cMsDwdmIfConfigProtocol
CERENT-MSDWDM-MIB ·
.1.3.6.1.4.1.3607.2.40.1.1.1.1
Object
column
r/w
ProtocolType
This object is used to specify the protocol of the data
carried over the interface.
This object applies to linecards which support a variety of
protocols and allow dynamic configuration of the specific
protocol to be monitored on the interface. The ifType value
for such interfaces remains fixed.
Context
- MIB
- CERENT-MSDWDM-MIB
- OID
.1.3.6.1.4.1.3607.2.40.1.1.1.1- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- cMsDwdmIfConfigEntry
- Table
- cMsDwdmIfConfigTable
- Siblings
- 9
Syntax
ProtocolType
- Source
- ProtocolType
- Base type
Enumeration
Values & Constraints
Type Values
1 | other |
2 | unknown |
4 | tenGigEth |
5 | fibreChOrOneGigEth |
7 | unframed |
8 | sonet |
9 | sdh |
10 | sysplexIscCompatibility |
11 | sysplexIscPeer |
12 | sysplexTimerEtr |
13 | sysplexTimerClo |
14 | fastEthernet |
15 | fddi |
16 | eightGfc |
17 | oc768 |
18 | otn |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| cMsDwdmIfConfigFECMode This object allows the management client to enable
gathering FEC ( Forward Error Correction ) counters on
an applicable interface, by writing a value of 'enableStandard'
or 'e… | column | Enumeration | .1.3.6.1.4.1.3607.2.40.1.1.1.10 |
| cMsDwdmIfConfigDataRate This object allows the management client to set the
data rate across the interface.
passThru denotes 2R, Reamplification and reshaping.
stm1 denotes 3R, Reamp, … | column | Enumeration | .1.3.6.1.4.1.3607.2.40.1.1.1.2 |
| cMsDwdmIfConfigLoopback This object allows the management client to configure
loopback for the client side or trunk side interfaces.
'noLoop' - No Loopback present.
'diagnosticLoo… | column | Enumeration | .1.3.6.1.4.1.3607.2.40.1.1.1.3 |
| cMsDwdmIfConfigWavelength This object allows the management client to configure
the wavelength mode of operation to the applicable interfaces. | column | OpticalWavelength | .1.3.6.1.4.1.3607.2.40.1.1.1.4 |
| cMsDwdmIfConfigOtnStatus This object allows the management client to enable
the OTN (G.709) on an applicable interface,by writing a
value of 'true' to this object. To bypass the monitoring
hardware, … | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.3607.2.40.1.1.1.5 |
| cMsDwdmIfConfigFECStatus This object allows the management client to enable
gathering FEC ( Forward Error Correction ) counters on
an applicable interface, by writing a value of 'true'
to this object.… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.3607.2.40.1.1.1.6 |
| cMsDwdmIfOpticsValidIntervals This object gives the number of contiguous 15 minute
intervals for which valid Optical Monitor PM data is available
for the particular interface.
The value of this… | column | Unsigned32 | .1.3.6.1.4.1.3607.2.40.1.1.1.7 |
| cMsDwdmIfOTNValidIntervals This object gives the number of contiguous 15 minute
intervals for which valid OTN performance monitoring data is
available for the particular interface.
The valu… | column | Unsigned32 | .1.3.6.1.4.1.3607.2.40.1.1.1.8 |
| cMsDwdmIfFECValidIntervals This object gives the number of contiguous 15 minute
intervals for which valid FEC PM data is available
for the particular interface.
The value of this object wil… | column | Unsigned32 | .1.3.6.1.4.1.3607.2.40.1.1.1.9 |