bscPortPause

CISCO-BSC-MIB · .1.3.6.1.4.1.9.9.36.1.1.1.1.3

MIB view Table view

Object

column Integer32

For primary, it is the minimum time to be taken 
for a cycle round the active poll table; if this 
time has not elapsed when the bottom of the poll 
table is reached, then polling will pause until 
this timer expires. A value of zero means there 
will be no pause between cycles round the poll 
table. 
For secondary, the pause time out is the delay 
taken before sending a response to a poll 
when it has no data frame to send.
The units are tenths of a second.  The default
is 10 (1 second).

Context

MIB: CISCO-BSC-MIB
OID: .1.3.6.1.4.1.9.9.36.1.1.1.1.3
Type: column
Access: readonly
Status: current
Parent: bscPortEntry
Table: bscPortTable
Siblings: 13

Syntax

Integer32

Values & Constraints

Object Constraints

range: 0-255

Related Objects

Sibling Objects

Object	Type	Syntax	OID
bscPortRole The router's DLC role to the attached node. If the bscPortRole is primary, this implies that the port is connected to a remote secondary device. If the role is generic, this indic…	column	Enumeration	`.1.3.6.1.4.1.9.9.36.1.1.1.1.1`
bscPortProtocolViolations Count of protocol violations. This counter is incremented when an unexpected BSC Data Link Control character is received from the remote device; that is, the control character i…	column	SNMPv2-SMICounter32	`.1.3.6.1.4.1.9.9.36.1.1.1.1.10`
bscPortHostTimeout This parameter is valid for interfaces configured secondary which additionally are running local-acknowledgement. If the configuration does not match the value will be shown as z…	column	deciseconds Integer32	`.1.3.6.1.4.1.9.9.36.1.1.1.1.11`
bscPortSpecPoll This parameter is valid for primary, local-acknowledgement interfaces only. It is set to TRUE when the interface is configured to treat specific polls as general polls. If the c…	column	SNMPv2-TCTruthValue	`.1.3.6.1.4.1.9.9.36.1.1.1.1.12`
bscPortVirtualAddress This parameter is valid for contention only. It is the address to be used for this interface when the remote peer router is being used as a concentrator. The default is 01.	column	Integer32	`.1.3.6.1.4.1.9.9.36.1.1.1.1.13`
bscPortContentionDialTimeout This parameter is valid for dialContention only. It is the amount of time an interface can be quiescent before return the interface to the dial-in pool. The default is 5 seconds.	column	seconds Integer32	`.1.3.6.1.4.1.9.9.36.1.1.1.1.14`
bscPortCodeSet The code set used for the line controls.	column	Enumeration	`.1.3.6.1.4.1.9.9.36.1.1.1.1.2`
bscPortServlim This parameter is valid for primary only. It is the number of times the active poll table will be cycled before a non-responding control unit will be polled. The default is 3.	column	Integer32	`.1.3.6.1.4.1.9.9.36.1.1.1.1.4`
bscPortPollTimeout This parameter is valid for primary only. It is the time that the primary will wait for a response to a poll or select. The units are tenths of a second. The default is 10 (1 se…	column	Integer32	`.1.3.6.1.4.1.9.9.36.1.1.1.1.5`
bscPortRecoveryRetries This is the number of times that a recovery sequence will be retried before the connection is considered to have failed. The default is 5.	column	Integer32	`.1.3.6.1.4.1.9.9.36.1.1.1.1.6`
bscPortUnknownControlUnitsReceived Count of frames received from the serial interface with an unsupported control unit address. If this value is non-zero it indicates a problem in the configuration.	column	SNMPv2-SMICounter32	`.1.3.6.1.4.1.9.9.36.1.1.1.1.7`
bscPortSoftErrors Count of soft errors; these are errors which have been recovered. This includes CRC errors received, frames which were retransmitted for any reason (NAK received or the wrong AC…	column	SNMPv2-SMICounter32	`.1.3.6.1.4.1.9.9.36.1.1.1.1.8`
bscPortHardErrors Count of hard errors; these are errors which have not been recovered after bscPortRecoveryRetries number of retries, and therefore the connection has been terminated. These erro…	column	SNMPv2-SMICounter32	`.1.3.6.1.4.1.9.9.36.1.1.1.1.9`