ethIntfLineMapping

BTI-7000-MIB · .1.3.6.1.4.1.18070.2.2.1.4.14.1.40
MIB view Table view

Object

column r/w Enumeration 
For 10 GE interfaces, both 10 GE LAN PHY and OTU2 encapsulated
10GE LAN PHY will be supported. The line mapping attribute
allow provisioning of either of the protocol. This attributes 
applies to 10 GE interfaces only. When a 10 GE interface is configured
as a stacking port, this field is set to stacking.
              
NOTE:  This parameter does not apply to gigabitEthernet type
interfaces, attempts to set this for gigE port types will fail.
              
Reading this object for non-10GigE interfaces will return 
notApplicable.

Context

MIB
BTI-7000-MIB
OID
.1.3.6.1.4.1.18070.2.2.1.4.14.1.40
Type
column
Access
readwrite
Status
current
Parent
ethIntfEntry
Table
ethIntfTable
Siblings
46

Syntax

Enumeration

Values & Constraints

No enumerated values or constraints recorded.

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
ethIntfShelfIdx
The number of the shelf in which the Ethernet facility resides.
columnInteger32.1.3.6.1.4.1.18070.2.2.1.4.14.1.1
ethIntfOpticalPwrTransmitted
The optical power transmitted at the output of the transceiver.
columndBm/10 BTI-TC-MIBFixedX10.1.3.6.1.4.1.18070.2.2.1.4.14.1.10
ethIntfRowStatus
Used to control the addition and deletion of entries in the Ethernet table, which in turn controls provisioning and deprovisioning of Ethernet facilities.
columnSNMPv2-TCRowStatus.1.3.6.1.4.1.18070.2.2.1.4.14.1.100
ethIntfPEC
An optionally provisioned transceiver Product Equipment Code used to validate the physically present transceiver on the Ethernet port.
columnOctetString.1.3.6.1.4.1.18070.2.2.1.4.14.1.11
ethIntfAdminStatus
The administrative status of the Ethernet facility.
columnEnumeration.1.3.6.1.4.1.18070.2.2.1.4.14.1.12
ethIntfOperStatus
The reported operational status of the Ethernet facility.
columnBTI-TC-MIBOperStatus.1.3.6.1.4.1.18070.2.2.1.4.14.1.13
ethIntfOperStatQlfr
This is a textual list of qualifiers about the reported operational status of the Ethernet facility.
columnBTI-TC-MIBOperStatQlfr.1.3.6.1.4.1.18070.2.2.1.4.14.1.14
ethIntfAutoEnableTimer
Specifies the auto-enable timer for the targeted Ethernet facility. This value only applies if the AdminStatus object is set to autoEnabled. Otherwise, the value returned is 000-0…
columnBTI-TC-MIBHoursAndMinutes.1.3.6.1.4.1.18070.2.2.1.4.14.1.15
ethIntfActAutoEnableTimer
Indicates the time remaining on the auto-enable timer if it is actively counting down. Otherwise, the value returned is 000-00.
columnBTI-TC-MIBHoursAndMinutes.1.3.6.1.4.1.18070.2.2.1.4.14.1.16
ethIntfWavelength
The wavelength to be transmitted by the transceiver on the Gigabit Ethernet facility port. This is a mandatory object when a row of the Ethernet table is created.
columnBTI-TC-MIBFixedX100.1.3.6.1.4.1.18070.2.2.1.4.14.1.17
ethIntfVendorPN1
An optionally provisioned part number used to validate the optical transceiver on the Ethernet facility port.
columnOctetString.1.3.6.1.4.1.18070.2.2.1.4.14.1.18
ethIntfVendorPN2
An optionally provisioned part number used to validate the optical transceiver on the Ethernet facility port.
columnOctetString.1.3.6.1.4.1.18070.2.2.1.4.14.1.19
ethIntfSlotIdx
The number of the slot in which the Ethernet facility resides.
columnInteger32.1.3.6.1.4.1.18070.2.2.1.4.14.1.2
ethIntfVendorPN3
An optionally provisioned part number used to validate the optical transceiver on the Ethernet facility port.
columnOctetString.1.3.6.1.4.1.18070.2.2.1.4.14.1.20
ethIntfPhyPMMon
Indicates if the Ethernet facility is configured to report threshold crossing conditions for physical layer performance monitoring parameters.
columnEnumeration.1.3.6.1.4.1.18070.2.2.1.4.14.1.21
ethIntfFPSD
Indicates if the Ethernet facility is configured for Fault Propagation Shut Down.
columnEnumeration.1.3.6.1.4.1.18070.2.2.1.4.14.1.22
ethIntfLaserStatus
An indication of the operational status of the transceiver laser on the Ethernet facility port.
columnEnumeration.1.3.6.1.4.1.18070.2.2.1.4.14.1.23
ethIntfId1
Textual data recorded by the user to describe the provisioned facility in a manner useful to the user.
columnOctetString.1.3.6.1.4.1.18070.2.2.1.4.14.1.24
ethIntfFiberType
An optional specification of the fiber type that interfaces to the Ethernet facility port.
columnBTI-TC-MIBFiberType.1.3.6.1.4.1.18070.2.2.1.4.14.1.25
ethIntfCustom1
A variable length text string for operating company use.
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.18070.2.2.1.4.14.1.26
