c2900PortIfIndex
CISCO-C2900-MIB ·
.1.3.6.1.4.1.9.9.87.1.4.1.1.25
Object
column
Integer32
The value of the instance of the ifIndex object, defined in MIB-II, for the interface corresponding to this port.
Context
- MIB
- CISCO-C2900-MIB
- OID
.1.3.6.1.4.1.9.9.87.1.4.1.1.25- Type
- column
- Access
- readonly
- Status
- current
- Parent
- c2900PortEntry
- Table
- c2900PortTable
- Siblings
- 39
Syntax
Integer32
Values & Constraints
Object Constraints
range: 1-2147483647
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| c2900PortModuleIndex An index value that uniquely identifies the module
where this port is located. The value is determined
by the chassis slot number into which the module is
plugged. | column | Integer32 | .1.3.6.1.4.1.9.9.87.1.4.1.1.1 |
| c2900PortAddrSecureMaxAddresses The maximum number of secure addresses that can
be learned on this port when it is a secure port.
This number should be always higher than
c2900PortAddrSecureCurrentAddresses | column | Integer32 | .1.3.6.1.4.1.9.9.87.1.4.1.1.10 |
| c2900PortAddrSecureCurrentAddresses The current number of statically assigned
unicast addresses on the port. | column | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.9.9.87.1.4.1.1.11 |
| c2900PortAddrSecureAddrViolations The number of times a source address was
seen on this port which duplicates a secured
address configured on another port,
plus the number of times a source address was
seen on thi… | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.9.9.87.1.4.1.1.12 |
| c2900PortNumberOfLearnedAddresses The current number of dynamically learned
addresses on the port. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.9.9.87.1.4.1.1.13 |
| c2900PortNumberOfDroppedAddresses The number of times an address could not be learned
or assigned for the port because its address table
was full at one time. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.9.9.87.1.4.1.1.14 |
| c2900PortClearAddresses Set to true(1) to delete all learned and assigned
dynamic, static and secure unicast addresses the
port currently has. Setting the object to false(2)
has no effect. This object al… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.87.1.4.1.1.15 |
| c2900PortFloodUnknownMulticasts Set to true(1) to allow forwarding to this
port frames addressed to multicast addresses
that have not been configured for the port.
Set to false(2) to filter and discard such fram… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.87.1.4.1.1.16 |
| c2900PortFloodUnknownUnicasts This object controls the forwarding of unknown
unicast frames to this port. When set to true(1),
the switch will, upon receiving a frame with an
unknown unicast destination addres… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.87.1.4.1.1.17 |
| c2900PortLinkbeatStatus This object depends on the physical layer in use
and indicates the current port linkbeat status:
if the physical link between two devices is
properly connected or not.
If the valu… | column | Enumeration | .1.3.6.1.4.1.9.9.87.1.4.1.1.18 |
| c2900PortBroadcastStormAction Indicates what action to take when the broadcast
rising threshold for a port is reached.
The default action is to forwardBroadcast(2) as usual
for all broadcast frames received fr… | column | Enumeration | .1.3.6.1.4.1.9.9.87.1.4.1.1.19 |
| c2900PortIndex An index value that uniquely identifies this port
within a module. | column | Integer32 | .1.3.6.1.4.1.9.9.87.1.4.1.1.2 |
| c2900PortBroadcastRisingThreshold The broadcast rising threshold is measured in the number
of broadcast frames received on a port in a second.
When the number of broadcast frames received per
second… | column | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.9.9.87.1.4.1.1.20 |
| c2900PortBroadcastFallingThreshold The broadcast falling threshold is measured in number of
broadcast frames received on a port in a second.
When the falling threshold is crossed and the
c2900PortBro… | column | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.9.9.87.1.4.1.1.21 |
| c2900PortStatus The port's current state as defined by application
of the Spanning Tree Protocol. This state controls
what action a port takes on reception of a frame.
If the switch has detected … | column | Enumeration | .1.3.6.1.4.1.9.9.87.1.4.1.1.22 |
| c2900PortTestResult This object indicates if the port passed power on self test or not.
If the value of this object is true(1), the port passed test.
If the value of this object is false(2), the port… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.87.1.4.1.1.23 |
| c2900PortVisualIndicator This object is used to indicate the current color of
a LED. If a LED is flashing, the value of this object will
represent the color of the LED at that instant in time.
The followi… | column | Enumeration | .1.3.6.1.4.1.9.9.87.1.4.1.1.24 |
| c2900PortAddressViolationAction Indicates what action to take when an address violation
(an address mismatch or duplication) occurs on a
secure port. The default action is to do nothing.
doNothi… | column | Enumeration | .1.3.6.1.4.1.9.9.87.1.4.1.1.26 |
| c2900PortBroadcastStormAlarm When set to true(1), the switch will generate
a broadcastStorm notification upon detecting a port is
receiving broadcast packets at a rate higher than
or equal to the threshold sp… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.87.1.4.1.1.27 |
| c2900PortMonitorDestinationPort Switch Port (c2900PortSwitchPortIndex) index value of the port
that is to be monitored by this port. A value of zero can't be
used to do set, it is used to return when this object… | column | Integer32 | .1.3.6.1.4.1.9.9.87.1.4.1.1.28 |
| c2900PortSwitchPortIndex Switch port index of a port is a value that uniquely
identifies the port within a switch. This is obtained
from the port index (c2900PortIndex) and the module
index (c2900PortModu… | column | Integer32 | .1.3.6.1.4.1.9.9.87.1.4.1.1.29 |
| c2900PortUsageApplication This object indicates how the port is to be used.
