bscPortSoftErrors

CISCO-BSC-MIB · .1.3.6.1.4.1.9.9.36.1.1.1.1.8

MIB view Table view

Object

column SNMPv2-SMICounter32

Count of soft errors; these are errors 
which have been recovered.  This includes
CRC errors received, frames which were
retransmitted for any reason (NAK received
or the wrong ACK received), etc.  This count
is a measure of the quality of the port/line,
but should be considered in relation to the
amount of traffic on the port (frames
or bytes sent and received).
This count includes all control unit soft
errors on this port, plus errors which were
not for a specific control unit.

Context

MIB: CISCO-BSC-MIB
OID: .1.3.6.1.4.1.9.9.36.1.1.1.1.8
Type: column
Access: readonly
Status: current
Parent: bscPortEntry
Table: bscPortTable
Siblings: 13

Syntax

SNMPv2-SMICounter32

Source: SNMPv2-SMICounter32
Base type: Unsigned32

Values & Constraints

Type Constraints

range: 0..4294967295

Related Objects

Sibling Objects

Object	Type	Syntax	OID
bscPortRole The router's DLC role to the attached node. If the bscPortRole is primary, this implies that the port is connected to a remote secondary device. If the role is generic, this indic…	column	Enumeration	`.1.3.6.1.4.1.9.9.36.1.1.1.1.1`
bscPortProtocolViolations Count of protocol violations. This counter is incremented when an unexpected BSC Data Link Control character is received from the remote device; that is, the control character i…	column	SNMPv2-SMICounter32	`.1.3.6.1.4.1.9.9.36.1.1.1.1.10`
bscPortHostTimeout This parameter is valid for interfaces configured secondary which additionally are running local-acknowledgement. If the configuration does not match the value will be shown as z…	column	deciseconds Integer32	`.1.3.6.1.4.1.9.9.36.1.1.1.1.11`
bscPortSpecPoll This parameter is valid for primary, local-acknowledgement interfaces only. It is set to TRUE when the interface is configured to treat specific polls as general polls. If the c…	column	SNMPv2-TCTruthValue	`.1.3.6.1.4.1.9.9.36.1.1.1.1.12`
bscPortVirtualAddress This parameter is valid for contention only. It is the address to be used for this interface when the remote peer router is being used as a concentrator. The default is 01.	column	Integer32	`.1.3.6.1.4.1.9.9.36.1.1.1.1.13`
bscPortContentionDialTimeout This parameter is valid for dialContention only. It is the amount of time an interface can be quiescent before return the interface to the dial-in pool. The default is 5 seconds.	column	seconds Integer32	`.1.3.6.1.4.1.9.9.36.1.1.1.1.14`
bscPortCodeSet The code set used for the line controls.	column	Enumeration	`.1.3.6.1.4.1.9.9.36.1.1.1.1.2`
bscPortPause For primary, it is the minimum time to be taken for a cycle round the active poll table; if this time has not elapsed when the bottom of the poll table is reached, then polling…	column	Integer32	`.1.3.6.1.4.1.9.9.36.1.1.1.1.3`
bscPortServlim This parameter is valid for primary only. It is the number of times the active poll table will be cycled before a non-responding control unit will be polled. The default is 3.	column	Integer32	`.1.3.6.1.4.1.9.9.36.1.1.1.1.4`
bscPortPollTimeout This parameter is valid for primary only. It is the time that the primary will wait for a response to a poll or select. The units are tenths of a second. The default is 10 (1 se…	column	Integer32	`.1.3.6.1.4.1.9.9.36.1.1.1.1.5`
bscPortRecoveryRetries This is the number of times that a recovery sequence will be retried before the connection is considered to have failed. The default is 5.	column	Integer32	`.1.3.6.1.4.1.9.9.36.1.1.1.1.6`
bscPortUnknownControlUnitsReceived Count of frames received from the serial interface with an unsupported control unit address. If this value is non-zero it indicates a problem in the configuration.	column	SNMPv2-SMICounter32	`.1.3.6.1.4.1.9.9.36.1.1.1.1.7`
bscPortHardErrors Count of hard errors; these are errors which have not been recovered after bscPortRecoveryRetries number of retries, and therefore the connection has been terminated. These erro…	column	SNMPv2-SMICounter32	`.1.3.6.1.4.1.9.9.36.1.1.1.1.9`