ethIntfSpeed
The speed of the Ethernet facility link. This object is mandatory to create a new facility and determines the type of interface, based on speed.
columnMbps SNMPv2-SMIGauge32.1.3.6.1.4.1.18070.2.2.1.4.14.1.27
ethIntfDuplex
The duplex mode of the Ethernet facility interface.
columnEnumeration.1.3.6.1.4.1.18070.2.2.1.4.14.1.28
ethIntfMediaRate
The configured media rate of the Ethernet facility interface. For 10 GE interfaces, the media rate can only be autoNegotiated.
columnBTI-TC-MIBMediaRateType.1.3.6.1.4.1.18070.2.2.1.4.14.1.29
ethIntfPortTypeIdx
The type of the port on the circuit pack.
columnBTI-TC-MIBPvxL1PortType.1.3.6.1.4.1.18070.2.2.1.4.14.1.3
ethIntfMTU
The MTU size for the Ethernet facility interface.
columnInteger32.1.3.6.1.4.1.18070.2.2.1.4.14.1.30
ethIntfLinkStatus
This object provides the link status information regarding the particular interface.
columnEnumeration.1.3.6.1.4.1.18070.2.2.1.4.14.1.31
ethIntfLagId
This object provides the information regarding the LAG Id of the particular interface.
columnInteger32.1.3.6.1.4.1.18070.2.2.1.4.14.1.32
ethIntfLagPortPriority
This object provides the information for lag port priority of the particular interface.
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.18070.2.2.1.4.14.1.33
ethIntfBER
The Signal Degrade Bit Error Ratio (SDBER) is used to configure the error rate threshold above which a Signal Degrade is declared.
columnBTI-TC-MIBBERType.1.3.6.1.4.1.18070.2.2.1.4.14.1.37
ethIntfMACAddr
The MAC address of the interface.
columnSNMPv2-TCMacAddress.1.3.6.1.4.1.18070.2.2.1.4.14.1.39
ethIntfPortIdx
The number of the port on the circuit pack on which the ethernet facility is provisioned.
columnInteger32.1.3.6.1.4.1.18070.2.2.1.4.14.1.4
ethIntfErrorCorrection
For 10G in OTU2 line-mapping mode, this object specifies the error correction mode. For interfaces in tenlanphy line-mapping mode, this object must be none. Attempts to set it to…
columnEnumeration.1.3.6.1.4.1.18070.2.2.1.4.14.1.41
ethIntfLpbkOpCmd
Used to perform a loopback operation on a transceiver facility as follows: - oprLpbk: operates a loopback on the transceiver - rlsLpbk: causes a previously invoked loopback to be …
columnEnumeration.1.3.6.1.4.1.18070.2.2.1.4.14.1.42
ethIntfRemoteId
Identifies the remote node and port to which the PVX ethernet port is connected, in the format prescribed by the PSM network management system.
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.18070.2.2.1.4.14.1.43
ethIntfMirrorConfig
Mirror configuration for the physical ethernet port
columnBTI-TC-MIBMirrorConfigType.1.3.6.1.4.1.18070.2.2.1.4.14.1.44
ethIntfLldpAdminStatus
The administratively desired status of the local LLDP agent. If the associated ethIntfLldpAdminStatus object has a value of 'enabled(1)', then the LLDP agent will t…
columnEnumeration.1.3.6.1.4.1.18070.2.2.1.4.14.1.45
ethIntfLldpRemChassisIdSubtype
The type of encoding used to identify the chassis associated with the remote system.
columnBTI-TC-MIBLldpChassisIdSubtype.1.3.6.1.4.1.18070.2.2.1.4.14.1.46
ethIntfLldpRemChassisId
The string value used to identify the chassis component associated with the remote system.
columnBTI-TC-MIBLldpChassisId.1.3.6.1.4.1.18070.2.2.1.4.14.1.47
ethIntfLldpRemPortIdSubtype
The type of port identifier encoding used in the associated 'ethIntfLldpRemPortId' object.
columnBTI-TC-MIBLldpPortIdSubtype.1.3.6.1.4.1.18070.2.2.1.4.14.1.48
ethIntfLldpRemPortId
The string value used to identify the port component associated with the remote system.
columnBTI-TC-MIBLldpPortId.1.3.6.1.4.1.18070.2.2.1.4.14.1.49
ethIntfOpticalPwrReceivedMinTh
This is the optical power received minimum threshold.
columndBm/10 BTI-TC-MIBFixedX10.1.3.6.1.4.1.18070.2.2.1.4.14.1.5
ethIntfBouncingStateChangeCount
Count of the Ethernet facility operational state changes sinse last reboot
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.18070.2.2.1.4.14.1.50
ethIntfOpticalPwrReceivedMaxTh
This is the optical power received maximum threshold.
columndBm/10 BTI-TC-MIBFixedX10.1.3.6.1.4.1.18070.2.2.1.4.14.1.6
ethIntfOpticalPwrTransmittedMinTh
This is the optical power transmitted minimum threshold.
columndBm/10 BTI-TC-MIBFixedX10.1.3.6.1.4.1.18070.2.2.1.4.14.1.7
ethIntfOpticalPwrTransmittedMaxTh
This is the optical power transmitted maximum threshold.
columndBm/10 BTI-TC-MIBFixedX10.1.3.6.1.4.1.18070.2.2.1.4.14.1.8
ethIntfOpticalPwrReceived
The optical power received on the input of the transceiver.
columndBm/10 BTI-TC-MIBFixedX10.1.3.6.1.4.1.18070.2.2.1.4.14.1.9