cApsConfigWaitToRestore
CISCO-APS-MIB ·
.1.3.6.1.4.1.9.10.71.1.1.2.1.9
Object
column
r/w
seconds Integer32
The Wait To Restore period in seconds.
After clearing of a condition that necessitated an
automatic switch, the wait to restore period must elapse
before reverting. This is intended to avoid rapid switch
oscillations.
GR-253-CORE specifies a Wait To Restore range of 5 to 12
minutes. G.783 defines a 5 to 12 minute Wait To Restore
range in section 5.4.1.1.3, but also allows for a shorter
WTR period in Table 2-1,
WaitToRestore value (MI_WTRtime: 0..(5)..12 minutes).
This object may not be modified if the associated
cApsConfigRowStatus object is equal to active(1).
Context
- MIB
- CISCO-APS-MIB
- OID
.1.3.6.1.4.1.9.10.71.1.1.2.1.9- Type
- column
- Access
- readwrite
- Status
- current
- Units
- seconds
- Parent
- cApsConfigEntry
- Table
- cApsConfigTable
- Siblings
- 9
Syntax
seconds Integer32
Values & Constraints
Object Constraints
range: 0-720
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| cApsConfigName A textual name for the APS group. | column | OctetString | .1.3.6.1.4.1.9.10.71.1.1.2.1.1 |
| cApsConfigCreationTime The value of sysUpTime at the time the row was
created | column | SNMPv2-TCTimeStamp | .1.3.6.1.4.1.9.10.71.1.1.2.1.10 |
| cApsConfigRowStatus The status of this APS group entry.
An entry may not exist in the active state unless all
objects in the entry have an appropriate value. Also,
all associated cAps… | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.9.10.71.1.1.2.1.2 |
| cApsConfigMode The architecture of the APS group.
onePlusOne
The 1+1 architecture permanently bridges the working
line to the protection line.
oneToN… | column | Enumeration | .1.3.6.1.4.1.9.10.71.1.1.2.1.3 |
| cApsConfigRevert The revertive mode of the APS group.
nonrevertive
Traffic remains on the protection line until another
switch request is received.
re… | column | Enumeration | .1.3.6.1.4.1.9.10.71.1.1.2.1.4 |
| cApsConfigDirection The directional mode of the APS group.
unidirectional
The unidirectional mode provides protection in one
direction.
bidirectional
… | column | Enumeration | .1.3.6.1.4.1.9.10.71.1.1.2.1.5 |
| cApsConfigExtraTraffic This object enables or disables the transfer of extra
traffic on the protection channel in a 1:n architecture.
This object must be set to disabled if the architecture
is 1+1. It … | column | Enumeration | .1.3.6.1.4.1.9.10.71.1.1.2.1.6 |
| cApsConfigSdBerThreshold The Signal Degrade Bit Error Rate.
The negated value of this number is used as the exponent
of 10 for computing the threshold value for the Bit Error
Rate (BER). Fo… | column | Integer32 | .1.3.6.1.4.1.9.10.71.1.1.2.1.7 |
| cApsConfigSfBerThreshold The Signal Failure Bit Error Rate.
The negated value of this number is used as the exponent
of 10 for computing the threshold value for the Bit Error
Rate (BER). Fo… | column | Integer32 | .1.3.6.1.4.1.9.10.71.1.1.2.1.8 |