brpsTCPIPMethodServer

BROTHER-MIB · .1.3.6.1.4.1.2435.2.4.3.1240.5.2.17
MIB view Table view

Object

scalar mandatory r/w RFC1155-SMIIpAddress 
If TCP/IP configuration is setted up by any protocol server, 
this entry indicates the IP address of the server.

Context

MIB
BROTHER-MIB
OID
.1.3.6.1.4.1.2435.2.4.3.1240.5.2.17
Type
scalar
Access
readwrite
Status
mandatory
Parent
brtcpip
Siblings
21

Syntax

RFC1155-SMIIpAddress
Source
RFC1155-SMIIpAddress
Base type
OctetString

Values & Constraints

Type Constraints
range: 4

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
brpsTCPIPSupported mandatory
0 indicates the TCP/IP protocol is not supported. 1 indicates TCP/IP support is implemented by the firmware
scalarInteger32.1.3.6.1.4.1.2435.2.4.3.1240.5.2.1
brpsTCPIPRARPNoSubnet mandatory
If enabled, do not set the subnet mask based on the RARP response.
scalarInteger32.1.3.6.1.4.1.2435.2.4.3.1240.5.2.10
brpsTCPIPRARPNoGateway mandatory
If enabled, do not set the gateway/router address based on the RARP response.
scalarInteger32.1.3.6.1.4.1.2435.2.4.3.1240.5.2.11
brpsTCPIPUpdate mandatory
Hardware MAC address to be updated. This value is write only. Will read back as zeros.
scalarOctetString.1.3.6.1.4.1.2435.2.4.3.1240.5.2.12
brpsTCPIPBanner mandatory
0 indicates the LPR banner print is not enabled. 1 indicates that the LPR banner print is enabled.
scalarInteger32.1.3.6.1.4.1.2435.2.4.3.1240.5.2.13
brpsTCPIPFastTimeoutEnable mandatory
0 indicates the fast timeout is not enabled. 1 indicates that the fast timeout is enabled.
scalarInteger32.1.3.6.1.4.1.2435.2.4.3.1240.5.2.14
brpsTCPIPLPRRetryEnable mandatory
0 indicates the LPR print retry is not enabled. 1 indicates that the LPR print retry is enabled.
scalarInteger32.1.3.6.1.4.1.2435.2.4.3.1240.5.2.15
brpsTCPIPUseMethod mandatory
Method type that used set up TCP/IP configuration.
scalarInteger32.1.3.6.1.4.1.2435.2.4.3.1240.5.2.16
brpsTCPIPAccessTable mandatory
This table represents the list of IP address of node that has parmittion for access.Up to 16 Netware addresses can be enabled.
table-.1.3.6.1.4.1.2435.2.4.3.1240.5.2.18
brpsAdvancedTCPIPAccessSupported mandatory
0 indicates the Advanced TCP/IP Access is not supported. 1 indicates Advanced TCP/IP Access support is implemented by the firmware
scalarInteger32.1.3.6.1.4.1.2435.2.4.3.1240.5.2.19
brpsTCPIPEnable mandatory
0 indicates the TCP/IP protocol is not enabled. 1 indicates that the TCP/IP protocol is enabled. Writing a non-zero value will enable the TCP/IP protocol if it is supported by the…
scalarInteger32.1.3.6.1.4.1.2435.2.4.3.1240.5.2.2
brpsAdvancedTCPIPAccessEnable mandatory
0 indicates the Advanced TCP/IP Access is not enabled. 1 indicates that the Advanced TCP/IP Access is enabled.
scalarInteger32.1.3.6.1.4.1.2435.2.4.3.1240.5.2.20
brpsAdvancedTCPIPAccessAdministratorIPAddress mandatory
Administrator IPAddress.
scalarRFC1155-SMIIpAddress.1.3.6.1.4.1.2435.2.4.3.1240.5.2.21
brpsAdvancedTCPIPAccessSetting mandatory
0 indicates the Advanced TCP/IP Access is reject. 1 indicates that the Advanced TCP/IP Access is Accept.
scalarInteger32.1.3.6.1.4.1.2435.2.4.3.1240.5.2.22
brpsTCPIPAddress mandatory
IP Address assigned to the print server.
scalarRFC1155-SMIIpAddress.1.3.6.1.4.1.2435.2.4.3.1240.5.2.3
brpsTCPIPSubnetMask mandatory
Subnet mask assigned to the print server.
scalarRFC1155-SMIIpAddress.1.3.6.1.4.1.2435.2.4.3.1240.5.2.4
brpsTCPIPGateway mandatory
Gateway/Router address assigned to the print server.
scalarRFC1155-SMIIpAddress.1.3.6.1.4.1.2435.2.4.3.1240.5.2.5
brpsTCPIPMethod mandatory
Method used to determine the IP Address. AUTO tries all protocols. STATIC uses the configured address. DHCP, BOOTP, and RARP use only that protocol.
scalarInteger32.1.3.6.1.4.1.2435.2.4.3.1240.5.2.6
brpsTCPIPTimeout mandatory
Timeout used for LPD connections.
scalarInteger32.1.3.6.1.4.1.2435.2.4.3.1240.5.2.7
brpsTCPIPBootTries mandatory
Number of attempts to use BOOTP, RARP, and DHCP.
scalarInteger32.1.3.6.1.4.1.2435.2.4.3.1240.5.2.8
brpsTCPIPMaxWindow mandatory
Maximum window size for TCP connections. Due to resource limitations setting the window to values greater than 10240 is not recommended.
scalarInteger32.1.3.6.1.4.1.2435.2.4.3.1240.5.2.9