cat2600TsNumberUFC

CAT2600-MIB · .1.3.6.1.4.1.9.1.111.1.2.1.1.27
MIB view Table view

Object

scalar mandatory Integer32 
The number of UFCs installed in the switch.  A value
of zero (or an SNMP error of NOSUCH) indicates there are
NO UFCs installed in this switch.
This value indicates the number of entries in the
cat2600TsUFCTable.

Context

MIB
CAT2600-MIB
OID
.1.3.6.1.4.1.9.1.111.1.2.1.1.27
Type
scalar
Access
readonly
Status
mandatory
Parent
cat2600TsConfig
Siblings
19

Syntax

Integer32
Source
COPS-PR-SPPIInteger32
Base type
Integer32

Values & Constraints

Type Constraints
range: -2147483648..2147483647

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
cat2600TsFwVer mandatory
The firmware version in the form major.minor. For port microcode (SOLO) version information see the mgmt.mib-2.interfaces.ifTable.ifEntry.ifDescr object.
scalarOctetString.1.3.6.1.4.1.9.1.111.1.2.1.1.1
cat2600TsDefaultGateway mandatory
IP default gateway used by the switch. Changes to this object take effect immediately.
scalarRFC1155-SMIIpAddress.1.3.6.1.4.1.9.1.111.1.2.1.1.10
cat2600TsTrapRcvrTable mandatory
A table of managers to which to send traps. Entries in the table are saved across resets and power cycles.
table-.1.3.6.1.4.1.9.1.111.1.2.1.1.14
cat2600TsPingInterval mandatory
This variable specifies the interval in seconds of sending ICMP Echo Requests to the default gateway. No PING packets will be sent if the value is set to 0. The default interval i…
scalarInteger32.1.3.6.1.4.1.9.1.111.1.2.1.1.19
cat2600TsHwVer mandatory
The hardware version in the form major.minor.
scalarOctetString.1.3.6.1.4.1.9.1.111.1.2.1.1.2
cat2600TsTapPort mandatory
Select the port to monitor traffic.
scalarInteger32.1.3.6.1.4.1.9.1.111.1.2.1.1.20
cat2600TsTapMonitoredPort mandatory
Allows the selection of the port that will be monitored by the port selected by cat2600TsTapPort.
scalarInteger32.1.3.6.1.4.1.9.1.111.1.2.1.1.21
cat2600TsCrcThresholdHi mandatory
Threshold for the switch to change to store and forward mode. A change in mode also generates a trap.
scalarInteger32.1.3.6.1.4.1.9.1.111.1.2.1.1.22
cat2600TsCrcThresholdLow mandatory
Threshold for the switch to change to store and forward mode. A change in mode also generates a trap.
scalarInteger32.1.3.6.1.4.1.9.1.111.1.2.1.1.23
cat2600TsPortSwitchModeChangeTrapEnable mandatory
Enable or disable the trap sent out when the switching mode changes from cut-through to store and forward.
scalarEnumeration.1.3.6.1.4.1.9.1.111.1.2.1.1.24
cat2600TsTrendThreshold mandatory
Based on trend calculation of the Dynamic Cut State algorithm, when this value is exceeded the port changes from cut-through to store and forward mode. The default value for this …
scalarInteger32.1.3.6.1.4.1.9.1.111.1.2.1.1.25
cat2600TsSamplingPeriod mandatory
Sampling period in minutes for determining if the error rate of CRC errors has been exceeded. The default value for this object is 10 minutes. The valid range is 1-120.
scalarInteger32.1.3.6.1.4.1.9.1.111.1.2.1.1.26
cat2600TsSerialNumber mandatory
System serial number.
scalarOctetString.1.3.6.1.4.1.9.1.111.1.2.1.1.3
cat2600TsInstallationDate mandatory
Firmware installation date. This date is initially set by the Network Management station. Each time the NV RAM is cleared through the console this date needs to be set by the mana…
scalarOctetString.1.3.6.1.4.1.9.1.111.1.2.1.1.4
cat2600TsFwSize mandatory
Size in bytes of the binary firmware image.
scalarInteger32.1.3.6.1.4.1.9.1.111.1.2.1.1.5
cat2600TsFwCRC mandatory
Firmware binary image CRC value.
scalarInteger32.1.3.6.1.4.1.9.1.111.1.2.1.1.6
cat2600TsFwManufacturer mandatory
Firmware manufacturer.
scalarOctetString.1.3.6.1.4.1.9.1.111.1.2.1.1.7
cat2600TsIpAddr mandatory
IP address of the switch. Changes to this object take effect immediately.
scalarRFC1155-SMIIpAddress.1.3.6.1.4.1.9.1.111.1.2.1.1.8
cat2600TsNetMask mandatory
IP subnet mask of the switch. Changes to this object take effect immediately.
scalarRFC1155-SMIIpAddress.1.3.6.1.4.1.9.1.111.1.2.1.1.9