cadpStatPathFEBErrors
CISCO-ATM-DUAL-PHY-MIB ·
.1.3.6.1.4.1.9.9.60.1.1.1.1.10
Object
column
SNMPv2-SMICounter32
The number of B3 errors in the previous frame inserted
by the transmitter. The receiver checks for this in the
G1 byte of the frame. A non-zero value (legal range is
binary 0000 - 1000) indicates a line layer error in
the remote end. Any other value is treated as no error.
Count of Path Far End Bit Errors (FEBE) on this phy.
Context
- MIB
- CISCO-ATM-DUAL-PHY-MIB
- OID
.1.3.6.1.4.1.9.9.60.1.1.1.1.10- Type
- column
- Access
- readonly
- Status
- current
- Parent
- cadpStatEntry
- Table
- cadpStatTable
- Siblings
- 9
Syntax
SNMPv2-SMICounter32
- Source
- SNMPv2-SMICounter32
- Base type
Unsigned32
Values & Constraints
Type Constraints
range: 0..4294967295
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| cadpStatLossOfSignal Set to true if the phy is currently experiencing a
loss of signal (LOS) from its connected port. Set to false
if the phy is not experiencing a loss of signal. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.60.1.1.1.1.1 |
| cadpStatCorrectableHCSErrors The Header Checksum (HCS) is a CRC-8 calculation over
the first 4 octets of the ATM cell header. The received
HCS is verified using the polynomial x^8 + x^2 + x + 1.
The coset po… | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.9.9.60.1.1.1.1.11 |
| cadpStatUncorrectableHCSErrors The Header Checksum (HCS) is a CRC-8 calculation over
the first 4 octets of the ATM cell header. The received
HCS is verified using the polynomial x^8 + x^2 + x + 1.
The coset pol… | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.9.9.60.1.1.1.1.12 |
| cadpStatFarEndReceiveFailure Set to true if the phy is currently experiencing a far
end receive failure (FERF) with its connected port. Set to
false if the phy is not experiencing a far end receive
failure. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.60.1.1.1.1.2 |
| cadpStatActive Set to true when this phy is currently the active phy.
Set to false when this phy is not the currently active phy. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.60.1.1.1.1.5 |
| cadpStatSectionBIP8Errors The Bit Interleaved Parity 8 is an error checking code
applied for quick isolation of faults. Each bit in the
B octets is set to 1 or 0 as necessary to obtain even
parity over th… | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.9.9.60.1.1.1.1.6 |
| cadpStatLineBIP824Errors The Bit Interleaved Parity 8/24 is an error checking code
based on even parity. The calculated BIP code for frame N
is compared with the BIP-8/24 code extracted from the B2
byte(… | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.9.9.60.1.1.1.1.7 |
| cadpStatLineFEBErrors The number of bits (binary 000 to 1000) in the previous
BIP-8 that didn't match the even parity check are inserted
by the transmitter. The receiver checks for this in the
M0/M1 … | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.9.9.60.1.1.1.1.8 |
| cadpStatPathBIP8Errors The Bit Interleaved Parity 8 is an error checking code
applied for quick isolation of faults. Each bit in the
B octets is set to 1 or 0 as necessary to obtain even
parity over th… | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.9.9.60.1.1.1.1.9 |