cmOverrideUcdMaxBurst
BRCM-CM-MGMT-MIB ·
.1.3.6.1.4.1.4413.2.2.2.1.2.1.12
Object
scalar
r/w
mini-slots Integer32
This object may be used to override the max burst value specified in
the burst descriptor corresponding to the long data grant IUC from the
upstream channel descriptor (UCD).
If set to the default value of 0, the CM will conform to the DOCSIS
specification requirements and abide by the max burst values as
specified in the UCD.
If set to any other value, the CM will limit burst sizes to either the
value specified by this object or the UCD specified value, whichever
is larger.
Setting this object to a value of 255 effectively means that the burst
size will be unlimited. This setting will maximize upstream
throughput.
Note that the value of this object has no effect on burst limitations
as configured by service flow parameter sets.
Context
- MIB
- BRCM-CM-MGMT-MIB
- OID
.1.3.6.1.4.1.4413.2.2.2.1.2.1.12- Type
- scalar
- Access
- readwrite
- Status
- current
- Units
- mini-slots
- Parent
- cmMgmtBase
- Siblings
- 12
Syntax
mini-slots Integer32
Values & Constraints
Object Constraints
range: 0-255
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| cmNumLLCFiltersSupported Indicates the number of entries in the docsDevFilterLLCTable
which can be supported on this particular device under current
operating conditions. Note that this is a conservati… | scalar | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.4413.2.2.2.1.2.1.1 |
| cmServiceQueueTable This table describes attributes of each upstream service queue on
a CM. | table | - | .1.3.6.1.4.1.4413.2.2.2.1.2.1.10 |
| cmForwardingHwAssistEnable Specifies whether the hardware forwarding assist engine is enabled,
for devices which support such assistace.
For devices which do not have hardware forwarding assist… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4413.2.2.2.1.2.1.11 |
| cmExtendedUsTxPowerCapability Specifies the maximum extended upstream transmit power of which this
device is capable. A value of zero indicates that the device has no
extended upstream power capability. Th… | scalar | quarter dBmV Integer32 | .1.3.6.1.4.1.4413.2.2.2.1.2.1.13 |
| cmNumIpFiltersSupported Indicates the number of entries in the docsDevFilterIpTable
which can be supported on this particular device under current
operating conditions. Note that this is a conservativ… | scalar | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.4413.2.2.2.1.2.1.2 |
| cmMiniFirewallEnable Specifies whether the CM mini-firewall will be enabled, provided the
mini-firewall feature is supported. If the feature is not supported,
this object will always report false(2) … | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4413.2.2.2.1.2.1.3 |
| cmDsdExtendedRetryEnable Specifies the behavior of the CM with regards to retrying DSD requests
when no reply is received. If set to true(1), the CM will continue
to retry the request until a reply is re… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4413.2.2.2.1.2.1.4 |
| cmCpeInterface For designs which are not capable of supporting multiple CPE interfaces
simultaneously, this object specifies the interface which will be
used as a CPE interface. Typical settin… | scalar | IANAifType-MIBIANAifType | .1.3.6.1.4.1.4413.2.2.2.1.2.1.5 |
| cmResetFactoryDefaults Setting this object to true(1) will cause the device to reset all
non-volatile settings to their factory default state, and the device
to be rebooted. Note that only dynamic sett… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4413.2.2.2.1.2.1.6 |
| cmTodRefreshInterval This object controls the length of time between periodic updates
of system time by way of a Time of Day (ToD) refresh. If set to
0, time of day will not be refreshed. Note that … | scalar | hours SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.4413.2.2.2.1.2.1.7 |
| cmDownstreamChannelInfoTable A table describing the characteristics of each downstream channel. An
entry exists in this table for each entry in the ifTable with an
ifType value of docsCableDownstream (128). | table | - | .1.3.6.1.4.1.4413.2.2.2.1.2.1.8 |
| cmIpProvisioningMode The value of this object determines the mode used by the CM for IP
provisioning.
If set to the default value of mdd(0), the CM will comply with the
DOCSIS 3.0 speci… | scalar | Enumeration | .1.3.6.1.4.1.4413.2.2.2.1.2.1.9 |