .1.3.6.1.4.1.9.9.192.1.1.11 |
| cgprsCgMapDataTos Specifies a IP Type of Service (TOS) mapping for GPRS
charging data packets transmitted by the GGSN. A higher
TOS mapping value indicates a higher service priority.
The values '6… | scalar | Unsigned32 | .1.3.6.1.4.1.9.9.192.1.1.12 |
| cgprsCgPathProtocol Specifies the transport protocol used by the GGSN to transmit
and receive charging data to and from a CG.
udp - use UDP for charging data transfers.
tcp - use TCP for ch… | scalar | Enumeration | .1.3.6.1.4.1.9.9.192.1.1.13 |
| cgprsCgServerSwitchTimeout A timeout value that determines when the GGSN attempts to
switch over to an alternate CG after a destination CG cannot
be located or becomes unusable. Setting value 0 disables th… | scalar | seconds Unsigned32 | .1.3.6.1.4.1.9.9.192.1.1.14 |
| cgprsCgConditionLimit The maximum number of charging condition changes to
trigger closure of a G-CDR partial record. When the
maximum number is reached, the G-CDR is closed and
a new partial G-CDR … | scalar | Unsigned32 | .1.3.6.1.4.1.9.9.192.1.1.15 |
| cgprsCgGtpPrimePort The destination port for transferring G-CDR between GGSN
and CG. The port number is used for both UDP and TCP. | scalar | Unsigned32 | .1.3.6.1.4.1.9.9.192.1.1.16 |
| cgprsCgN3BufferSize The transmit buffer size for sending GTP' PDU. | scalar | bytes Unsigned32 | .1.3.6.1.4.1.9.9.192.1.1.17 |
| cgprsCgChargeForRoamersOnly This object is used to indicate to the GGSN that it needs to
generate CDRs only for roamers. When the object is set
to 'false' GGSN will generate CDRs for non-roamers also.
This o… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.192.1.1.18 |
| cgprsCgTariffTimeMaxEntries Indicates the upper limit on the number of entries that the
cgprsCgTariffTimeTable may contain. | scalar | Unsigned32 | .1.3.6.1.4.1.9.9.192.1.1.19 |
| cgprsCgCdrLocalSeqNumEnable This object is used to enable/disable the feature of using
the local record sequence number field in G-CDRs on the GGSN.
When the object is set to 'true', the G-CDRs contain the … | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.192.1.1.2 |
| cgprsCgTariffTimeNextIndex This object contains an appropriate value to
be used for cgprsCgTariffTimeIndex when creating
entries in the cgprsCgTariffTimeTable. The value 0
indicates that no new rows can b… | scalar | SNMPv2-TCTestAndIncr | .1.3.6.1.4.1.9.9.192.1.1.20 |
| cgprsCgTariffTimeTable The tariff time table. The tariff time table contains all
currently configured tariff times on the GGSN | table | - | .1.3.6.1.4.1.9.9.192.1.1.21 |
| cgprsCgGatewayTable deprecated Charging gateway table.
The table contains a list of charging gateways.
A charging gateway contains databases to store the
collected G-CDRs for billing purposes.
cgprsCgGatewayTa… | table | - | .1.3.6.1.4.1.9.9.192.1.1.22 |
| cgprsCgClearCdrPartialCdr This object is used to close all existing CDRs, transfer them
to the CG and open new partial CDRs for any existing PDP
contexts.
closeCdr - close all existing CDRs.
canClos… | scalar | Enumeration | .1.3.6.1.4.1.9.9.192.1.1.23 |
| cgprsCgSgsnChangeLimit deprecated This object denotes the maximum number of SGSN changes that
will trigger the closure of G-CDR or partial record. When the
maximum number is reached, the record is closed and a ne… | scalar | Unsigned32 | .1.3.6.1.4.1.9.9.192.1.1.24 |
| cgprsCgCdrSgsnChangeLimit This object denotes the maximum number of SGSN changes that
will trigger the closure of G-CDR or partial record. When the
maximum number is reached, the record is closed and a new… | scalar | Integer32 | .1.3.6.1.4.1.9.9.192.1.1.25 |
| cgprsCgRelease This object specifies the release specific parameters that
needs to be used when communicating with the CG. for eg:
Qos Profile Info, Charging Characteristics field, etc.,
… | scalar | Enumeration | .1.3.6.1.4.1.9.9.192.1.1.26 |
| cgprsCgGtpShortHeaderEnable This object enables the GGSN to use the 6-byte GTP short
header for charging transactions. This object cannot be
toggled when there are pending CDR's. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.192.1.1.27 |
| cgprsCgTransFormNumRespEnable When this object is set to 'true', the data record transfer
response IE uses the one octet format which contains the
number of records responded. When set to 'false', it uses the… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.192.1.1.28 |
| cgprsCgContainerTimeLimit A G-CDR is used to collect charging information related
to the packet data information for a GPRS mobile in the
GGSN.The List of Traffic Data Volumes attribute of the
G-CDR consis… | scalar | seconds Unsigned32 | .1.3.6.1.4.1.9.9.192.1.1.29 |
| cgprsCgCdrNodeIdEnable This object is used to enable/disable the feature of using
the NodeID field in G-CDRs on the GGSN. When the object is
set to 'true', the G-CDRs include the NodeID field. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.192.1.1.3 |
| cgprsCgProfileTable Charging characteristics is a parameter introduced in
Release 99.Charging Characteristics allows the operator
to apply different charging methods on a per PDP basis.
