bscPortVirtualAddress
CISCO-BSC-MIB ·
.1.3.6.1.4.1.9.9.36.1.1.1.1.13
Object
column
Integer32
This parameter is valid for contention only. It is the address to be used for this interface when the remote peer router is being used as a concentrator. The default is 01.
Context
- MIB
- CISCO-BSC-MIB
- OID
.1.3.6.1.4.1.9.9.36.1.1.1.1.13- Type
- column
- Access
- readonly
- Status
- current
- Parent
- bscPortEntry
- Table
- bscPortTable
- Siblings
- 13
Syntax
Integer32
Values & Constraints
Object Constraints
range: 1-254
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| bscPortRole The router's DLC role to the attached node.
If the bscPortRole is primary, this implies that
the port is connected to a remote secondary device.
If the role is generic, this indic… | column | Enumeration | .1.3.6.1.4.1.9.9.36.1.1.1.1.1 |
| bscPortProtocolViolations Count of protocol violations. This counter is
incremented when an unexpected BSC Data Link Control
character is received from the remote device; that
is, the control character i… | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.9.9.36.1.1.1.1.10 |
| bscPortHostTimeout This parameter is valid for interfaces configured secondary
which additionally are running local-acknowledgement. If the
configuration does not match the value will be shown as z… | column | deciseconds Integer32 | .1.3.6.1.4.1.9.9.36.1.1.1.1.11 |
| bscPortSpecPoll This parameter is valid for primary, local-acknowledgement
interfaces only. It is set to TRUE when the interface is
configured to treat specific polls as general polls.
If the c… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.36.1.1.1.1.12 |
| bscPortContentionDialTimeout This parameter is valid for dialContention only. It is
the amount of time an interface can be quiescent before
return the interface to the dial-in pool.
The default is 5 seconds. | column | seconds Integer32 | .1.3.6.1.4.1.9.9.36.1.1.1.1.14 |
| bscPortCodeSet The code set used for the line controls. | column | Enumeration | .1.3.6.1.4.1.9.9.36.1.1.1.1.2 |
| bscPortPause For primary, it is the minimum time to be taken
for a cycle round the active poll table; if this
time has not elapsed when the bottom of the poll
table is reached, then polling… | column | Integer32 | .1.3.6.1.4.1.9.9.36.1.1.1.1.3 |
| bscPortServlim This parameter is valid for primary only. It is
the number of times the active poll table will
be cycled before a non-responding control unit
will be polled. The default is 3. | column | Integer32 | .1.3.6.1.4.1.9.9.36.1.1.1.1.4 |
| bscPortPollTimeout This parameter is valid for primary only. It is
the time that the primary will wait for a response
to a poll or select. The units are tenths of a second.
The default is 10 (1 se… | column | Integer32 | .1.3.6.1.4.1.9.9.36.1.1.1.1.5 |
| bscPortRecoveryRetries This is the number of times that a recovery sequence
will be retried before the connection is considered
to have failed. The default is 5. | column | Integer32 | .1.3.6.1.4.1.9.9.36.1.1.1.1.6 |
| bscPortUnknownControlUnitsReceived Count of frames received from the serial
interface with an unsupported control unit
address. If this value is non-zero it indicates
a problem in the configuration. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.9.9.36.1.1.1.1.7 |
| bscPortSoftErrors Count of soft errors; these are errors
which have been recovered. This includes
CRC errors received, frames which were
retransmitted for any reason (NAK received
or the wrong AC… | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.9.9.36.1.1.1.1.8 |
| bscPortHardErrors Count of hard errors; these are errors which
have not been recovered after bscPortRecoveryRetries
number of retries, and therefore the connection
has been terminated.
These erro… | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.9.9.36.1.1.1.1.9 |