The variable usage applications are shown above.
These applications are defined such that they
are mutually exclusive. In other w… | column | Enumeration | .1.3.6.1.4.1.9.9.87.1.4.1.1.3 |
| c2900PortMonitoredPortMap Indicates which ports are actually being monitored.
The octet string contains one bit per port. Each bit
within the octet string represents one port of the device.
The ordering of… | column | OctetString | .1.3.6.1.4.1.9.9.87.1.4.1.1.30 |
| c2900PortDuplexState Set to fullduplex(1) to operate in full duplex mode, port
will allow simultaneous transmit and receive which can
double its bandwidth.
Set to halfduplex(2) to opera… | column | Enumeration | .1.3.6.1.4.1.9.9.87.1.4.1.1.31 |
| c2900PortDuplexStatus The status of duplex mode on this port.
When linkbeat is not present, halfduplex is always
reported.
When linkbeat is present, the result of full dup… | column | Enumeration | .1.3.6.1.4.1.9.9.87.1.4.1.1.32 |
| c2900PortAdminSpeed The object controls the speed of the port.
The current operational speed of the port can be
determined from ifSpeed. | column | Enumeration | .1.3.6.1.4.1.9.9.87.1.4.1.1.33 |
| c2900PortNoMonitorDestinationPort Switch Port (c2900PortSwitchPortIndex) index value of the port
that is to be removed from the monitored list. A value of zero
can't be used to do set, it is used to return when th… | column | Integer32 | .1.3.6.1.4.1.9.9.87.1.4.1.1.34 |
| c2900Portdot1dBasePort This is the dot1dBasePort associated with this port. | column | Integer32 | .1.3.6.1.4.1.9.9.87.1.4.1.1.35 |
| c2900PortSpantreeFastStart Indicates whether the port is operating in spantree
fast start mode. A port with fast start enabled is
immediately put in spanning tree forwarding state on
link up, rather than s… | column | Enumeration | .1.3.6.1.4.1.9.9.87.1.4.1.1.36 |
| c2900PortVoiceVlanId The Voice Virtual Vlan ID (VVID) to which this
port belongs to.
If the VVID is not supported on the port, this MIB
object will not be configurable and will return
4096.
… | column | Integer32 | .1.3.6.1.4.1.9.9.87.1.4.1.1.37 |
| c2900PortAddrSecureAgingTime The aging interval in minutes for each secure address
entry on a given port. Depending on the type of aging
the secure address will age out after the expiration
of the aging time… | column | minutes Integer32 | .1.3.6.1.4.1.9.9.87.1.4.1.1.38 |
| c2900PortAddrSecureAgingType If the value of this object on a given port is
absolute - all the secure addresses on this
port will age out exactly after the aging
time configured for th… | column | Enumeration | .1.3.6.1.4.1.9.9.87.1.4.1.1.39 |
| c2900PortGroupIndex This object is meaningful only when the
corresponding c2900PortUsageApplication is portGrouping.
Ports assigned with the same value of c2900PortGroupIndex
belong to the same conne… | column | Integer32 | .1.3.6.1.4.1.9.9.87.1.4.1.1.4 |
| c2900PortAddrSecureAgingStatic Set to true(1) to enable aging for statically
configured secure addresses on one port. Disable
the aging for statically configured secure
addresses if set to false(2).
… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.87.1.4.1.1.40 |
| c2900PortMayLearnAddress deprecated This object reflects an internal state of the port
with regard to its ability to learn new addresses.
Certain port configurations such as learning time
limit, security usage, etc.… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.87.1.4.1.1.5 |
| c2900PortMayForwardFrames This object reflects an internal state of the port
with regard to its ability to forward frames.
A port sometimes stops forwarding frames when it
is blocked by the Spanning Tree P… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.87.1.4.1.1.6 |
| c2900PortBufferCongestionControl deprecated Seting this object to true(1) allows the switch
to run its buffer congestion control algorithm on the
port. Setting the object to false(2) disallows
such control. The buffer cong… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.87.1.4.1.1.7 |
| c2900PortBufferCongestionThreshholdPercent The port buffer congestion threshold provides an early
warning to the switch that the port is about to
exhaust all its guaranteed buffers, leading to congestion.
This threshold is… | column | Integer32 | .1.3.6.1.4.1.9.9.87.1.4.1.1.8 |
| c2900PortFrameAge The aging interval in milliseconds after
which old frames queued for transmission on this
port are discarded. | column | milliseconds Integer32 | .1.3.6.1.4.1.9.9.87.1.4.1.1.9 |