C… | table | - | .1.3.6.1.4.1.9.9.192.1.1.30 |
| cgprsCgProfileMapTable This table maintains the default charging profile
mappings. The profile set in cgprsCgProfileTable will
be mapped to the default profile table. Only one
mapping to the type of MS … | table | - | .1.3.6.1.4.1.9.9.192.1.1.31 |
| cgprsCgChargingCharReject This object defines whether the incoming PDP create
request has to be rejected or accepted depending on
the charging profile match.
If in case a PDP create request come… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.192.1.1.32 |
| cgprsCgServiceMode deprecated This object specifies the service mode for charging. The
charging functions in the GGSN involve mainly
collection/accumulation of CDRs and transmitting CDRs to the
Charging Gatew… | scalar | Enumeration | .1.3.6.1.4.1.9.9.192.1.1.33 |
| cgprsCgPartialCdrGenEnable A Primary CDR refers to the first CDR for a PDP. Subsequent
CDR's, called secondary CDR's, will be opened when the primary
CDR is closed by triggers like exceeding data volume lim… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.192.1.1.34 |
| cgprsCgSwitchOverPriority deprecated This object is used to enable the switch over priority
mechanism.
'true' - If a higher priority CG comes up, it becomes the
active CG.
'false' -… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.192.1.1.35 |
| cgprsCgCharSelectionMode This object is used to add the charging characteristic
selection mode in the CDR.
'true' - Charging characteristic selection mode will be
added in the CDR.
… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.192.1.1.36 |
| cgprsCgReconnect This object enables the charging reconnect feature.
This feature when enabled, reconnects to the CG that is
unreachable due to some transient network or link failures.… | scalar | minutes Integer32 | .1.3.6.1.4.1.9.9.192.1.1.37 |
| cgprsCgPtcEnable When this object is set, GGSN sends the Packet Transfer
Command (PTC) IE in the CDR message.
'true' - send PTC IE with the CDR. The value in the
IE will be '… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.192.1.1.38 |
| cgprsCgPtcPossiblyDupEnable This object is used to send possibly duplicated Data Record
Packet. When the CDR packet is directed to a secondary CGF
(by a CDR generating node) because the currently used CGF
… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.192.1.1.39 |
| cgprsCgFlowControlEcho This object is used to enable/disable flow control
between the GGSN and CG.
When the object is set to 'true', the GGSN enables private
extension information element in the echo … | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.192.1.1.4 |
| cgprsCgCdrOptionServiceRecord G-CDRs contain information for part, or the entire
duration, of a PDP context. The G-CDR includes information
such as the subscriber (MSISDN, IMSI), APN used, QoS
applied, SGSN … | scalar | Unsigned32 | .1.3.6.1.4.1.9.9.192.1.1.40 |
| cgprsCgPartialCdrGenEnableAll This object when set to 'true' enables the GGSN to copy
the SGSN list for charging release prior to release 4
(cgprsCgRelease). The SGSN change limit trigger
specified in the ob… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.192.1.1.41 |
| cgprsCgCdrOptionApn This object when set to 'true' includes real APN in the
G-CDR and accounting records.
If object is set to 'false'- Access Point Name is
disabled in G-CDRs. The option … | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.192.1.1.42 |
| cgprsCgCdrOptionVirtualApn This object when set to 'true' includes virtual APN in
G-CDR and accounting records.
If this object is set to 'false'- Real APN is included in the
G-CDRs. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.192.1.1.43 |
| cgprsCgCdrOptionApnSelMode This object when set to 'true' includes 'APN selection mode'
field in G-CDR and sent to CG.
The field 'APN selection mode' indicates how the SGSN selected
the APN to b… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.192.1.1.44 |
| cgprsCgCdrOptionDynamicAddr This object when set to 'true' includes 'Dynamic Address'
field in G-CDR and sent to CG.
This field indicates that PDP address has been dynamically
allocated for that … | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.192.1.1.45 |
| cgprsCgCdrOptionNip This object when set to 'true' includes NIP (Network
Initiated PDP context) field in G-CDR and sent to CG.
This field indicates that PDP context is network initiated.
T… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.192.1.1.46 |
| cgprsCgCdrOptionPdpAddress This object when set to 'true' includes 'Served PDP Address'
field in G-CDR and sent to CG.
