cMsDwdmIfFECValidIntervals
CERENT-MSDWDM-MIB ·
.1.3.6.1.4.1.3607.2.40.1.1.1.9
Object
column
Unsigned32
This object gives the number of contiguous 15 minute
intervals for which valid FEC PM data is available
for the particular interface.
The value of this object will be n (where n is the maximum
number of 15 minute intervals supported at this interface),
unless the measurement was (re-)started within the last
(nx15) minutes, in which case the value will be the
number of 15 minute intervals for which the agent
has some data.
This object reports a value 0, if FEC is turned off.
Context
- MIB
- CERENT-MSDWDM-MIB
- OID
.1.3.6.1.4.1.3607.2.40.1.1.1.9- Type
- column
- Access
- readonly
- Status
- current
- Parent
- cMsDwdmIfConfigEntry
- Table
- cMsDwdmIfConfigTable
- Siblings
- 9
Syntax
Unsigned32
Values & Constraints
Object Constraints
range: 0-96
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| cMsDwdmIfConfigProtocol This object is used to specify the protocol of the data
carried over the interface.
This object applies to linecards which support a variety of
protocols and allo… | column | ProtocolType | .1.3.6.1.4.1.3607.2.40.1.1.1.1 |
| cMsDwdmIfConfigFECMode This object allows the management client to enable
gathering FEC ( Forward Error Correction ) counters on
an applicable interface, by writing a value of 'enableStandard'
or 'e… | column | Enumeration | .1.3.6.1.4.1.3607.2.40.1.1.1.10 |
| cMsDwdmIfConfigDataRate This object allows the management client to set the
data rate across the interface.
passThru denotes 2R, Reamplification and reshaping.
stm1 denotes 3R, Reamp, … | column | Enumeration | .1.3.6.1.4.1.3607.2.40.1.1.1.2 |
| cMsDwdmIfConfigLoopback This object allows the management client to configure
loopback for the client side or trunk side interfaces.
'noLoop' - No Loopback present.
'diagnosticLoo… | column | Enumeration | .1.3.6.1.4.1.3607.2.40.1.1.1.3 |
| cMsDwdmIfConfigWavelength This object allows the management client to configure
the wavelength mode of operation to the applicable interfaces. | column | OpticalWavelength | .1.3.6.1.4.1.3607.2.40.1.1.1.4 |
| cMsDwdmIfConfigOtnStatus This object allows the management client to enable
the OTN (G.709) on an applicable interface,by writing a
value of 'true' to this object. To bypass the monitoring
hardware, … | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.3607.2.40.1.1.1.5 |
| cMsDwdmIfConfigFECStatus This object allows the management client to enable
gathering FEC ( Forward Error Correction ) counters on
an applicable interface, by writing a value of 'true'
to this object.… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.3607.2.40.1.1.1.6 |
| cMsDwdmIfOpticsValidIntervals This object gives the number of contiguous 15 minute
intervals for which valid Optical Monitor PM data is available
for the particular interface.
The value of this… | column | Unsigned32 | .1.3.6.1.4.1.3607.2.40.1.1.1.7 |
| cMsDwdmIfOTNValidIntervals This object gives the number of contiguous 15 minute
intervals for which valid OTN performance monitoring data is
available for the particular interface.
The valu… | column | Unsigned32 | .1.3.6.1.4.1.3607.2.40.1.1.1.8 |