cwsPtpModemModemTxCompensationDispersionValue
CIENA-WS-PTP-MODEM-MIB ·
.1.3.6.1.4.1.1271.3.4.9.8.1.13
Object
Tx compensation dispersion value range from -40000 ps/nm to 85000 ps/nm. Default is 0
Context
- MIB
- CIENA-WS-PTP-MODEM-MIB
- OID
.1.3.6.1.4.1.1271.3.4.9.8.1.13- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- cwsPtpModemModemEntry
- Table
- cwsPtpModemModemTable
- Siblings
- 14
Syntax
CIENA-WS-TYPEDEFS-MIBDecimal1Dig
- Source
- CIENA-WS-TYPEDEFS-MIBDecimal1Dig
- Base type
Integer32
Values & Constraints
Type Constraints
range: -2147483640..2147483640
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| cwsPtpModemModemTableSnmpKey Unique key for cwsPtpModemModem | column | Integer32 | .1.3.6.1.4.1.1271.3.4.9.8.1.1 |
| cwsPtpModemModemTxTuningMode This is the Tuning Mode, which can be set as performance-optimized (normal) or accelerated tuning mode. Default is performance-optimized | column | Enumeration | .1.3.6.1.4.1.1271.3.4.9.8.1.10 |
| cwsPtpModemModemDifferentialEncoding This parameter is used to configure which differential encoding mode to apply to the OTM signal. It can be set as None, Hard, Soft, Xd. Default is none. | column | Enumeration | .1.3.6.1.4.1.1271.3.4.9.8.1.11 |
| cwsPtpModemModemTxCompensationDispersionMode Tx Compensation Dispersion Mode. Default is Off. | column | Enumeration | .1.3.6.1.4.1.1271.3.4.9.8.1.12 |
| cwsPtpModemModemFastReceiverRecoveryState obsolete Whether fast receiver recovery state is enabled or disabled. Allows modem to attempt to reacquire a signal very soon after a loss of signal by using predefined tuning values.
This… | column | CIENA-WS-TYPEDEFS-MIBEnabledDisabledEnum | .1.3.6.1.4.1.1271.3.4.9.8.1.14 |
| cwsPtpModemModemLaserCenteringRange This parameter is used to configure the laser centering range. | column | CIENA-WS-TYPEDEFS-MIBDecimal1Dig | .1.3.6.1.4.1.1271.3.4.9.8.1.15 |
| cwsPtpModemModemChannelContentionDetectionAvoidance Turns the channel contention detection and avoidance feature on or off. This feature is used to detect the situation where the modem port turn on a wavelength (or frequency in Gri… | column | CIENA-WS-TYPEDEFS-MIBOnOffEnum | .1.3.6.1.4.1.1271.3.4.9.8.1.2 |
| cwsPtpModemModemPerformanceOptimizationMode Performance Optimization. It optimizes for either reach or latency. Default is reach. | column | Enumeration | .1.3.6.1.4.1.1271.3.4.9.8.1.3 |
| cwsPtpModemModemCarrierCenteringMode This parameter is used to configure which Carrier centering mode to apply to the OTM signal. Default is mode-2. | column | Enumeration | .1.3.6.1.4.1.1271.3.4.9.8.1.4 |
| cwsPtpModemModemInterleaverMode The Interleaver Mode. It can be set as standard or enhanced. Default is enhanced. | column | Enumeration | .1.3.6.1.4.1.1271.3.4.9.8.1.5 |
| cwsPtpModemModemRotation To enable (on) or disable (off) Jones's rotation. Default is off | column | CIENA-WS-TYPEDEFS-MIBOnOffEnum | .1.3.6.1.4.1.1271.3.4.9.8.1.6 |
| cwsPtpModemModemSpectralOccupancyMode Spectral Occupancy Mode. This is the optical channel spectral Occupancy parameter which supports two different kinds of waveforms: narrow and wide. Default is narrow. Narrow: Root… | column | Enumeration | .1.3.6.1.4.1.1271.3.4.9.8.1.7 |
| cwsPtpModemModemTxPowerReductionState This parameter is used to enable TX blanking functionality. Default is Off | column | CIENA-WS-TYPEDEFS-MIBEnabledDisabledEnum | .1.3.6.1.4.1.1271.3.4.9.8.1.8 |
| cwsPtpModemModemTxReductionMode Transmit XPM reduction. It can be set as Positive, Negative or Auto. This should always be enabled (Positive). Disabling this should be done for only interworking purposes. | column | Enumeration | .1.3.6.1.4.1.1271.3.4.9.8.1.9 |