This field (Served PDP Address) contains the PDP address
of the served IMS… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.192.1.1.47 |
| cgprsCgCdrOptionPdpType This object if set to 'true' includes 'PDP Type' field
in G-CDRs.
This field defines the PDP type,e.g.IP,PPP or IHOSS:OSP. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.192.1.1.48 |
| cgprsCgCdrOptionSerMsisdn This object when set to 'true' enable the GGSN to provide
the MSISDN number from the create PDP context request
in the G-CDRs.
This field contains the Mobile Station (M… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.192.1.1.49 |
| cgprsCgCdrPktsStatEnable This object is used to enable/disable G-CDR packet statistics
collection. When the object is set to 'true', the G-CDR is
enabled to collect the packet statistics from
cgprsGtpC… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.192.1.1.5 |
| cgprsCgCdrOptionSgsnPlmn This object whe set to 'true' includes SGSN PLMN ID
(MCC and MNC) in the G-CDR and sent to CG.
The SGSN PLMN ID field contains a SGSN PLMN Identifier,
for the SGSNs w… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.192.1.1.50 |
| cgprsCgCdrOptionCamelCharInfo This object if set to 'true', S-CDR CAMEL information
recieved from SGSN, which is a copy of Tag and Length
from SGSN's CDR (S-CDR) is included in G-CDR.
If this obje… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.192.1.1.51 |
| cgprsCgCdrOptionImeisv This object when set to 'true' the IMEI (Software Version)
IE shall be handled by GGSN in a transparent manner and shall
be sent to the Charging gateway that is release 5.0 compl… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.192.1.1.52 |
| cgprsCgCdrOptionMsTimeZone This object when set to 'true' includes MS Time Zone field
in the G-CDRs and sent to CG.
MS Time Zone indicates the offset between universal time
and local time in step… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.192.1.1.53 |
| cgprsCgCdrOptionRatType This object when set to 'true' includes Radio Access Type
(RAT) IE in the G-CDRs and sent to CG.
RAT, indicates whether the SGSN serves the User Equipment
(UE) by Unive… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.192.1.1.54 |
| cgprsCgCdrOptionUserLocInfo This object when set to 'true' includes the User Location
Information IE in G-CDRs and sent to CG.
User Location Information gives Cell Global Identity
(CGI)/Service Ar… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.192.1.1.55 |
| cgprsCgServiceRecordIncludeRat This object when set to 'true', writes the RAT value into
into the service record when RAT change is recieved.
If this object is set to 'false', it disables the RAT tri… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.192.1.1.56 |
| cgprsCgServiceRecordIncludePlmn This object when set to 'true', writes the PLMN-ID of the
PDP into the service record when there is change in the
PLMN-ID.
If this object is set to 'false', it disables… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.192.1.1.57 |
| cgprsCgServiceRecordIncludeUserLocInfo When this object is set to 'true', the user location
information of the PDP is written into the service record
when there is change in the user location information.
Wh… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.192.1.1.59 |
| cgprsCgCdrNonPrimaryEnable obsolete This object controls the generation of non-primary
partial CDRs on GGSN as follows:
'true(1)' - the generation of non-primary partial CDRs
is enabled.
'false(2)'- … | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.192.1.1.6 |
| cgprsCgGroupTable Charging gateway group table.
The table contains a list of charging groups.
In each charging group, a unique primary, secondary, and
tertiary charging gateway, and iSCSI target ca… | table | - | .1.3.6.1.4.1.9.9.192.1.1.60 |
| cgprsCgGatewayIpTable Charging gateway table.
The table contains a list of charging gateways.
A charging gateway contains databases to store the
collected G-CDRs for billing purposes. | table | - | .1.3.6.1.4.1.9.9.192.1.1.61 |
| cgprsCgProfileContentDccaProfileTable This table contains the list of DCCA Profiles
configured as part of the charging profile. | table | - | .1.3.6.1.4.1.9.9.192.1.1.62 |
| cgprsCgScdrEnable This object specifies whether the SGW CDR
generation is enabled or disabled, for the sessions
in SPGW mode.
When set to 'true' SGW mode CDR generation is enabled.
when set to 'fal… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.192.1.1.63 |
| cgprsCgCdrAggreLimit The Maximum number of G-CDRs that can be aggregated in a
charging data transfer message to a CG. | scalar | CDRs Unsigned32 | .1.3.6.1.4.1.9.9.192.1.1.7 |
| cgprsCgTransInterval Specifies the time interval between transfers of
GPRS charging data for a PDP context (user session)
between the GGSN and the charging gateway. | scalar | seconds Unsigned32 | .1.3.6.1.4.1.9.9.192.1.1.8 |
| cgprsCgPktsQSize The maximum size of the GGSN's queue of outstanding charging
data transfer requests. | scalar | PDUs Unsigned32 | .1.3.6.1.4.1.9.9.192.1.1.9 |