cMsDwdmIfConfigLoopback
CERENT-MSDWDM-MIB ·
.1.3.6.1.4.1.3607.2.40.1.1.1.3
Object
column
r/w
Enumeration
This object allows the management client to configure
loopback for the client side or trunk side interfaces.
'noLoop' - No Loopback present.
'diagnosticLoop' - This is an internal loopback, where the
data stream is looped from the transmit
to receive section. It is used for
hardware debug, bring-up and diagnostics.
'lineLoop' - In this mode, the receive data stream is
looped back to the transmit side.
'otherLoop' - This indicates loopbacks not defined here.
The default value of this object will be 'noLoop'.
Context
- MIB
- CERENT-MSDWDM-MIB
- OID
.1.3.6.1.4.1.3607.2.40.1.1.1.3- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- cMsDwdmIfConfigEntry
- Table
- cMsDwdmIfConfigTable
- Siblings
- 9
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | noLoop |
2 | diagnosticLoop |
3 | lineLoop |
4 | otherLoop |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| cMsDwdmIfConfigProtocol This object is used to specify the protocol of the data
carried over the interface.
This object applies to linecards which support a variety of
protocols and allo… | column | ProtocolType | .1.3.6.1.4.1.3607.2.40.1.1.1.1 |
| cMsDwdmIfConfigFECMode This object allows the management client to enable
gathering FEC ( Forward Error Correction ) counters on
an applicable interface, by writing a value of 'enableStandard'
or 'e… | column | Enumeration | .1.3.6.1.4.1.3607.2.40.1.1.1.10 |
| cMsDwdmIfConfigDataRate This object allows the management client to set the
data rate across the interface.
passThru denotes 2R, Reamplification and reshaping.
stm1 denotes 3R, Reamp, … | column | Enumeration | .1.3.6.1.4.1.3607.2.40.1.1.1.2 |
| cMsDwdmIfConfigWavelength This object allows the management client to configure
the wavelength mode of operation to the applicable interfaces. | column | OpticalWavelength | .1.3.6.1.4.1.3607.2.40.1.1.1.4 |
| cMsDwdmIfConfigOtnStatus This object allows the management client to enable
the OTN (G.709) on an applicable interface,by writing a
value of 'true' to this object. To bypass the monitoring
hardware, … | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.3607.2.40.1.1.1.5 |
| cMsDwdmIfConfigFECStatus This object allows the management client to enable
gathering FEC ( Forward Error Correction ) counters on
an applicable interface, by writing a value of 'true'
to this object.… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.3607.2.40.1.1.1.6 |
| cMsDwdmIfOpticsValidIntervals This object gives the number of contiguous 15 minute
intervals for which valid Optical Monitor PM data is available
for the particular interface.
The value of this… | column | Unsigned32 | .1.3.6.1.4.1.3607.2.40.1.1.1.7 |
| cMsDwdmIfOTNValidIntervals This object gives the number of contiguous 15 minute
intervals for which valid OTN performance monitoring data is
available for the particular interface.
The valu… | column | Unsigned32 | .1.3.6.1.4.1.3607.2.40.1.1.1.8 |
| cMsDwdmIfFECValidIntervals This object gives the number of contiguous 15 minute
intervals for which valid FEC PM data is available
for the particular interface.
The value of this object wil… | column | Unsigned32 | .1.3.6.1.4.1.3607.2.40.1.1.1.9 |