bscPortSpecPoll
CISCO-BSC-MIB ·
.1.3.6.1.4.1.9.9.36.1.1.1.1.12
Object
column
SNMPv2-TCTruthValue
This parameter is valid for primary, local-acknowledgement interfaces only. It is set to TRUE when the interface is configured to treat specific polls as general polls. If the configuration cannot support this value, it will be set to FALSE. The default is FALSE.
Context
- MIB
- CISCO-BSC-MIB
- OID
.1.3.6.1.4.1.9.9.36.1.1.1.1.12- Type
- column
- Access
- readonly
- Status
- current
- Parent
- bscPortEntry
- Table
- bscPortTable
- Siblings
- 13
Values & Constraints
Type Values
1 | true |
2 | false |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| bscPortRole The router's DLC role to the attached node.
If the bscPortRole is primary, this implies that
the port is connected to a remote secondary device.
If the role is generic, this indic… | column | Enumeration | .1.3.6.1.4.1.9.9.36.1.1.1.1.1 |
| bscPortProtocolViolations Count of protocol violations. This counter is
incremented when an unexpected BSC Data Link Control
character is received from the remote device; that
is, the control character i… | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.9.9.36.1.1.1.1.10 |
| bscPortHostTimeout This parameter is valid for interfaces configured secondary
which additionally are running local-acknowledgement. If the
configuration does not match the value will be shown as z… | column | deciseconds Integer32 | .1.3.6.1.4.1.9.9.36.1.1.1.1.11 |
| bscPortVirtualAddress This parameter is valid for contention only. It is
the address to be used for this interface when the
remote peer router is being used as a concentrator.
The default is 01. | column | Integer32 | .1.3.6.1.4.1.9.9.36.1.1.1.1.13 |
| bscPortContentionDialTimeout This parameter is valid for dialContention only. It is
the amount of time an interface can be quiescent before
return the interface to the dial-in pool.
The default is 5 seconds. | column | seconds Integer32 | .1.3.6.1.4.1.9.9.36.1.1.1.1.14 |
| bscPortCodeSet The code set used for the line controls. | column | Enumeration | .1.3.6.1.4.1.9.9.36.1.1.1.1.2 |
| bscPortPause For primary, it is the minimum time to be taken
for a cycle round the active poll table; if this
time has not elapsed when the bottom of the poll
table is reached, then polling… | column | Integer32 | .1.3.6.1.4.1.9.9.36.1.1.1.1.3 |
| bscPortServlim This parameter is valid for primary only. It is
the number of times the active poll table will
be cycled before a non-responding control unit
will be polled. The default is 3. | column | Integer32 | .1.3.6.1.4.1.9.9.36.1.1.1.1.4 |
| bscPortPollTimeout This parameter is valid for primary only. It is
the time that the primary will wait for a response
to a poll or select. The units are tenths of a second.
The default is 10 (1 se… | column | Integer32 | .1.3.6.1.4.1.9.9.36.1.1.1.1.5 |
| bscPortRecoveryRetries This is the number of times that a recovery sequence
will be retried before the connection is considered
to have failed. The default is 5. | column | Integer32 | .1.3.6.1.4.1.9.9.36.1.1.1.1.6 |
| bscPortUnknownControlUnitsReceived Count of frames received from the serial
interface with an unsupported control unit
address. If this value is non-zero it indicates
a problem in the configuration. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.9.9.36.1.1.1.1.7 |
| bscPortSoftErrors Count of soft errors; these are errors
which have been recovered. This includes
CRC errors received, frames which were
retransmitted for any reason (NAK received
or the wrong AC… | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.9.9.36.1.1.1.1.8 |
| bscPortHardErrors Count of hard errors; these are errors which
have not been recovered after bscPortRecoveryRetries
number of retries, and therefore the connection
has been terminated.
These erro… | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.9.9.36.1.1.1.1.9 |