cambiumpmp80211SoftwareUpdateError

Software Update error code:
0 - Finished successfully, waiting for reboot.
1 - SW update file download failed.
2 - Unpack failed, damaged or wrong format package.
3 - Firmware digital signature check failed.
4 - U-Boot digital signature check failed.
5 - Firmware FLASH write failed.
6 - U-Boot FLASH write failed.
7 - Boot partition switch failed.
8 - Board SKU is not supported for this firmware.
9 - Can't read firmware version, upgrade is impossible.
10 - Down-grade not supported for WiFi & ePTP modes.
11 - Down-grade below 2.3.1 is not supported for AP Lite device.
12 - Down-grade not supported for non SM TDD mode.
13 - Down-grade below 2.4.2 not supported for Force180/200 board types.
14 - Down-grade below 2.5.0 not supported for AP WiFi.
15 - Down-grade below 2.4.3 not supported for Reset Via Power Sequence.
16 - Down-grade below 2.4.3 not supported for Particular Country Locked device.
17 - Down-grade below 2.5.0 not supported for 2.5ms mode.
18 - Down-grade below 2.5.2 not supported for Use MAC Address as EAP-TTLS Username.
19 - Down-grade below 2.6.0 not supported for 5/10Mhz BW for WiFi & ePTP mode.
20 - Separate Management IP Port Forwarding and Data Port Mapping are not supported in SW versions below 2.6.0.
21 - General error. Device has no free memory.
22 - General error code.
23 - Downgrade below release 3.0 is not supported for ePMP2000.
24 - Incorrect firmware type for the current device type.
25 - Firmware file format is wrong for the current device type.
26 - Downgrade below 5.6.6 is not supported for ePMP-Elevate board type.
27 - Downgrade below 3.0.1 is not supported for 2.5G board type.
28 - Downgrade below 3.1 is not supported if Preffered AP Table contains SSIDs with spaces.
29 - Manifest Digital signature check failed.
30 - Downgrade below 3.4 is not supported for Force 190 boards.
31 - Downgrade below 3.5.2 is not supported for 6 GHz board type.
32 - Downgrade below 3.4 is not supported for Elevate 2.4 GHz board.
33 - Versions below 3.5 do not support License Server. Disable the License Server option before downgrade.
34 - Opening binary sw-upgrader failed.
35 - General error of upgrade process.
36 - Channel Bonding is not supported in SW versions below 4.1.1.
37 - 80 MHz channel bandwidth is not supported in SW versions below 4.1.1.
38 - NAT and Router modes are not supported in SW versions below 4.3.
39 - Downgrade below 3.5.4 is not supported for 802.11n devices and below 4.3 for 802.11ac devices with MAC addresses from pool 58:C1:7A:xx:xx:xx.
40 - MTU value other than 1538 is not supported in SW versions below 4.1.3.
41 - Downgrade below 4.3 is not supported for Force 300-16 boards.
42 - Membership VLAN/VLAN Mapping is not supported in SW versions below 4.3.
43 - Downgrade below 4.3 is not supported for ePMP3000 boards.
44 - 40 or 80 MHz channel bandwidth is not supported for ePMP3000 in SW versions below 4.3.1.
45 - Cannot upgrade this device with IPv6 enabled.
46 - Software Upgrade is Rejected because Trial Configuration is in progress.
47 - Downgrade below 4.4 is not supported for Force 300-13 or Force 300-19 boards.
48 - Downgrade below 4.5 is not supported for ePMP MP 3000 board.
49 - ePTP mode is not supported in SW versions below 4.5.
50 - 2.5 ms mode is not supported in SW versions below 4.6.
51 - 5/10Mhz BW mode is not supported in SW versions below 4.5.
52 - Reliable multicast is not supported in SW versions below 4.5.
53 - ACS is not supported in SW versions below 4.5.
54 - Standard WiFi Driver Mode is not supported in SW versions below 4.5.
55 - Omni/Split-Sector Antenna is not supported in SW versions below 4.5.
56 - Downgrade below 4.5.4 is not supported for 802.11n devices with MAC addresses from pool BC:E6:7C:xx:xx:xx.
57 - ACS/DCS is not supported in SW versions below 4.5.
58 - MTU value above 1700 is not supported in SW versions below 4.6.
59 - Downgrade below 4.6 is not supported for MIPS based boards.
60 - 70/30 65/35 60/40 55/45 45/55 40/60 35/65 downlink/uplink ratios are not supported in SW versions below 4.6.
61 - cnVision devices aren't supported in SW versions below 4.6.
62 - Downgrade below 4.6.1 is not supported for Force 300-25 V2 board.
63 - Downgrade below 4.7 is not supported for Force 200L.
64 - Cannot downgrade below 4.6.1 if DL Max Rate is not set to Use AP's config.
65 - DPI is not supported in SW versions below 4.7.
66 - WLR Driver Mode is not supported in SW versions below 5.2.0.
67 - Downgrade below 5.2 is not supported for 6GHz boards.
68 - Intelbras or Mikrotik licenses activated. Versions below 4.7 don't support those.
69 - Downgrade below 4.7 is not supported for boards with soft country lock set.
70 - Downgrade below 5.4 is not supported for this type of devices.
71 - Downgrade below 4.7 is not supported for boards with flexible mode selected.
72 - Downgrade below 4.7 is not supported for boards with Port Forwarding configured containing ports 22(SSH), 161(SNMP), 80(HTTP), 443(HTTPS)
73 - TR-069 option is not supported in SW versions below 5.2 on 802.11ax devices and 4.7 on other devices.
74 - Downgrade below 4.6.4 is not supported for this device hardware.
75 - Downgrade below 4.7.1 is not supported for Force 300-25L V2 board.
77 - Downgrade below 4.7.1 is not supported with IPv6 mode selected other than Static or DHCP
Device Allocation: AP, SM

MIB

CAMBIUM-PMP80211-MIB

OID

.1.3.6.1.4.1.17713.21.4.13

Type

scalar

Access

readonly

Status

current

Parent

cambiumpmp80211SystemActions